• 한국철도학회논문집
• /
• 제7권1호
• /
• pp.60-64
• /
• 2004

Harmonic current originating from electric locomotives can be magnified due to the impedance characteristics of power supply circuit and bring about various problems. That is, electromagnetic interference with communication lines, operational trouble in signaling, overheat and/or vibration in power capacitor, mis-operation in protection relay and so on. Therefore, the exact assessment of the harmonic current flow must be undertaken at design and planning stage for the electric traction systems. for these reasons, this study propose a new approach to model and to analyse traction power feeding system focused on system response to current and voltage harmonic(PART I). Measurements of harmonics are also performed for railway power supply systems under normal operation. Spectrum and distortion analyses in measurement data are variously described in PART II.

• International Journal of Precision Engineering and Manufacturing
• /
• 제7권1호
• /
• pp.18-23
• /
• 2006

Cutting by a high speed laser cutting machine is one of most effective technologies to improve productivity. This paper has presented the cutting characteristics and optimal cutting conditions in a high speed feeding type laser cutting machine by using Tacuchi method in the design of experiment. An L9(34) orthogonal array is adopted to study the effect of adjustment parameters. The adjustment parameters consist of cutting speed, laser power, laser output duty and assistant gas pressure. The surface roughness of sheet metal is regarded as a quality feature. Analysis of variance is performed in order to evaluate the effect of adjustment parameters on the quality feature of laser cutting process.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 연구회 합동 학술발표회 논문집
• /
• pp.18-22
• /
• 1998

A PWM inverter with an induction motor often has a problem with a high frequency leakage current that flows through stray capacitor between stator windings and a motor frame to ground. This paper presents an equivalent circuit for high frequency leakage currents in PWM inverter feeding an induction motor, which forms an LCR series resonant circuit. A conventional common mode ckoke or reactor in series between the ac terminals of a PWM inverter and those of an ac motor is not effective to reduce the rms and average values of the leakage current, but effective to reduce the peak value. Furthermore, this paper proposes a leakage current damper which is different in damping principle from the conventional common mode choke. It is shown theoretically and experimentally that the leakage current damper is able to reduce the rms value of the leakage current to 25%, where the core used in the leakage current damper is smaller than that of the conventional common-mode choke

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1820-1823
• /
• 2003

A high speed feeding type laser cutting M/C is developed for precise cutting of sheet metal. This paper has been carried out to obtain cutting characteristics and optimal cutting conditions of the developed high speed feeding type laser cutting M/C by a design of experiments. Cutting speed. laser power. laser duty and gas pressure are control factors for the surface roughness. The major factors affecting the surface roughness and the optimum cutting conditions are studied with minimum experiments using Taguchi method.

• 한국결정성장학회지
• /
• 제4권2호
• /
• pp.111-118
• /
• 1994

Crystal growth chamber 상부에 있는 reservoir에서 polycrystalline silicon powder를 연속적으로 feeding하면서 도가니 하부에 용융대를 형성시키고 seed를 meed를 dipping하여 회전시키면서 하부로 끌어내려 단결정을 성장시키는 연속성장법의 기본 원리를 확립하였고, 직접 고안 설계 제작한 연속성장 장치로 silicon 단결정을 성장시켰다. 본 연속성장법은 melt에 미치는 중력, 진동, melt의 표면장력, melt와 solid의 계면 장력, seed의 회전에 따른 원심력 등의 힘들이서로 상쇄되고 power, feeding양과 성장속도가 비례하여 적당한 조합을 이룰 때 안정한 연속성장을 할 수있다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.464-469
• /
• 1998

In the conventional wire feeder drives of welding machine, one thyristor or MOSFET device was used for half-wave phase control circuit and direct EMF measurement was used for sensing the wire feed rate. But the method using one switching device has poor response for sudden disturbance and it has latent speed ripple. It can affect some welding performance such as spatter generation and irregular bead formming. Therefore, the welding performance using full-bridge PWM speed control scheme was compared with conventional driving scheme was compared with conventional driving scheme and experimented in this paper. The results of experiment confirm the posibility of welding performance improvement by proposed constant speed control scheme in wire feeding drive of welding machine.

• 대한전자공학회논문지
• /
• 제19권4호
• /
• pp.6-14
• /
• 1982

난·시청지역 해소를 위한 소출력 방송국의 출력 증가시 동일 채널의 다른 방송국가의혼신을 막기 위하여 트정 방향의 전계 강도를 감소시켜야 할 경우 현재 안테나에 대한 배향성 조정이 불가피하게 된다. 본 연구는 이러한 경우 단지 급전선의 길이에 의한 급전점의 위상 조정에 의하여 임의의 방향에 대한 전계 강도를 조절하는 방법에 대하여 연구한 것이다.

• 한국전자파학회논문지
• /
• 제8권6호
• /
• pp.363-644
• /
• 1997

본 논문에서는 그라운드변 상의 개구를 통해 마이크로스트립 패치로 결합을 일으키는 구조를 갖는 PCS 기지 국용 정형 빔 배열 안테나 설계와 제작에 관하여 다룬다. 최적의 정형 빔 패턴은 안테나 합성법으로 얻어졌다. 배 열된 패치들 사이에서의 결합을 고려한 배열 안테나와 급전회로는 CAD tool을 이용하여 설계되었다. 급전 회로 는 최적의 정형 빔 패턴을 얻기 위해서 Wilkinson 전력 분배기를 이용하여 설계되었다. 설계 결과와 측정 결과가 비교되어진다.

• 한국정밀공학회지
• /
• 제21권6호
• /
• pp.77-83
• /
• 2004

Cutting by a high speed laser cutting machine is one of most effective technologies to improve productivity. This paper has studied to obtain the cutting characteristics and optimal cutting conditions in a high speed feeding type laser cutting machine by Tacuchi method in design of experiments. A Lf(34) orthogonal array is adopted to study the effect of adjustment parameter. The adjustment parameters consist of cutting speed, laser power, laser output duty and assistant gas pressure. And the quality feature is selected as surface roughness of sheet metal. Variance analysis is performed in order to evaluate the effect of adjustment parameters on the quality feature of laser cutting process.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.614-615
• /
• 2007

There are roughly a hundred types of cables in power plants. The distribution of circuits in a nuclear plant is comprised of 20% instrument cables, 61% control cables, 13% AC power cables, 1% DC power cables, and 5% communication lines. In the nuclear power plant, medium voltage cables are generally included in the scope of systems reviewed for safety and are included in a plant's maintenance program. Medium voltage cables provide power to many critical components in plants, including feed water pumps, circulating water pumps, and condensate pumps. Among these cables, high temperature sections of cables feeding electrical power to the circulating water pump and the condenser extraction pump were found. The evaluation for these cables is performed to find the maximum allowable current and temperature. The result shows that the load current flowed about 85% of the allowable current ampacity, and the temperature of conductor at full load current did not exceed the limited temperature. Therefore, existing cables for circulating water pump and condenser extraction pump system are going to be used during design life.