• 한국자동차공학회논문집
• /
• 제20권2호
• /
• pp.123-134
• /
• 2012

A typical cooling system of an engine relies on a water pump that circulates the coolant through the system. The pump is typically driven by the crankshaft through a mechanical link with engine starting. In order to reduce the friction and warm-up time of an engine, the clutch-type water pump (CWP) was applied in 2.0 liter diesel vehicle. The clutch-type water pump can force cooling water to supply into an engine by the operation of an electromagnetic clutch equipped as the inner part of pump system. The onset of CWP is decided by temperature of cooling water and engine oil. And, the control logic for an optimal operation of the clutch-type water pump was developed and applied in engine and vehicle tests. In this study, the warm-up time was measured with the conventional water pump and clutch-type water pump in engine tests. And the emission and the fuel consumption were evaluated under NEDC mode in vehicle tests. Also, tests were carried out for the various temperature conditions starting the operation of CWP. From the results of the study, the application of CWP can improve the fuel consumption and $CO_2$ reduction by about 3%.

• 한국자동차공학회논문집
• /
• 제24권4호
• /
• pp.480-486
• /
• 2016

Manufacturers have been applying several technologies that can improve the fuel economy of their cars. The regulated voltage control(RVC) system, is one of those technologies being used in passenger cars. In RVC, the voltage of an alternator is controlled depending on the electrical load demand or battery SOC, although each manufacturer differs from another in terms of detail. RVC can reduce the load of an alternator by consuming the stored energy of a battery and simultaneously generate energy. In this paper, a diesel passenger car equipped with an RVC system was tested under FTP-75 and HWFET modes to evaluate fuel economy as their initial battery SOC(100, 90, 80 and 60 %). The test results showed that the initial SOC affects fuel economy only under the FTP-75 mode. FTP-75 fuel economy of the 60% SOC was 13.2 % lower than the 100 % SOC. Also, the simultaneous consumption of the two energy sources did not appear in 60 % SOC.

• 한국자동차공학회논문집
• /
• 제17권1호
• /
• pp.19-23
• /
• 2009

This paper focuses on vehicle fuel economy improvement using D-Range neutral control of automatic transmission. The system objected to reducing of fuel consumption during idle. Usually, turbine of conventional auto transmission is mechanically linked to wheel during idling condition. Therefore speed ratio of torque converter is zero for that period. This causes needless power loss by the torque converter slip. To improve this inefficiency automobile makers develops electronically-controlled D-range neutral control system. The D-range neutral control system minimizes slip on the torque converter by shifting gear to a neutral position during vehicle stoped with D-range gear position. However there's insufficient study about the effect of D-range neutral control system on vehicle fuel economy. In this paper, researches are performed on effect of D-range neutral control system on vehicle fuel economy by experiment with two different vehicle. And it is also estimated the effect on vehicle fuel economy using computer simulation. As a result, 1.8% of LA-4 mode fuel economy improvement can be achieved in a vehicle by D-range neutral control system.

• 전자공학회논문지
• /
• 제54권6호
• /
• pp.117-122
• /
• 2017

전기자동차 파워트레인에서 발생되는 소음은 주로 모터의 전자기력 불균형에서 오는 소음과 기어 장치의 기계 시스템에서 발생되는 소음으로 구분될 수 있다. 이 소음들은 일반적 연소 엔진음 보다는 작지만, 조용한 배경 소음 때문에 더 거슬리는 소리가 될 수 있음에도 불구하고 그 소음의 특성이나 저감 방법은 널리 알려져 있지 않다. 본 논문에서는 전기차 개발단계 혹은 완성단계에서 적용할 수 있는 전달 경로에 감쇠 수동형 패치를 부착하여 소음을 저감하는 방법을 제시하고자 한다. 먼저, 모터 소음은 모터의 동적 특성에 따라 영향을 받으며 또한 모터 토크와 어떠한 상관성을 가지는 지를 보여준다. 또한, 모터 보다는 감속기의 표면이 더 소음에 취약한 부위라는 사실을 실험적으로 보여준다. 마지막으로, 주요 소음 전달경로인 드라이브 샤프트나 감속기 하우징 표면에 패치를 부착하여 실차 평가하였으며 실험 결과는 가속보다는 감속 조건에서 소음이 저감되는 영향이 크다는 것을 보여준다.

• 해양환경안전학회지
• /
• 제25권7호
• /
• pp.968-973
• /
• 2019

본 논문에서는 선박용 디젤엔진의 미세먼지저감 장치에 장착된 다공판 및 믹서의 형상과 배치에 따른 압력강하와 유동균일도 특성에 대한 연구를 진행하였다. 미세먼지저감 장치에 장착된 다공판 및 믹서는 미세먼지저감 장치 내의 배출가스 및 산화/환원제의 유동균일도를 높여 배출가스 저감 성능을 높이는 긍정적인 효과와 함께 시스템의 배압을 상승시키는 부정적인 효과도 동시에 지니고 있다. 본 연구에서는 5개의 다공판, 1개의 믹서를 Case 별로 조합하여 6개의 사양에 대해서 유동해석을 통해 각각 유동균일도 및 압력 강하를 계산하였으며, 최적의 다공판 및 믹서의 형상과 배치를 선정하였다.

• 융복합기술연구소 논문집
• /
• 제2권1호
• /
• pp.24-30
• /
• 2012

In this study, the trucks(2.9-liter) have been developed to use DME as fuel, and performance test of the vehicle's DME engine, power, emissions, fuel economy and vehicle aspects was conducted. For experiments, the fuel system(common-rail injectors and high-pressure pump included) and the engine control logic was developed, and ECU mapping was performed. As a result, the rail pressure from 40MPa to approximately 65% increase compared to the base injector has been confirmed that. Also, the pump discharge flow is 15.5 kg/h when the fuel rail pressure is 400rpm(40 MPa), and the pump discharge flow is 92.1 kg/h when the fuel rail pressure is 2,000rpm(40MPa). The maximum value of full-load torque capability is 25.5kgfm(based on 2,000rpm), and more than 90% compared to the level of the diesel engine were obtained. The DME vehicle was developed in this study, 120 km/h can drive to the stable, and calculated in accordance with the carbon-balance method of fuel consumptions is 5.7 km/L.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2009년도 추계학술대회
• /
• pp.98-101
• /
• 2009

최근에는 차량 진단을 위한 방법으로 차량 내 네트워크 방식이 사용되고 있으며, CAN(Controller Area Network), MOST, LIN, FlexRay와 같은 차량 프로토콜의 사용 증대로 인해 차량에 대한 분산 제어와 원하는 데이터를 실시간 모니터링 하기 위한 방법들이 모색되고 있다. 현재의 자동차의 경우 자가진단 점검단자인 OBD2(On Board Diagnostics)표준 DLC(Data Link Connector)커넥터를 이용한 진단용 모듈(스캐너)을 통해 차량을 진단 한다. 그러나 엔진과 동력전달 계통(Powertrain) 부분으로 진단이 국한되어 있고, 사용자 측면을 고려하지 못하였다. 따라서, 본 논문에서는 Ethernet port를 이용한 차량 진단 모니터링 시스템을 설계하여 CAN 프로토콜 차량 데이터를 송수신하고 PC를 이용하여 보다 간편하게 차량의 상태와 정보를 제공하고 진단할 수 있는 모니터링 시스템을 구현한다.

• 한국가스학회지
• /
• 제25권2호
• /
• pp.28-33
• /
• 2021

최근 친환경 자동차에 대한 관심이 높아짐에 따라 공해물질을 배출하지 않는 수소연료전지 차량에 대한 관심과 구매가 증가하고 있다. 최근 정부의 수소에너지 보급정책에 따라 수소충전소의 확충과 핵심부품의 국산화를 지원하고 있다. 본 연구에서는 그중에서도 수소 유량제어 밸브의 차압에 따른 유동특성을 연구하였다. 차압이 높아 짐에 따라 질량유량과 유량계수는 체적유량과 다른 경향을 보임을 확인하였다. 그리고 병목 구간에서의 노즐효과로 인해 수소온도에 영향을 주게되고, 밀도의 변화를 일으켜 질량유량에 영향을 주게 되는 것을 확인 하였다.

• 농업과학연구
• /
• 제46권3호
• /
• pp.613-627
• /
• 2019

The purpose of this study was to design a powertrain for a 78 kW AWD (all wheel drive) electric tractor by analyzing the combination of various reduction gear ratios on a commercial motor using data from actual agricultural work and driving conditions. A load measurement system was constructed to collect data using wheel torque meters, proximity sensors, and a data acquisition system. Field experiments for measuring load data were performed for two environmental driving conditions (on asphalt and soil) and four agricultural operations (plow tillage, rotary tillage, loader operation, and baler operation). The attached implements and gear stages were selected through farmer surveys. The range of the reduction ratio was determined by selecting the minimum reduction ratio needed to satisfy the torque condition required for agricultural operations and the maximum reduction gear ratio to satisfy the maximum travel speed. The minimum reduction gear ratio selected was 57 in consideration of the working load condition and the maximum reduction gear ratio selected was 62 considering the maximum running speed. In the range of the reduction gear ratio 57 - 62, the selected motor satisfied all working torque conditions. As a result, the combination of the selected motor and reduction gear ratio was applicable for satisfying the loads required during agricultural operation and driving operation.

• Journal of Mechanical Science and Technology
• /
• 제16권7호
• /
• pp.882-888
• /
• 2002

In this paper, an algorithm to increase the shift speed is suggested by increasing the line pressure for a metal belt CVT. In order to control the shift speed, an algorithm to calculate the target shift speed is presented from the modified CVT shift dynamics. In applying the shift speed control algorithm, a criterion is proposed to prevent the excessive hydraulic loss due to the increased line pressure. Simulations are performed based on the dynamic models of the hydraulic control valves, powertrain and the vehicle. It is found from the simulation results that performance of the engine operation can be improved by the faster shift speed, which results in the improved fuel economy by 2% compared with that of the conventional electronic control CVT in spite of the increased hydraulic loss due to the increased line pressure.