• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.1
• /
• pp.70-76
• /
• 1993

Burnishing, as a micro plastic working, is a finishing process used in conjuction with or in replacement of reaming, honing, lapping, and/or grinding. The tool which is a smooth, round steel ball slightly larger than the bore is pushed through pre-machined hole, leaving a closely controlled finish. The major application of the processes is to improve the geometric and mechanical properties of surface such as (1) dimensional accuracy, (2) surface roughness, (3) bearing ratio, (4) surface hardness, (5) wear resistance, (6) fatigue and corrosion resistance, etc. Therefore, this study carried out some experiments to illustrate the theoretical formula and to investigate surface accuracy (e.g. variation of diameter, surface roughness, bearing ratio) in accordance with the applied burnishing load.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.119-124
• /
• 1996

End milling operation is very important in machining precision components. Deterioration of surface roughness and surface geometry will cause more process for surface finishing. According to the feed rate and the cutting edge geometry, the cusp which is geometrically uncut surface is determined. To reduce the cost for dinishing operation after end milling, the cusp must be remaianed in small size as possible. Due to the cylindrical type of the end mill, tool deflection is one of the main problems in surface generation. The cutting resistance and the rigidity of the end mill will determine the size of tool deflection. One more important factor which deteriorate surface quality comes from the error in manufacturing end mills. Run-out of end mill which is the difference of the radius of each cutting edges will produce the difference of the cusp size in every rotation of end mill. These three major factors to the surface quality will be analized and the result will be compared with experimental ressult.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.947-952
• /
• 1997

The magnetic polishing is the useful method to finish using magnetic power of a magnet. The time hasn't been that long since the magnetic polishing method was introduced to korea as one of precision polishing techniques. However, the reasons for not being spreaded widely are the magnetic polishing method don't have mediocrity for machine, the efficiency of magnet-abrasive is confined as a bad polishing, and there are not many researchers in this field. The mechanism of this R&D is dealing with the dynamic state of magnet-abrasive. This paper deals with mediocritizing magnetic polishing device into regular lathe and this experiment was conducted in order to get a best surface roughness with low cost. Beside the subsidiary experiment was performed using the mixed magnet-abrasive with general alumina, barium. This paper introduced the main reason for difficulty using this method in industrial field. It needs more continues research on it. This paper contains the result of experiment to acquire the best surface roughness, not using the high-cost polishing material in processing. The average diameters of magnet-abrasive are the particles of 150 $\mu\textrm{m}$, 250 $\mu\textrm{m}$.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.12 s.255
• /
• pp.1634-1641
• /
• 2006

High-precision centerless grinding machines are emerging as a means of finishing the outer diameter grinding process required for ferrules, which are widely used as fiber optic connectors. In this study, a sensitivity analysis for structural and thermal characteristics was carried out using a virtual prototype of a centerless grinding machine to realize systematic design technology and performance improvements required to manufacture ferrules. The prototype consisted of a concrete-filled bed, hydrostatic grinding wheel (GW) and regulating wheel (RW) spindle systems, a hydrostatic RW table feed mechanism, a RW swivel mechanism, and on-machine GW and RW dressers. The results of the structural sensitivity analysis illustrated that the vertical stiffness of hydrostatic guideway for the RW table feed system greatly influenced the horizontal loop stiffness, and the results of the thermal sensitivity analysis illustrated that the heat generation rates at hydrostatic bearings and belt pulley greatly influenced the temperature rise of hydrostatic bearings and the deviation of thermal displacement between GW and RW.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.354-357
• /
• 2005

When Ti-6Al-4V is used in long steam turbine blades, the main issues are how to improve the fatigue strength as a problem of internal quality and how to forge the thinnest possible blades as problem of dimensional precision. To assure an excellent fatigue strength, it is important to make the two phase fine and equiaxial structure by providing enough plastic deformation in the two phase$(\alpha\;phase/\beta\;phase)$ temperature region. Accordingly, it needs to predict that forging temperature, preform design and forging velocity in forging process. To achieve this end, the two steps forging process was suggested to forge the thin and twisted blades with a precision hammer considering die forces and metal flow. Two steps forging process consists of the flattening forging process and finishing forging process. Process in forging of a 1016mm long steam turbine blade is designed by the finite element method. This study attempts to derive systematic design procedures for process design in the forging. Forging parameters was analyzed in two-dimensional plane-strain simulation and two steps forging process carried out in three-dimensional simulation. Consequently, optimal forging process parameters of long steam turbine blades in Ti-6Al-4V with a high dimensional precision are selected in the hammer die forging.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.3 no.1
• /
• pp.7-14
• /
• 2004

Machining error is defined the normal distance between designed surface and actual tool path with tool deflection. This is inevitably caused by the tool deflection, tool wear, thermal effect and machine tool errors and so on. Among these factors, tool deflection is usually known as the most significant factor of machining error. Tool deflection problem is analyzed using Instantaneous horizontal cutting forces. The high quality and precision of machining products are required in finishing. In order to achieve these purposes, it is necessary work that decrease the machining error. This paper presents a study on the machining error caused by the tool deflection in ball end milling of 2 dimensional surface. Tool deflection model and simple machining error prediction model are described. This model is checked the validity with machining experiments of 2 dimensional surface. These results may be used to decrease machining error and tool path decision.

• Journal of the Korea Convergence Society
• /
• v.9 no.5
• /
• pp.145-150
• /
• 2018

In the machine tool spindle, various tasks ranging from roughing to finishing must be possible, and the functions of constant speed movement or rotation positioning must be performed. Therefore, there are many variables to be considered in the spindle design. The Swiss Turn Type spindle automatic lathe is a good machine tool for working pins with thinner shafts than a fixed automatic lathe. The Swiss Turn Type spindle is mainly used for precision machining of small products, so the machining precision should be high. The maximum outer diameter limit shall be Ø32 and the inner diameter limit shall be Ø6. In this study, the static and dynamic characteristics of the SCM440 material used in the spindle type automatic lathe were analyzed by applying it to the Swiss turn type spindle automatic lathe. Numerical analysis was used to obtain optimal design technique with high speed and high accuracy considering the factors affecting the static and dynamic characteristics of the spindle.

• Design & Manufacturing
• /
• v.2 no.6
• /
• pp.11-16
• /
• 2008

In order to satisfy the customer's variant needs for a product quality in recent years, a demand for developing higher precision machining technologies in a lot of application areas such as automobile, cellular phone and semiconductor has been increased more and more. Micro-magnetic induced polishing(${\mu}-MIP$) process is one of these precision technologies. In this study, to verify the parameters' effect of the ${\mu}-MIP$ process on the surface roughness improvement of the inclined workpiece, well planned experiment which was called the design of experiments was carried out. Considered parameters were spindle speed, inductor current, abrasive configuration and working gap between the workpiece and the solid tool. As a result, it was seen that the inductor current and the working gap greatly affected the surface roughness improvement. And to predict the surface roughness of the inclined workpiece, S/N ratio and first-order response surface model was developed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1265-1268
• /
• 2005

Due to the increase of the need for reliable high density information storage devices, the demand for precise machining of the slider in HDD is rapidly growing. The present fabrication process of slider bears some serious problems such as low yield ratio in mass production, which is mainly caused by inefficient machining processes in shaping camber and crown on the slider. In order to increase slider yield ratio in HDD, a new systematic machining process is proposed and developed in this work. This new machining process includes the use of magnetorheological (MR) fluid, a smart polishing material generally used for ultra-fine surface finishing of micro structures. It is shown that the process proposed in this work enables to make camber and crown pattern in the scale of few tens of nanometers. Experiment results shows that the MR polishing can be also used for shaping process of micro structures.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.6
• /
• pp.128-135
• /
• 2002

Burr is a projected part of finished workpiece. It is unavoidable and undesirable by-product of most metal cutting or shearing process. Also, it must be removed to improve the fit of machined parts, safety of workers, and the effectiveness of finishing operation. But deburring process Is one of manufacturing processes that have not been successfully automated, so deburring automation is strongly needed. This paper focused on developing a basic algorithm to find edge of workpiece and match two different image data for deburring automation which includes automatic recognition of parts, generation of deburring tool paths and edge/comer finding ability by analyzing the DXF drawing file which contains information of part geometry. As an algorithm fur corner finding, SUSAN method was chosen. It makes good performance in finding edge and corner in suitable time. And this paper suggested a simple algorithm to find matching point between CCD image and drawing file.