• 한국환경과학회지
• /
• 제25권2호
• /
• pp.231-238
• /
• 2016

In this study, we have investigated to find optimal pre-treatment flocculation condition by analyzing the floc growth rate with mixing conditions and the membrane permeation flux for pre-treatment step of the membrane process. The higher mixing intensity showed a constant floc size index (FSI) values, and lower mixing intensity increased the degree of dispersion of the FSI values. Results of comparing the distribution characteristics of the FSI value and the permeation flux were more effective in increasing flux when the FSI values were 0.2 or higher. The degree of dispersion of FSI was relatively large in 40 rpm mixing condition compared to 120 rpm. In 40 rpm mixing condition, it decreased the permeation flux compared to 120 rpm because various sizes of flocs were distributed. Coagulation-UF membrane process enhanced 30%~40% of the flux rate compare to UF alone process, and the coagulation-MF process increased up to 5% of the flux rate compare to MF alone process. Pre-treatment, that is, coagulation process, has been found to be less effects on relatively larger pore size for MF membrane. For UF membrane, the flux was a little bit same when applying only the rapid mixing process or rapid mixing with slow mixing processes together. In case of MF membrane, the flux was improved when rapid mixing process applied with slow mixing process together.

• 한국초전도ㆍ저온공학회논문지
• /
• 제8권3호
• /
• pp.1-4
• /
• 2006

The characteristics of Bi2212 round wire was systematically studied depending on different heat treatment conditions. Initial wire was drawn after routine PIT (Powder In Tube) process. The wire was divided into 3 pieces with 10 cm in length and 2.5 mm in diameter. 3 wires were pre-heat treated separately by different heat treatment schedules, heated in air and nitrogen atmosphere and centrifugally melted. Pre-heated wires were annealed at $845^{\circ}C$ for 40 hours in oxygen atmosphere. SEM results indicate that all pre-heated wires showed highly oriented microstructure. However the wire by centrifugally melted process showed higher density and better electric properties as compared with 2 other wires pre-heated in air and nitrogen atmosphere. The critical current of a centrifugally melted wire was about 18 A in 77 K.

• 한국염색가공학회:학술대회논문집
• /
• 한국염색가공학회 2009년도 학술발표대회
• /
• pp.213-214
• /
• 2009

In order to promote an efficiency CPB process, we developed microwave system in CPB process. The whiteness and penetration ability of microwave-CPB pre-treated fabrics were superior to CPB only. This results indicates that microwave-CPB pre-treatment promotes CPB efficiency in agent usages and batching time.

• 한국염색가공학회지
• /
• 제29권3호
• /
• pp.122-130
• /
• 2017

In the direct digital textile printing process, the pre-treatment process is an essential condition for products by forming a clear pattern by sticking and penetration of DTP dye without spreading on the fabric. Recently, pre-treatment agent is changing from high viscosity to low viscosity in order to reduce defects of fabric during pre-treatment process. In this study, pre-treatment agent of acrylic polymer with low viscosity(less than 50cps) was prepared according to the solid content of the polymer, pre-treated on the cotton fabric, and direct DTP printing was performed to compare the color and sharpness. As a result, it showed high color at a viscosity of 50cps or less. When the solid content of the polyacrylic acid having a high molecular weight(A1) was 2.5wt%, when the solid content of the polyacrylic acid having a low molecular weight(A2) was 1 - 1.5wt%, the color was the best. And when the solid content of A1 and A2 was 1.5wt%, the degree of spreading was small and A1 was superior to A2 at the sharpness.

• 한국전기전자재료학회논문지
• /
• 제16권3호
• /
• pp.190-194
• /
• 2003

Dielectric thin films of (P $b_{0.72}$,L $a_{0.28}$) $Ti_{0.93}$ $O_3$ (PLT(28)) have been deposited on Pt(111)/Ti/ $SiO_2$/Si(100) substrates in-situ by pulsed laser deposition using different annealing and deposition Processes. We have investigated the effect of hydrogen annealing on the ferroelectric properties of PLT thin films and found that the annealing process causes the diffusion of hydrogen into the ferroelectric film resulting in the destruction of polarization. We have tried to form the film by a two-step deposition process In order to improve electrical property. Two-step process to grow PLT films was adopted and verified to be useful to enlarge the grain size of the film and to reduce the leakage current characteristics. Structural properties and electrical properties including dielectric constant, ferroelectric characteristics, and leakage current of PLT thin films were shown to be strongly influenced by grain size. The film deposited by using two-step Process including pre-annealing treatment has a strongly(111) orientation. However, the films deposited by using single -step process with hydrogen annealing process show the smallest grain size. The film deposited by using two-step process including pre-annealing treatment shows the leakage current density of below 10$^{-7}$ A/c $m^2$ for the field of smaller than 100 kV/cm. However, the films deposited by using single-step process with hydrogen annealing process and pre-annealing process show worse leakage current density than the film deposited by using two-step process including pre-annealing treatment.tment.

• Environmental Engineering Research
• /
• 제19권1호
• /
• pp.59-66
• /
• 2014

The aim of this study was to assess the effect of pre-aeration on sludge solubilization and the behaviors of nitrogen, dissolved sulfide, sulfate, and siloxane. The results of this study showed that soluble chemical oxygen demand in sewage sludge could be increased through pre-aeration. The pre-aeration process resulted in a higher methane yield compared to the anaerobic condition (blank). The pre-aeration of sewage sludge, therefore, was shown to be an effective method for enhancing the digestibility of the sewage sludge. In addition, this result confirms that the pre-aeration of sewage sludge prior to its anaerobic digestion accelerates the growth of methanogenic bacteria. Removal rates for $NH_3$-N and T-N increased simultaneously during pre-aeration, indicating simultaneous nitrification and denitrification. The siloxane concentration in sewage sludge decreased by 40% after 96 hr of pre-aeration; in contrast, the sulfide concentration in sewage sludge did not change. Therefore, pre-aeration can be employed as an efficient treatment option to achieve higher methane yield and lower siloxane concentration in sewage sludge. In addition, reduction of nitrogen loading by pre-aeration can reduce operating costs to achieve better effluent water quality in wastewater treatment plant and benefit the anaerobic process by minimizing the toxic effect of ammonia.

• 한국표면공학회지
• /
• 제54권4호
• /
• pp.184-193
• /
• 2021

This study demonstrates formation behavior and morphological changes of PEO (Plasma Electrolytic Oxidation) films on AZ91 Mg alloy as a function of pre-treatment time in 1 M HF solution at 25 ± 1 ℃. The electrochemical behavior and morphological changes of AZ91 Mg alloy in the pre-treatment solution were also investigated with pre-treatment time. The PEO films were formed on the pre-treated AZ91 Mg alloy specimen by the application of anodic current 100 mA/cm² of 300 Hz AC in 0.1 M NaOH + 0.4 M Na₂SiO₃ solution. Vigorous generation of hydrogen bubbles were observed upon immersion in the pre-treatment solution and its generation rate decreased with immersion time. It was also found that 𝛽-Mg₁₇Al₁₂ in AZ91 Mg alloy was dissolved and a protective thin film of MgF₂ was formed on the AZ91 Mg alloy surface during the pre-treatment process in the 1 M HF solution. PEO film did not grow on the AZ91 Mg alloy specimen when the surface was not pre-treated and irregular PEO films with nodular defects were formed for the specimens pre-treated up to 1 min. Uniform PEO films were formed when the AZ91 Mg alloy specimen was pre-treated more than 3 min. The growth rate of PEO films on AZ91 Mg alloy increased significantly with increasing pre-treatment time.

• 한국축산시설환경학회지
• /
• 제10권2호
• /
• pp.81-86
• /
• 2004

본 연구는 유지관리비가 적게 소요되고 관리가 용이한 에너지절감형 축산뇨오수 처리기술을 개발하기 위하여 목편 살수여상과 활성오니를 정화기술하는 처리기술을 연구하였다. 1. 스크레파 축사의 축산뇨오수 처리를 위한 목편칩 살수여상 활성오니 연계 시스템을 개발하였다. 처리공정은 축산뇨오수 원수$\to$스크린$\to$목편칩 살수여상$\to$활성오니$\to$침전/오존처리 공정으로 처리하였다. 2. 처리결과 축산뇨오수 원수의 BOD 8,620mg/$\iota$ 에서 최종처리수의 BOD는 58mg/$\iota$로 처리되었다. 또한 COD_{Mn},은 원수 4,290mg/$\iota$에서 232mg/$\iota$, SS 2,228mg/$\iota$에서 49.5mg/$\iota$, T-N 4,223mg/$\iota$에서 395mg/$\iota$, T-P 97.4mg/$\iota$에서 8.0mg/$\iota$로 처리되었다. 3. SS는 목편살수여상조에서 $71.1\%$가 제거되어 활성오니 처리 대비 슬러지 발생량이 $70\%$ 절감되었다.

• 한국환경과학회지
• /
• 제12권4호
• /
• pp.469-476
• /
• 2003

In order to examine the pre-treatment effect of crab shell en Pb$^{2+}$ removal by crab shell in aqueous solution, acid and alkali pre-treated crab shell were used. Electron microscopy techniques such as TEM (transmission electron microscopy) and SEM (scanning electron microscopy), and EDX (energy dispersive X-ray) and FTIR (Fourier transform infrared) spectrometry techniques were used to investigate the process of Pb$^{2+}$ removal by acid and alkali pre-treated crab shell. The Pb$^{2+}$ removal by acid pre-treated crab shell was much lower than that by untreated crab shell because of the decrease of CaCO$_3$ from the crab shell. However, the Pb$^{2+}$removal by alkali pre-treated crab shell increased compared to that by untreated crab shell. The results were confirmed by TEM, SEM, EDX and FTIR.nd FTIR.

• 한국의류학회지
• /
• 제27권5호
• /
• pp.582-587
• /
• 2003

To examine the effect of heat treatment temperature in finishing process on PET/PBT Fabric, PET/PBT Fabrics were treated at different relaxing temp., pre-set temp., and final-set temp.. The dimensions such as thickness and density were measured, and the handles were evaluated by Kawabata system. In relaxing which was wet heat treatment, thickness and bulkiness were increased, and NUMERI, FUKURAMI, SOFUTOSA, and THV also were increased but KOSHI was decreased with elevating temperature. With elevating pre-set temp., thickness and bulkiness were decreased, but KOSHI was increased. NUMERI, FUKURAMI, SOFUTOSA, and THV were the best at 180$^{\circ}C$ pre-set treatment. In final-set which was dry heat treatment like pre-set, thickness, bulkiness, NUMERI, HUKURAMI, SOFUTOSA, and THV were decreased, but KOSHI value was increased with elevating temperature. Therefore the best heat treatment condition was 130$^{\circ}C$ relaxing, 180$^{\circ}C$ pre-set, and 160$^{\circ}C$ final-set. And the handle of PET/PBT Fabric was affected much more by relaxing temp. than pre-set temp. and final-set temp.