• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.3
• /
• pp.76-82
• /
• 2000

본 논문에서는 환경에 구속 받는 유연 매니퓨레이터의 힘/위치에 대하여 논하고자 한다. 일반적으로, 유연 매니퓨레이터의 모델링 방법은 분포 정수 모델과 집중 정수 모델로 분류할 수 있다. 전자인 분포 정수 모델을 이용해서는 평면 1 링크, 2 링크를 대상으로 한 위치/힘 제어는 가능하나, 운동 방정식의 복잡성으로 인하여 실시간에서 다 링크 다 관절 유연 매니퓨레이터의 힘/위치를 제어하기는 어렵게 여겨져 왔다. 본 논문에서는 집중 정수 모델링 방법인 집중 스프링 질량 모델(Lumped Spring Mass Model)을 이용하여 환경에 구속받는 유연 매니퓨레이터의 운동 방정식을 산출했다 이 모델을 실험기인 유연 매니퓨레이터 ADAM(Aerospace Dual Arm Manipulators)에 적용하여 실시간 위치/힘 제어 실험을 행하였으며, MATLAB를 이용하여 해석했다. 또한, ADAMS$^{TM}$ FEM를 이용하여 분포 정수 모델을 도출하여, 해석하였으며, 이 결과와 집중 정수 모델을 이용한 MATLAB 해석의 결과, 그리고 실험 결과를 비교 분석하여 본 논문에서 제안한 구속받는 유연 매니퓨레이터의 집중 정수 모델 타당성을 입증시켰다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.04b
• /
• pp.218-222
• /
• 1993

A sliding mode controller associated with the moving sliding surface is formulate for the tip position control of a single-link flexible manipulator. After establishing the plant model which characterizes a noncollocated control system, a discontinuous control law is then constructed by restricting that velocity state variables are not available from direct sensor measurements. Using the proposed control law favorable system responses are accomplished through shortening the reaching phase without increasing maximum control torque. Furthermore, a low sensitiveness to extraneous disturbance is obtained. Computer simulations are undertaken in order to demonstrate these superior control performance characteristics to be accrued from the proposed methodology.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.6
• /
• pp.20-27
• /
• 1994

This paper presents a controller design to coordinate a robot manipulator under unknown system parameters and bounded disturbance inputs. To control the motion of the manipulator, an inverse dynamics control scheme is applied. Since parameters of the robot manipulators such as mass and inertia are not perfectly known, the difference between the actual and estimated parameters works as a disturbance force. To identify the unknown parameters, an improved adaptive control algorithm is directly derived from a chosen Lyapunov's function candidate based on the Lyapunov's Second Method. A robust control algorithm is devised to counteract the bounded disturbance inputs such as contact forces and disturbing forces coming from the difference between the actual and the estimated system parameters. Numerical examples are shown using three degree-of-freedom planar arm.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.381-384
• /
• 2001

The combined stirring method to uniform distribution of particle is consisted of two strring force both electro-magnetic stirring generated from induction heating and mechanical stirring with graphite stirrer. PMMC billets were fabricated with the volume fractions ranged from 0% to 20% and particle sizes ranged from 14$\mu\textrm{m}$ to 25$\mu\textrm{m}$. It is important to control the size of primary ${\alpha}$-AI solid particles because it could become the cause of the particle pushing or capture phenomena from the fact that secondary dendrite arm spacing size depends on the cooling rate during the solidification in hypoeutectic AI-Si alloy.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.629-630
• /
• 2006

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.848-851
• /
• 2003

In this paper, a separating system for used CRT recycling is presented. Depend on manufacturer CRTs has small differences in dimension for the same model, but the dimensions of the panel are nearly same. To simplifying configuration of the system, we developed CRT fixing pallets for every model of CRT. The height of cutting position for every model of CRT will be same. The cutting machine has two rotating arm and use metal-bond type diamond cutting wheel. Instead of water, two vortex tube type air-coolers are used for the cooling of cutter. Workers in recycling factory are generally old people. Therefore, control program should be easy to use and operate. Thus we developed GUI with very simple interface.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.664-669
• /
• 2003

This paper proposes a swing-arm type dual-stage actuator, which consists of a PZT actuator for fine motion and a VCM(Voice Coil Motor) for coarse motion, for SFF ODD(Small Form Factor Optical Disk Drive), in order to achieve fast access speed and precise track following control. We focus our attention on the design and control of the PZT actuator, because there have been a lot of previous researches related to the VCM and dual-stage actuators. Due to the dual cantilever structure, the PZT actuator can generate precise translational tracking motion at its tip where optical pickup is attached at, and the effect of hysteric behavior of the PZT element is reduced. The dynamic model of the PZT actuator is derived by using the Hamilton's principle, and verified by comparing with the experimental frequency response. The sliding mode control is designed in order to be robust against modeling uncertainties. Simulations and experimental results confirm the effectiveness of the suggested control scheme.

• Journal of the Korean Society for Precision Engineering
• /
• v.6 no.2
• /
• pp.65-76
• /
• 1989

The objective of this paper is to design the variable structure system(VSS) controller for the tracking control of excavator which is driven by electro-hydraulic servomechansim. It is generally agreed that the dynamic characteristics of the robot arm such as excavator are coupled, time varying, and highly nonlinear, and also hydraulic system contains nonlinear characteristics in itself, so performing exact position control and trajectory tracking control need remarkable consideration. To solve this porblem, this system was designed as a variable structure system. The salient feature of VSS is that the sliding mode occur on a switching surface. While in sliding mode, the system remains insensitive to parameter variations and disturbances. This control algorithm was applied to a hydraulic excavator by simulaltion and to a simulator by experiment. And its effectiveness was verified. And the results of VSS for the electro-hydraulic excavator was compared with that of the PID when load disturbances and system parameter variations exist.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.832-936
• /
• 1996

In this paper, we study a dynamic characteristics of HDD. HDD is constructed by spindle motor/disk unit, cover, base, E-block arm/suspension unit, and rotary actuator/voice coil motor. First, we make a FE model of spindle motor/disk unit and analyzed natural frequency/mode analytically and experimentally. Especially, the change of natural frequecy of spindle motor unit according to change of B.C is considered. Second, FE model of cover, base is made. Third, we assemble the above three FE mode, we get HEE assembly and dynamic analysis of HDD assembly is accomplished.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1717-1722
• /
• 2003

In this paper we developed flip-chip bonder using XY stage, liner-rotary actuator and vision system. We depicted the major parts of the developed flip-chip bonder. Then we discussed several problems and their solutions such as vision and motion control, pick-up module position accuracy, separation of chip from the blue taped hoop, etc. We used a post guide to improve the horizontal positional accuracy against the long arm. Also, we used an ejector module and synchronization technique for easy chip separation from the blue tape.