• Journal of Electrical Engineering and Technology
• /
• v.8 no.4
• /
• pp.920-929
• /
• 2013

Within the project 'e performance' supported by the German Ministry of Education and Research (BMBF) an electric vehicle, powered by two lithium-ion battery packs of different capacity and voltage has been developed. The required Energy Management System (EMS) in this system controls the current flows of both packs independently by means of two individual dc-dc converters. It acts as an intermediary between energy storage (battery management systems-BMS) and the drivetrain controller on the vehicle control unit (VCU) as well as the on-board charger. This paper describes the most important tasks of the EMS and its interfaces to the BMS and the VCU. To validate the algorithms before integrating them into the vehicle prototype, a detailed Matlab / Simulink-model was created in the project. Test procedures and results from the simulation as well as experiences and comparisons from the real car are presented at the end.

• Current Optics and Photonics
• /
• v.8 no.4
• /
• pp.421-426
• /
• 2024

The use of stimulated emission depletion (STED) microscopy has significantly improved resolution beyond the limits imposed by diffraction; Furthermore, STED microscopy adopts a 4Pi-geometry to achieve an isotropic improvement in resolution. In isoSTED microscopy, a polarizing beam splitter and retarders are used in a 4Pi cavity to split beams of identical power, generating constructive and destructive interference for lateral and axial resolution improvements, respectively. The precise alignment of the retarders is crucial for optimizing the performance of isoSTED microscopy, because this orientation affects the quality of the depletion focus, necessitating zero intensity at the center. Incomplete destructive interference can lead to unwanted fluorescence inhibition, resulting in degraded resolution and contrast. However, measuring the intensity and polarization state in each optical path of the 4Pi cavity is complex and requires additional devices such as a power meter. Here, we propose a simple and accurate alignment method for the 4Pi cavity in isoSTED microscopy. Our approach demonstrates the equal allocation of power between upper and lower beam paths and achieves complete destructive interference using a polarizing beam displacer and a single CCD camera positioned outside the 4Pi cavity.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.51 no.9
• /
• pp.433-440
• /
• 2002

The addition of switches to a distribution feeder does, in general, increase reliability by decreasing the duration of the outage of many to the customers on the feeder. To cover its service area so that feeder-level delivery reaches sufficiently close to all customers, feeders typically split their routes many times, in what is often called a lateral feeder. It is interesting to note, however, that the effectiveness of a switch is very much dependent on the types of lateral feeder. The types of lateral are classified into two types. The first is loop lateral feeder that can connect its load to an adjacent feeder through a tie line in case that a fault occurs in its feeder and it is laid out so that every feeder has complete fault backup through re-switching of its loads to other sources like a main feeder The second is the radial lateral feeder cannot connect its load to an adjacent line, no provision is made for contingency backup of feeders. There are no other circuits in the radial lateral feeder form which to restore power. In this study, we evaluate the effectiveness of a switch installation between on the radial and loop lateral feeders to increase reliability by decreasing the duration of the outage. These results can help power utility to design the switch layouts on the radial and loop lateral feeder system.

• Journal of the Korean Society of Safety
• /
• v.36 no.5
• /
• pp.10-17
• /
• 2021

The controversy over the risk of the human body being affected by electromagnetic fields emitted from 60 Hz power lines continues without end. There are currently no new studies or research progress being made in this direction that is notable, and the number of civil complaints is gradually increasing. The problem is that each study produces different results, among which the effect of exposure to magnetic fields on childhood leukemia is a major one. In Korea, an electrician who was maintaining a 22.9 kV power line died of leukemia, which has recently been recognized as an occupational disease. Methods to reduce magnetic fields from power lines include shielding with wire loops, incorporating split phases and compaction techniques, installing underground power lines, converting to high-voltage direct current (HVDC), and increasing the ground clearance of transmission towers. Depending on whether a separate power supply is needed or not, there are two types of wire loops: passive loop and active loop. Magnetic field reduction is currently done through underground power lines; however, the disadvantage of this process is high construction costs. Installing passive loops, with relatively low construction costs, leads to lower magnetic field reduction rates than installing underground cables and a weakness to not solving the landscape problem. This methodological study aims at designing methods and reducing the effects of 2-wire set loops-the simplest and most practical. Since the method proposed in this study has been designed after analyzing the distribution of complex electromagnetic fields near the expected loop installation location, a practical design can be implemented without the need for any difficult optimization programming.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.4
• /
• pp.271-274
• /
• 2013

Power Metal Oxide Semiconductor Field Effect Transistor's (MOSFETs) are well known for superior switching speed, and they require very little gate drive power because of the insulated gate. In these respects, power MOSFETs approach the characteristics of an "ideal switch". The main drawback is on-resistance RDS(on) and its strong positive temperature coefficient. While this process has been driven by market place competition with operating parameters determined by products, manufacturing technology innovations that have not necessarily followed such a consistent path have enabled it. This treatise briefly examines metal oxide semiconductor (MOS) device characteristics and elucidates important future issues which semiconductor technologists face as they attempt to continue the rate of progress to the identified terminus of the technology shrink path in about 2020. We could find at the electrical property as variation p base dose. Ultimately, its ON state voltage drop was enhanced also shrink chip size. To obtain an optimized parameter and design, we have simulated over 500 V Field ring using 8 Field rings. Field ring width was $3{\mu}m$ and P base dose was $1e15cm^2$. Also the numerical multiple $2.52cm^2$ was obtained which indicates the doping limit of the original device. We have simulated diffusion condition was split from $1,150^{\circ}C$ to $1,200^{\circ}C$. And then $1,150^{\circ}C$ diffusion time was best condition for break down voltage.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.1
• /
• pp.92-96
• /
• 2011

In this paper, we present a bandpass filter (BPF) based on composite right-/left-handed (CRLH) structure for improving the linearity of the power amplifier. The proposed BPF consist of the inter-digit signal line on the top plane and the complementary split ring resonator (CSRR) on the bottom plane, respectively. The insertion loss is minimized at operation frequency and the 2nd harmonic is suppressed by the bandpass filter using the CRLH structure, respectively. The output power of 33 dBm, the 2nd harmonic of -53.527 dBc, 3rd inter-modulation distortion of -36.16 dBc was obtained at 2.14 GHz, respectively. Compared with the reference power amplifier, the 2nd harmonic of 16 dB and 3rd inter-modulation distortion of 12 dB have been improved at 2.14 GHz, respectively.

• Wind and Structures
• /
• v.24 no.6
• /
• pp.579-611
• /
• 2017

Bora is a strong, usually dry temporally and spatially transient wind that is common at the eastern Adriatic Coast and many other dynamically similar regions around the world. One of the Bora main characteristics is its gustiness, when wind velocities can reach up to five times the mean velocity. Bora often creates significant problems to traffic, structures and human life in general. In this study, Bora velocity and near-ground turbulence are studied using the results of three-level high-frequency Bora field measurements carried out on a meteorological tower near the city of Split, Croatia. These measurements are analyzed for a period from April 2010 until June 2011. This rather long period allows for making quite robust and reliable conclusions. The focus is on mean Bora velocity, turbulence intensity, Reynolds shear stress and turbulence length scale profiles, as well as on Bora velocity power spectra and thermal stratification. The results are compared with commonly used empirical laws and recommendations provided in the ESDU 85020 wind engineering standard to question its applicability to Bora. The obtained results report some interesting findings. In particular, the empirical power- and logarithmic laws proved to fit mean Bora velocity profiles well. With decreasing Bora velocity there is an increase in the power-law exponent and aerodynamic surface roughness length, and simultaneously a decrease in friction velocity. This indicates an urban-like velocity profile for smaller wind velocities and a rural-like velocity profile for larger wind velocities. Bora proved to be near-neutral thermally stratified. Turbulence intensity and lateral component of turbulence length scales agree well with ESDU 85020 for this particular terrain type. Longitudinal and vertical turbulence length scales, Reynolds shear stress and velocity power spectra differ considerably from ESDU 85020. This may have significant implications on calculations of Bora wind loads on structures.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.6
• /
• pp.719-725
• /
• 2019

We propose a 2.4-GHz CMOS power amplifier (PA) with a bypass structure to improve the power-added efficiency (PAE) in the low-power region. The primary winding of the output transformer is split into two parts. One of the primary windings is connected to the output of the power stage for high-power mode. The other primary winding is connected to the output of the driver stage for low-power mode. Operation of the high power mode is similar to conventional PAs. On the other hand, the output power of the driver stage becomes the output power of the overall PA in the low power mode. Owing to a turning-off of the power stage, the power consumption is decreased in low-power mode. We designed the CMOS PA using a 180-nm RFCMOS process. The measured maximum output power is 27.78 dBm with a PAE of 20.5%. At a measured output power of 16 dBm, the PAE is improved from 2.5% to 12.7%.

• Korean Journal of Cognitive Science
• /
• v.1 no.2
• /
• pp.317-346
• /
• 1989

A congnitive shape decomposition method that agrees with human intuition is proposed for the conceptual recognition from sillouettes of objects. Descriptions specifying the structure of shape in terms of meaningful parts and relations have cognitive power and anthropomorphism. In general, man-made objects have a lot of collinear lines and regularity. For the cognitive decomposition of man-made objects, many heuristic rules based on the cognitive experimentation are applied on the context of collinerarity and regularity. The cognitive shape decomposition for the natural shape is carried out by analyzing the possible configuraitions of vertices and line segments for one concave vertex. A cost function for the configuation is designed by weighted sum of five criteria such as, the length of split line segment, the number of split line segments at concave vertex, the proximity of concave vertex, and the correspondence of vertices. These criteria are vased on the property of human perception such as proximtiy, symmetry, and simplicity. The most promising vertex os selected among three set of visible vertices by evaluating the cost function. A number of experiments conducted on the different types of shapes shows that the results correspond with human intuition.

• Journal of IKEEE
• /
• v.24 no.2
• /
• pp.592-597
• /
• 2020

Since SiC has 10 times higher breakdown field and 3 times higher energy gap than Si, it is possible to manufacture an excellent power MOSFET with a high breakdown voltage. However, since it has a high on-resistance due to low mobility, a Trench MOSFET has been proposed to lower it, but at the same time, it has a problem that BV decreases. The purpose of this paper is to design a 1200V trench MOSFET, and to solve this, split Epi depth, Trench depth, and Trench depth to Epi depth, which are important variables for BV and Ron, to achieve maximum electric field, BV, Ron's reliability characteristics were compared and analyzed. As the epi depth increased, the trench depth decreased, and the epi depth decreased at the trench depth, the maximum electric field decrease, BV increase, and Ron increase were confirmed. All results were simulated by sentaurus TCAD.