• Restorative Dentistry and Endodontics
• /
• v.48 no.1
• /
• pp.8.1-8.8
• /
• 2023

Objectives: This study was designed to evaluate the parameters of bonding performance to root dentin, including push-out bond strength and dentinal tubular biomineralization, of a hydraulic bioceramic root-end filling material premixed with dimethyl sulfoxide (Endocem MTA Premixed) in comparison to a conventional powder-liquid-type cement (ProRoot MTA). Materials and Methods: The root canal of a single-rooted premolar was filled with either ProRoot MTA or Endocem MTA Premixed (n = 15). A slice of dentin was obtained from each root. Using the sliced specimen, the push-out bond strength was measured, and the failure pattern was observed under a stereomicroscope. The apical segment was divided into halves; the split surface was observed under a scanning electron microscope, and intratubular biomineralization was examined by observing the precipitates formed in the dentinal tubule. Then, the chemical characteristics of the precipitates were evaluated with energy-dispersive X-ray spectroscopic (EDS) analysis. The data were analyzed using the Student's t-test followed by the Mann-Whitney U test (p < 0.05). Results: No significant difference was found between the 2 tested groups in push-out bond strength, and cohesive failure was the predominant failure type. In both groups, flake-shaped precipitates were observed along dentinal tubules. The EDS analysis indicated that the mass percentage of calcium and phosphorus in the precipitate was similar to that found in hydroxyapatite. Conclusions: Regarding bonding to root dentin, Endocem MTA Premixed may have potential for use as an acceptable root-end filling material.

• Transactions of Materials Processing
• /
• v.31 no.3
• /
• pp.160-166
• /
• 2022

The purpose of this study is to investigate the effects of combined addition of Ca and Y on the precipitation and age-hardening behavior of an extruded AZ91 alloy by conducting the aging treatment at 200 ℃ for hot-extruded AZ91 and AZ91-0.3Ca-0.2Y alloys. In the AZ91 alloy, many Mg₁₇Al₁₂ discontinuous precipitate (DP) bands formed during air cooling immediately after extrusion are present, whereas in the AZ91-0.3Ca-0.2Y alloy, a few DP bands and numerous Al₂Y, Al₈Mn₄Y, and Al₂Ca phase particles are distributed along the extrusion direction. The peak-aging time of the AZ91-0.3Ca-0.2Y alloy is 16 hours, twice that of the AZ91 alloy. Although both alloys have similar hardness before aging treatment, the hardness after peak-aging treatment (i.e., peak hardness) of the AZ91-0.3Ca-0.2Y alloy is higher than that of the AZ91 alloy, as 93.1 and 88.7 Hv, respectively. The microstructures of both peak-aged alloys comprise DPs and continuous precipitates (CPs). However, the peak-aged AZ91-0.3Ca-0.2Y alloy has a smaller amount of DPs and a larger amount of CPs than the peak-aged AZ91 alloy. Additionally, the inter-particle spacings of DPs and CPs in the former are significantly narrower than those in the latter. These results demonstrate that the addition of small amounts of Ca and Y to a commercial AZ91 alloy considerably affects the formation rate, size, and amount of CPs and DPs during aging and resultant age-hardening behavior.

• Journal of Radiation Protection and Research
• /
• v.48 no.2
• /
• pp.77-83
• /
• 2023

Background: The purpose of this study is to purify uranium (U[VI])-contaminated soil-flushing effluent using the precipitation-distillation process for clearance. Precipitation and distillation are commonly used techniques for water treatment. We propose using a combination of these methods for the simple and effective removal of U(VI) ions from soil-flushing effluents. In addition, the U concentration (Bq/g) of solid waste generated in the proposed treatment process was analyzed to confirm whether it satisfies the clearance level. Materials and Methods: Uranium-contaminated soil was decontaminated by soil-flushing using 0.5 M sulfuric acid. The soil-flushing effluent was treated with sodium hydroxide powder to precipitate U(VI) ions, and the remaining U(VI) ions were removed by phosphate addition. The effluent from which U(VI) ions were removed was distilled for reuse as a soil-flushing eluent. Results and Discussion: The purification method using the precipitation-distillation process proposed in this study effectively removes U(VI) ions from U-contaminated soil-flushing effluent. In addition, most of the solid waste generated in the purification process satisfied the clearance level. Conclusion: The proposed purification process is considered to have potential as a soil-flushing effluent treatment method to reduce the amount of radioactive waste generated.

• Advances in nano research
• /
• v.13 no.4
• /
• pp.313-323
• /
• 2022

The microstructure and mechanical properties of Cr-Ni steel and Cr-Ni steel-matrix nanocomposites reinforced with nano-ZrO₂ particles were investigated in this study. Cr-Ni steel and Cr-Ni/ZrO₂ nanocomposites were produced using a combination of high-energy ball milling, pressing, and sintering processes. The microstructures of the specimens were analyzed using EDX and XRD. Compression and hardness tests were performed to determine the mechanical properties of the specimens. Nano-ZrO₂ particles were effective in preventing chrome carbide precipitate at the grain boundaries. While t-ZrO₂ was detected in Cr-Ni/ZrO₂ nanocomposites, m-ZrO₂ could not be found. Few α'-martensite and deformation bands were formed in the microstructures of Cr-Ni/ZrO₂ nanocomposites. Although nano-ZrO₂ particles had a negligible impact on the strength improvement provided by deformation-induced plasticity mechanisms in Cr-Ni/ZrO₂ nanocomposites, the mechanical properties of Cr-Ni steel were significantly improved by using nano-ZrO₂ particles. The hardness and compressive strength of Cr-Ni/ZrO₂ nanocomposite were higher than those of Cr-Ni steel and enhanced as the weight fraction of nano-ZrO₂ particles increased. Cr-Ni/ZrO₂ nanocomposite with 5wt.% nano-ZrO₂ particles had almost twofold the hardness and compressive strength of Cr-Ni steel. The nano-ZrO₂ particles were considerably more effective on particle-strengthening mechanisms than deformation-induced strengthening mechanisms in Cr-Ni/ZrO₂ nanocomposites.

• Pediatric Infection and Vaccine
• /
• v.31 no.1
• /
• pp.140-146
• /
• 2024

Multisystem inflammatory syndrome in children (MIS-C) is a rare complication of coronavirus disease 2019 (COVID-19), causing multi-organ damage affecting the heart, lungs, kidneys, digestive tract, and nervous system. As the cases of MIS-C have been increasing following the COVID-19 pandemic, the importance of appropriate management for MIS-C is becoming increasingly apparent. Immunomodulating agents such as anakinra, infliximab, and steroids are regarded as supplementary therapy to the first-line treatment with intravenous immunoglobulin. However, these immunomodulating therapies can potentially precipitate opportunistic infections, including those caused by cytomegalovirus (CMV), Epstein-Barr virus, and tuberculosis, or increase the risk of co-infections. Herein, we report a case of a 3-year-old boy who was treated with immunoglobulin, infliximab, and high-dose methylprednisolone for MIS-C, and subsequently developed a persistent fever lasting 32 days caused by a CMV infection.

• Design & Manufacturing
• /
• v.17 no.4
• /
• pp.63-71
• /
• 2023

In order to increase the extrusion production speed of aluminum, extrusion die cooling technology using liquid nitrogen has recently attracted a lot of attention. Increasing the extrusion speed increases the temperature of the bearing area of extrusion dies and the extrusion profile, which may cause defects on the surface of extruded profile. Extrusion die cooling technology is to directly inject liquid nitrogen through a cooling channel formed between the die and the backer inside the die-set. The liquid nitrogen removes heat from the die-set, and gaseous nitrogen at the exit of the channel, covers the extrusion profile of an inert atmosphere reducing the oxidation and the profile temperature. The aim of this study is to evaluate the cooling capacity by applying die cooling to extrusion of Al-Mn-based aluminum alloy flat tubes, and to investigate the effects of die cooling on the change in extrusion characteristics of flat tubes. Cooling capacity was confirmed by observing the temperature change of the extrusion profile depending on whether or not die cooling is applied. To observe changes in material characteristics due to die cooling, surface observation is conducted and microstructure and precipitate analysis are performed by FE-SEM on the surface and longitudinal cross section of the extruded flat tubes.

• Transactions of Materials Processing
• /
• v.33 no.3
• /
• pp.161-168
• /
• 2024

Aluminum alloy sheets, compared to conventional steel sheets, face challenges in press forming due to their lower elongation. To enhance their formability, extensive research has focused on forming technologies at elevated temperatures, specifically warm forming at around 300℃ and hot forming at approximately 500℃. This study proposes that the formability of aluminum alloy sheets can be significantly enhanced using a multi-stage hot forming technique. The research also investigates whether the strength of the A6061 aluminum alloy, known for its precipitation hardening, can be maintained when formed below the precipitate solid solution temperature. In the experiments, the A6061-T6 sheet underwent heating and rapid cooling between 250 and 500℃. The mechanical properties were evaluated at each stage of the process. The findings revealed that when the initial heat treatment was below 350℃, the strength of the material remained unchanged. However, at temperatures above 400℃, there was a noticeable decrease in strength coupled with an increase in elongation. Conversely, when the secondary heat treatment was conducted at temperatures of 350℃ or lower, the strength remained comparable to that of the initial heat treated material. However, at higher temperatures, a reduction in strength and an increase in elongation were observed.

• Hip & pelvis
• /
• v.36 no.1
• /
• pp.1-11
• /
• 2024

Gout is triggered by the accumulation of uric acid in the body, leading to hyperuricemia. Genetic, metabolic, and environmental factors can influence this condition. Excessive uric acid buildup results in the formation of monosodium urate (MSU) crystals, which precipitate in specific areas of the body, including the joints, where they can cause symptoms of gout. While the acute and chronic symptoms of gout have been well-documented, diagnosis of gout affecting the hip joint poses significant challenges. The global incidence of gout, the most prevalent form of inflammatory arthritis, is on the rise. Evaluation of the clinical signs, laboratory results, and imaging results is generally required for diagnosis of gout in cases where MSU crystals have not been detected. Hyperuricemia is considered a primary cause of arthritis symptoms, and comprehensive guidelines for treatment are available. Therefore, the choice of medication is straightforward, and moderate effectiveness of treatment has been demonstrated. Gout is a chronic disease, requiring lifelong uric acid-lowering medications, thus application of a treatment strategy based on the target blood uric acid concentration is necessary. Consequently, cases of gout will likely be observed more frequently by hip surgeons in clinical scenarios in the future. The objective of this review is to provide an overview of the pathophysiology of gout and subsequently examine recent advances in diagnostic methods and therapeutic agents based on an understanding of its underlying mechanisms. In addition, literature on gout-related issues affecting the hip joint, providing a useful reference for hip surgeons is examined.

• Korean Journal of Soil Science and Fertilizer
• /
• v.8 no.2
• /
• pp.89-96
• /
• 1975

The experiment was carried out to investigate the chemical properties of cement kiln dusts, abundantly produced from cement industry as a byproduct, and their effectiveness on rice yield. The field experiment was conducted on the acid paddy soil developed on basalt at Dongsong-Myon, Chulwon-Kun, Gangwon-Do. Two kinds of cement kiln dusts were used ; By Pass (BP) collected from the suspension preheater and Electric Precipitate (EP) from the cottrell electric precipitator. The levels of cement kiln dust applied were 100kg/10a, 200kg/10a and 300kg/10a, and the recommended variety "Nong Back" was adopted for this experiment. The results obtained are summarized as follows ; 1. The component of cement kiln dusts seems to be quite suitable for liming material. BP has 55% alkalinity, 41.7% of soluble calcium, 9.8% of soluble magnesium and 4.5% of water soluble silicate, while EP has 53.5% alkalinity, 41.7% soluble calcium, 8.3% soluble magnesium and 1% water soluble silicate. 2. The relative effectiveness of cement kiln dust in the soil will be superior due to very fine particle size. EP pass through completely 270 mesh screen, and 95% of BP pass through 150 mesh screen, 68% passing 270 mesh. 3. BP application at the rate of 100kg/10a increased 21% of rice yield as compared with control and EP 15%. It was observed that the affected yield components were increased panicle number per hill, grain number per panicle and 1,000 grains weight. 4. The application of optimum amount (100kg/10a) of cement kiln dusts accelerated the uptake of nutrients by rice plant and increased rice yield. However, the excess amounts (200kg/10a, 300kg/10a) of cement kiln dusts retarded the uptake of nutrients from soil.

• Radiation Oncology Journal
• /
• v.19 no.2
• /
• pp.163-170
• /
• 2001

Purpose : The measurement of radiation survival using a clonogenic assay, the established standard, can be difficult and time consuming. In this study, We have used the MTT assay, based on the reduction of a tetrazolium salt to a purple formazan precipitate by living cells, as a substitution for clonogenic assay and have examined the optimal condition for performing this assay in determination of radiation sensitivity. Materials and Methods : Four human cancer cell lines - PCI-1, SNU-1066, NCI-H630 and RKO cells have been used. For each cell line, a clonogenic assay and a MTT assay using Premix WST-1 solution, which is one of the tetrazolium salts and does not require washing or solubilization of the precipitate were carried out after irradiation of 0, 2, 4, 6, 8, 10 Gy. For clonogenic assay, cells in $25\;cm^2$ flasks were irradiated after overnight incubation and the resultant colonies containing more than 50 cells were scored after culturing the cells for $10\~14$ days. For MTT assay, the relationship between absorbance and cell number, optimal seeding cell number, and optimal timing of assay was determined. Then, MTT assay was performed when the irradiated cells had regained exponential growth or when the non-irradiated cells had undergone four or more doubling times. Results : There was minimal variation in the values gained from these two methods with the standard deviation generally less than $5\%$, and there were no statistically significant differences between two methods according to t-test in low radiation dose (below 6 Gy). The regression analyses showed high linear correlation with the $R^2$ value of $0.975\~0.992$ between data from the two different methods. The optimal cell numbers for MTT assay were found to be dependent on plating efficiency of used cell line. Less than 300 cells/well were appropriate for cells with high plating efficiency (more than $30\%$). For cells with low plating efficiency (less than $30\%$), 500 cells/well or more were appropriate for assay. The optimal time for MTT assay was after 6 doubling times for the results compatible with those of clonogenic assay, at least after 4 doubling times was required for valid results. In consideration of practical limits of assay (12 days, in this study) cells with doubling time more than 3 days were inappropriate for application. Conclusion : In conclusion, it is found that MTT assay can successfully replace clonogenic assay of tested cancer cell lines after irradiation only if MTT assay was undertaken with optimal assay conditions that included plating efficiency of each cell line and doubling time at least.