• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.362.2-362.2
• /
• 2016

본 실험은 CW (Continuous wave) 주파수를 가진 교류 자기장을 발생시켜 자성나노입자를 가열시키는 것이 목적이다. 이를 위해 CW 주파수 및 SMPS (Switching Mode Power Supply)를 이용해 코일에서 교류 자기장을 발생시키는 평판형 자기장 발생 장치를 자체적으로 개발하였다. 이를 이용하여 인가전압을 변화시키면서 자기장 세기의 변화를 주었다. 평판형 코일 위에는 유리 등의 원형 평판 절연체를 덮고 그 절연체 표면에 웰(Well plate)를 위치시켰고 그 안에 자성나노입자가 포함된 수용액을 넣어 교류 자기장에 노출시켰다. 자기장 측정센서(Magnetic pick up coil, Gauss Meter)를 이용하여 자기장의 세기를 측정하였고, 자성나노입자의 농도, 크기 및 자기장 세기에 따른 자성나노입자의 온도상승효과를 접촉식 온도계를 이용하여 정량적으로 측정하였다.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.933-938
• /
• 2001

A 5-valve(intake 3-valve) engine has been developed to increase engine performance. These vehicles have a high power caused by the decrease of inertia mass of an intake valve and the increase of intake effective area. In this study, velocity profiles at near intake valves were inspected by using a two-color PIV and laser sheet method with tumble control valve(TCV). In addition, steady flow tests were performed to quantify tumble ratio on flow-fields generated with a TCV. These experimental results show that the tendency of the tunble ratio in intake 3-valve engine is different from the one in intake 2-valve engine. From this results, the intake flow characteristics around intake valves were made clear.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.9
• /
• pp.69-74
• /
• 2011

In this paper, the UV corona camera was developed using the solar blind and Multi Channel Plate(MCP) technology for the target localization of UV image. UV camera developed a $6.4[^{\circ}]{\times}4.8[^{\circ}]$ of the field of view as a conventional camera to diagnose a wide range of slightly enlarged, and power equipment to measure the distance between the camera and the distance meter has been attached. UV camera to measure the discharge count and the UV image was developed, compared with a commercial camera, there was no significant difference. In salt spray environments breakdown voltage was lower than the normal state, thereby discharging the image was rapidly growing phenomenon.

• Journal of the Korean Institute of Navigation
• /
• v.19 no.3
• /
• pp.29-34
• /
• 1995

IEC and CISPR have continuously endeavored the measurement method of Immunity Test as international unification, but not established yet. The main reason is that the measurement method and the normalization of threshold to obtain the complicated parameters for Immunity Test are difficult. Thus, the Immunity Test Setups are used differently according to the measured electromagnetic environments. This study developed an Immunity Test System and Algorithm for measurement software suitable for IEC801-3 Regulatons using ready-made amplifier, signal generator, and developes interconnecting interface board interacting with other appratus i.e., RF Switch, Power Meter, Field Sensor and Pre-amp. We are to develope an automated software using Top/Down and OOP(Object Oriented Programming) method.

• Proceedings of the KIPE Conference
• /
• 2001.12a
• /
• pp.190-193
• /
• 2001

This paper describes the reduction of vibration and position error of Linear Pulse Motor(LPM) with the control method of PWM duty ratio by using Motion Controller in LPM. The LPM is operated on micro-stepping drive, that the linear scale is sequently returned the position signals of a micro-meter And next micro-step is controlled with the scale factor when position error is occurred. The scale factor is experimently acquired.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.6
• /
• pp.24-30
• /
• 2013

This paper studies the comparative analysis on two different internal cushion devices (the types of needle and relief valve) used to absorb the energy which is generated when the pneumatic cylinder moves with the load at meter-out speed control system. The effect at varying the piston velocity under same driving condition is mainly investigated. The simulation results on pressure in the cushion chamber and the dynamic behavior of the relief valve type cushion device are compared with the needle valve type. Design and performance are improved with the cushion configuration of better quality at high-speed pneumatic cylinder. Based on the relation between absorbed energy and impact energy at cushion process, cushion performance at pneumatic cylinder is evaluated.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.9
• /
• pp.1783-1787
• /
• 2011

The slip frequency is included in feature frequency for fault diagnosis of rotor bar, so rotating rotor speed is needed. In this study, rotor slot harmonic(RSH) method is suggested for speed estimation of induction motor. When the rotor is rotating, motor current signal include the harmonic signal of back-emf voltage related with number of rotor slot. So from the power spectrum of current signal, the rotor speed can be founded. This method of rotor speed estimation gives the slip frequency, and the feature frequency of rotor bar fault can be calculated. Comparing with stroboscope speed meter, the error rate of suggested method is less than 0.1[%].

• Journal of the Korean Society of Safety
• /
• v.19 no.4 s.68
• /
• pp.8-13
• /
• 2004

The purpose of this paper is to investigate the welding residual stress distribution according to the constraint or non-constraint welding condition with titanium commonly using power station, aircraft, and ship. The measuring method of the residual stress was applied stress release rating method with strain gages and a potable strain meter. The x direction residual stress generally showed the tensile residual stress in case of res03int welding. On the other hand, the x direction residual stress under non-restraint welding were changed tensile stress into compressive stress on 15mm away from welding bead center. Also, the y direction residual stress generally showed the tensile residual stress in case of non-restraint welding and the y direction residual stress under restraint welding were changed tensile stress into compressive stress about 60mm away from welding bead center.

• Proceedings of the KIEE Conference
• /
• 2006.07d
• /
• pp.1783-1784
• /
• 2006

A laser interferometer is the unique measurement device that can measure the range up to a few meters with sub-nano resolution and this characteristic makes it as the important sensing device for the emerging nano-mechatronics technologies. The laser interferometer, however, is very sensitive to the environments such as temperature, humidity, sound noises, vibrations and air turbulences and these factors result in a few hundred nano meter errors. There have been many efforts to reduce these environmental errors. The output of the laser interferometer is assumed to be the sum of a real displacement and a Markov process noise. The purpose of this paper is to develop Kalman filter algorithms to reduce the laser interferometer measurement errors by exploiting the information of displacements in position-servo systems.

• Journal of Ocean Engineering and Technology
• /
• v.24 no.1
• /
• pp.133-139
• /
• 2010

From the ancient times, there are waves in the ocean. And all the moving body have energy. We have a kind of hope to convert the wave energy into electric one. Finally we can find out a power generator mechanism that mainly use the principle of pulleys. We have made drawings for this and completed the wave energy converter. This wave energy converter consists of several pulleys, rope, generator, buoys and anchors. The distance between an anchor and buoy is changed according to the hight of waves. Several sets of anchors, pulleys and buoys can make the movement of rope, and the ropes wind up a converter axis. In case of 1 meter movement of the buoy, the winding distance will be amplified 2 or 3 times if we use several moving and fixed pulleys. Based on this concept, we developed 2 kind of prototypes. One is for the test in the laboratory and the other is for the field test. Through the two test, we could confirm the usability of this mechanism.