• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.2
• /
• pp.115-122
• /
• 2008

Mostly used sensors have wired powering and two-way cable systems. It is difficult to employ wired sensor network in ubiquitous era because of a number of sensors and cables. Therefore, sensor networks move from wired systems to wireless systems for the future. However, the power source is a critical obstacle for wireless sensornodes. This research represents the new power source which supplies energy sensor node, maintains over 10 years, and thus replaces batteries with limit of lifetime. The system with piezo materials scavenges extra energies such as vibration and acceleration from the environment. Then it converts the scavenged mechanical energy to electrical energy for powering a sensor, a controller and a circuit for regulating voltage and transmitting sensor value. This study explains the properties of piezo material through theoretical analysis and experiments, and demonstrates powering sensor and transmitting data with stored energy (35mJ) for 14 sec. The developed system provides a solution to overcome the critical problem of making up wireless sensor networks.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.5
• /
• pp.376-379
• /
• 2021

The design and performance of a SiC-MOSFET-based 11-kW bi-directional on-board charger (OBC) for electric vehicles is presented. The OBC consists of a three-phase two-level AC/DC converter and a CLLLC resonant converter. All the power devices are implemented with SiC-MOSFETs to reduce the conduction losses generated in the OBC, and the DC-link voltage is designed to track the level of battery voltage in the forward and reverse powering modes. As a result, the CLLLC resonant converter always runs at the switching frequency near the resonant frequency, resulting in high-efficiency operation at the maximum powering modes. As the DC-link voltage varies according to the battery voltage, the AC/DC converter in the proposed OBC adopts an adaptive DC-link voltage controller. The performance of the proposed 11-kW OBC is verified by a prototype converter with the following specifications: three-phase 60-Hz 380-V input, 11-kW capacity, and battery voltage range of 214-413-V, resulting in the conversion efficiency of over 95.0-% in the forward and reverse powering modes.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.278-291
• /
• 2021

This paper applies load variation method to predict speed-power-rpm relationship along with propulsive performances in regular head waves, and to derive overload factors (ITTC, 2018). 'Calm-water tests' and 'resistance test in waves' are used. The modified overload factors are proposed taking non-linearity into consideration, and applied to the direct powering, and resistance and thrust identity method. These indirect methods are evaluated through comparing the speed-power-rpm relationships with those obtained from the resistance and self-propulsion tests in calm water and in waves. The objective ship is KVLCC2. The load variation method predicts well the speed-power-rpm relationship and propulsion performances in waves. The direct powering method with modified overload factors also predicts well. The resistance and thrust identity method with modified overload factor predicts with a little difference. The direct powering method with overload factors predicts with a relatively larger difference.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.22 no.2
• /
• pp.35-48
• /
• 1985

The present work develops a method of evaluating thrust deduction and wake for different loads of the propeller using the concerted application of the theoretical tools and experimental techniques. It also shows the applicability of the new method to the design of optimum hull form. Firstly, the problem of hull-propeller interaction was analyzed in terms of inviscid as well as viscous components of the thrust deduction and wake. The wavemaking resistance of a hull and propeller were mathematically represented by sources on the hull surface and sink on the propeller plane, respectively. The strength of sink was determined by utilizing the radial distributions of propeller load and nominal wake. The resistance increment due to a propeller and the axial perturbation flow induced by the hull in the propeller plane were calculated. Especially, the inviscid component of the thrust deduction was calculated by subtraction the wavemaking resistance of a bare hull, the wavemaking resistance of a free-running propeller and the augmentation of propeller resistance due to hull action from the wavemaking resistance of the hull with a propeller. The viscous components of the thrust deduction and wake were estimated as functions of propeller load which were established by the propeller load varying test after deduction the calculated inviscid components. Secondly, an analysis method of powering performance was developed based on the potential theory and the propeller load varying test. The hybrid method estimates the thrust deduction, wake and propeller open-water efficiency for different propeller load. This method can be utilized in the analysis of powering performance for the propeller load variation such as the added resistance due to hull surface roughness, the added resistance due to wind, etc. Finally, the hybrid method was applied to the optimum design of hull form. A series of afterbody shapes was obtained by systematically varying the waterplane and section shapes of a parent afterbody without changing the principal dimensions, block coefficient and prismatic coefficient. From the comparison of the predicted results such as wavemaking resistance, thrust deduction, wake and delivered power, an optimum hull form was obtained. The delivered power of the optimized hull form was reduced by 5.7% which was confirmed by model tests. Also the predicted delivered power by the hybrid method shows fairly good agreement with the test result. It is therefore considered that the new analysis method of powering performance can be utilized as a practical tool for the design of optimum hull form as for the analysis of powering performance for the propeller load variation in the preliminary design stage.

• 한국기계연구소 소보
• /
• s.9
• /
• pp.133-140
• /
• 1982

• Proceedings of the Korea Inteligent Information System Society Conference
• /
• 2002.11a
• /
• pp.3-14
• /
• 2002

• Bulletin of Food Technology
• /
• v.23 no.4
• /
• pp.561-565
• /
• 2010

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.17-21
• /
• 2001

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.473-475
• /
• 1996

In this paper, bilateral variable-ratio dc chopper system for electric vehicle is proposed. We present the method which is able to simplify the main synthetic chopper circuit by selecting among the forward powering, forward regenerative braking, backward powering, and backward regenerative braking only by control signal. By conducting the experiment with separately excited dc motor, it is confirmed that two quadrant chopper can drive four quadrant operation.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.7
• /
• pp.2356-2366
• /
• 1996

High-power electronic chips have been advanced to such an extent that the heat dissipation capability of a system design has become one of the primary limiting factors. Therefore, thermal design must be considered in the early stage of the electronic system development. In present paper, the results of an experimental study on the forced convection cooling are presented to evaluate cooling performance of an electronic cabinet which in generally used for telecommunication system. Temperatures and thermal resistances are applied to compare the heat transfer characteristics for various locations of a fan unit as well as various configuration of non-uniform powering modules. As a result, the optimal configuration of a fan unit and powering configuration is suggested for the effective thermal design of telecommunication system.