• 한국자동차공학회논문집
• /
• 제16권5호
• /
• pp.106-112
• /
• 2008

Modern vehicles require a high degree of refinement, including good drive ability to meet customer demands. Vehicle drive ability, which becomes a key decisive factor for marketability, is affected by many parameters such as engine control and the dynamic characteristics in drive lines. This paper focuses on the simulation of FTP-75 mode which is considered with spark timing control on transient condition. The acceleration is the most important factor for vehicle fuel economy. The retard of spark timing increases in proportion to acceleration. Likewise, bsfc(break specific fuel consumption) which is affected by spark timing also increases in proportion to acceleration. The result of simulation considered transient condition shows 0.3% of error comparing with a test on chassis-dynamometer.

• 한국음향학회:학술대회논문집
• /
• 한국음향학회 2000년도 학술발표대회 논문집 제19권 2호
• /
• pp.235-238
• /
• 2000

Current diesel engines are usually equipped with turbochargers for improving fuel economy as well as meeting more stringent emission regulations. These turbochargers usually cause noise problems because they spins vey high such as 100,000 to 200,000 rpm, These noises are largely divided into whistle and whine noises. The frequency of whistle noise corresponds to their rotation speed, and the frequency of whine noise does to the multiplication of their rotation speed and the number of compressor blades. Turbocharger manufacturers developed a special type of compressor, effectively compressing air sucked from a duct; Recirculation Compressor Cover (RCC) or Map Width Enhancement (MWE). This special structure improves turbocharger's capability by expanding compressor's working area, but it seriously causes a noise problem, whine noise. There were many trials to surpress the noise occurred inside a compressor such as modification of a compressor, noise baffles or secondary measurements. However, it was currently concluded that the whine noise caused by the special compressor can not be reduced to that done by a standard compressor, and the strength difference of whine noises between the two compressors is not negligible. Thus, the standard compressor is decided to be applied to a newly developing heavy-duty diesel engine in order to resolve the turbocharger noise problem with a stiffened suction duct directly connected to a compressor.

• 한국자동차공학회논문집
• /
• 제24권5호
• /
• pp.549-555
• /
• 2016

This research was performed to determine the oil separation characteristics of the specially designed oil filter installed in a PCV cylinder head passage. The oil filter was specially designed with fleece for separating oil mist from blow-by gas. The fleece, made of fiber fabric material, is placed in the oil filter case to absorb oil mist with a small pressure drop during blow-by gas through the filter. To do this, 3-D CFD analysis was simulated for the simplified PCV system with the oil filter using the commercial code, Ansys CFX. Results showed that the oil filter's efficiency with fleece sharply increased as oil droplet size increased.

• 한국자동차공학회논문집
• /
• 제24권1호
• /
• pp.53-58
• /
• 2016

Modeling of engine coolant temperature was conducted for a series hybrid powertrain system. The purpose of this modeling was a simplification of complex heat transfer process inside a engine cooling system in order to apply it to the vehicle powertrain simulation software. A basic modeling concept is based on the energy conservation equation within engine coolant circuit and are composed of heat rejection from engine to coolant, convection heat transfer from an engine surface and a radiator to ambient air. At the final stage, the coolant temperature was summarized as a simple differential equation. Unknown heat transfer coefficients and heat rejection term were defined by theoretical and experimental methods. The calculation result from this modeling showed a reasonable prediction by comparison with the experimental data.

• 한국자동차공학회논문집
• /
• 제15권1호
• /
• pp.99-105
• /
• 2007

It is very important to clarify the 3-D angular flow characteristics of in-cylinder bulk motion in the developing process of variable induction system. In-cylinder flow induced by variable induction system is very complex, so we can not describe the in-cylinder bulk flow characteristics using the conventional swirl or tumble coefficient. In this study, we introduced the new 3-D angular flow index, angular flow coefficient($N_B$), for in-cylinder bulk flow characteristics. And also, to confirm the index, we carried out the steady flow rig test for intake port of test engine varying valve lift on the test matrix.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.193-198
• /
• 2004

In order to keep the market competitiveness, it is desirable for automotive manufacturer to meet the customer's various aspects of requirements. The overall NVH (Noise, Vibration, and Harshness) performance has been an important measure when evaluating overall vehicle performance, product quality, and enhancing customers' loyalty to the product. The noise and vibration, while the engine is idling, has been brought particular attention to the drivers and passengers, because they encounter the operation conditions quite frequently without other masking noise sources: wind noise, road noise, and even powertrain radiated noise at higher speed driving. The specific noise, defined as 'CHIT' noise, has been identified as a potential customer issue, from the Pickup Truck with newly developed V8 powertrain. This paper describes the definition of the noise, identifying the potential sources, and noise radiation mechanisms, based on series of powertrain and vehicle test and verification processes. Then, based on the root-cause identified, the design change has been proposed and validated with several vehicles in order to have a complete satisfaction of the customer.

• 대한기계학회논문집B
• /
• 제36권2호
• /
• pp.217-224
• /
• 2012

비도로용 차량의 경우 대부분 디젤엔진을 사용하여 엔진의 특성상 PM과 NOx의 배출이 많은 단점이 있다. 승용 및 상용 디젤 차량의 경우 CRDI 및 후처리 장치를 적용하였고 후처리 장치로 DOC/DPF를 장착함으로써 PM은 약 90% 이상 저감 가능하다. 상반관계인 NOx는 EGR 사용을 통해 1차적으로 NOx 배출량을 감소시키고 LNT, LNC, Urea-SCR 등의 DeNOx 시스템으로 NOx의 배출량을 보다 현저히 저감시켜 배기규제를 만족시키고 있다. 본 연구에서는 tier 4 interim 배기규제를 만족하기 위해 56kW급 오프로드 차량으로 연구를 진행하였다. NOx의 감소를 위해 WGT와 전자 제어방식의 HPL EGR 시스템을 적용하였고 CO와 THC, PM 배출가스를 줄이기 위해 DOC와 DPF를 사용하였다. EGR 시스템을 적용하기 위해 각 조건에 대한 기본 실험을 실시하여 EGR map을 작성하였다. 작성된 map을 NRTC 모드에서 시험하여 map의 적용성을 검증하고 tier 4 interim 배기규제 만족여부를 파악하였다.

• International Journal of Automotive Technology
• /
• 제4권1호
• /
• pp.47-55
• /
• 2003

The Center for Transportation Research at the Argonne National Laboratory (ANL) supports the DOE by evaluating advanced automotive technologies in a systems context. ha has developed a unique set of compatible simulation tools and test equipment to perform an integrated systems analysis project from modeling through hardware testing and validation. This project utilized these capabilities to demonstrate the trade-off in fuel economy and Oxides of Nitrogen (NOx) emissions in a so-called ‘pre-transmission’ parallel hybrid powertrain. The powertrain configuration (in simulation and on the dynamometer) consists of a Compression Ignition Direct Ignition (CIDI) engine, a Continuously Variable Transmission (CVT) and an electric drive motor coupled to the CVT input shaft. The trade-off is studied in a simulated environment using PSAT with different controllers (fuzzy logic and rule based) and engine models (neural network and steady state models developed from ANL data).

• 한국자동차공학회논문집
• /
• 제17권2호
• /
• pp.165-170
• /
• 2009

Pressure ripple, vibration and noise level are measured in each parts of the power steering system. MD(Mahalanobis Distance) is calculated by using MTS(Mahalanobis Taguchi System) with measured data, and noise sensitive components are selected. The components applied detail design parameters are made and data is measured. After that MD is calculated also. Mean value and SN ratio can be obtained from the MD. Effective noise reduction technique and dominant design parameters in hydraulic power steering system are introduced.

• 한국자동차공학회논문집
• /
• 제12권2호
• /
• pp.148-159
• /
• 2004

This paper discusses vibration mode of the drivesystem considered the vehicle body's dynamic characteristics to study the influence of the vehicle body's dynamic characteristics on the vibration mode of the engine mount system and the ride quality of a vehicle. The simulation model consists of the engine mount system, the powertrain and the rigid or elastic vehicle body. Variables used in this study are the stiffnesses of an engine mount system and the excitation forces. The Goals of the study are analyzing both the vibration transmitted to the vehicle body including the drivesystem and the influence of the vehicle body's dynamic characteristics on the engine mount system. The mode of drivesystems with a rigid and a elastic vehicle body was compared. From the result of the forced vibration analysis for the drivesystem with a elastic vehicle body, it is shown that the vehicle body's dynamic characteristics influence on the engine mount system reciprocally.