• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 연구회 합동 학술발표회 논문집
• /
• pp.9-12
• /
• 1998

In this paper, the power factor correction circuit using a parallel drive method is proposed so that the high power inverter air-conditioner with 3[ph] compressor motor may obtain the cost down and the improved performance. The adequate design procedures are presented to reduce the material costs by eliminating the power factor improving LC filter and derating output capacitor and inverter switches. Using the determined components, the prototype circuit with 6[kW] power consumption is built and tested to verify the operation of the proposed circuit.

• 전자공학회논문지S
• /
• 제35S권8호
• /
• pp.113-119
• /
• 1998

무전극 램프의 점등은 램프 양단에 고주파를 갖는 고전압을 인가해야 한다. 종래의 무전극 램프의 구동 회로로 선형 증폭기가 이용되어져 왔으나, 낮은 에너지 변환 효율로 인해 PWM 스위칭 방식의 인버터로 교체되고 있다. 그러나 고주파 스위칭시 인버터의 스위칭 소자에서 스위칭 손실의 증가 및 노이즈 발생의 문제로 인해 PWM 인버터는 고주파 동작이 제한된다. 이러한 문제점을 해결하기 위해 영전압 스위칭 기술을 PWM 인버터에 적용하여 고주파 스위칭이 가능하게 하고, 또한 스위칭 손실과 노이즈 발생을 줄일 수 있다. 본 논문에서는 무전극 램프 구동회로로 영전압 스위칭 고주파 인버터에 대하여 동작 해석과 설계 지침 제시하였다. 또한, 실험을 통하여 해석된 결과의 타당성을 확인하였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2007년도 추계학술대회 논문집
• /
• pp.133-135
• /
• 2007

This research presented the new zero-current switching pulse width modulation SEPP(Single Ended Push-Pull)high frequency inverter for solving the problem of the zero-current SEPP high frequency inverter circuit which is using widely in the practical application of an induction heating apparatus, the soft switching operation and power control are impossible when the lowest power supply in the zero-current switching pulse width modulation SEPP high frequency inverter. The inverter circuit which is attempted by on-off operation of a switch has the reduction effect of the power loss due to a soft switching and a high frequency switching. And it confirmed that the power regulation is possible continuously from 0.25[kW] until 2.84[kW] in the case the duty rate(D) changes from 0.08 to 0.3 under zero-current switching operating by a dissymmetry pulse width modulating control and the power conversion efficiency comes true the efficiency of 95[%]. Due to the result above, the ZCS PWM SEPP high frequency inverter will be effective as sources of an induction heating apparatus.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.288-290
• /
• 2006

An efficiency improving method for Uninterruptible Power Supply System(UPS) was developed by using OP-AMP based application circuits such as voltage detection device, current detection device and static switch control device. The efficiency improving algorithm was made by mixing the operating concepts of On-Line type UPS with the operating concepts of Off-Line type UPS. The UPS' inverter does not work if the UPS' output load current is not higher than the low load operating current which is about 0-30(%) of the UPS' output load capacity. The low load operating current is adjustable within the half of the UPS' output load capacity. If the UPS' output load current is rising over than the low load operating current, the UPS' inverter starts working and the inverter output power feeds to the loads of UPS. If UPS' input power breaks out while UPS' inverter does not operate because the load current is low, the inverter starts working within 4(ms) with excessive output voltage which is ${\pm}$8(%) of normal UPS' output voltage. Like these. UPS can continuously feeds power to it's load device and reduce power consumptions.

• 전력전자학회논문지
• /
• 제20권5호
• /
• pp.448-455
• /
• 2015

A model predictive control (MPC) method without individual PWM has been recently researched to simplify and improve the control flexibility of a multilevel inverter. However, the input power of each H-bridge cell and the switching frequency of switching devices are unbalanced because of the use of a restricted switching state in the MPC method. This paper proposes a control method for balancing the switching patterns and cell power supplied from each isolated dc source of a cascaded H-bridge inverter. The supplied dc power from isolated dc sources of each H-bridge cells is balanced with the proposed cell balancing method. In addition, the switching frequency of each switching device of the CHB inverter becomes equal. A simulation and experimental results are presented with nine-level and five-level three-phase CHB inverter to validate the proposed balancing method.

• Journal of Power Electronics
• /
• 제15권1호
• /
• pp.54-64
• /
• 2015

This paper presents a current sensorless maximum power point tracking (MPPT) control method for dual-mode photovoltaic (PV) module-type interleaved flyback inverters (ILFIs). This system, called the MIC (Module Integrated Converter), has been recently studied in small PV power generation systems. Because the MIC is an inverter connected to one or two PV arrays, the power system is not affected by problems with other inverters. However, since the each PV array requires an inverter, there is a disadvantage that the initial installation cost is increased. To overcome this disadvantage, this paper uses a flyback inverter topology. A flyback inverter topology has an advantage in terms of cost because it uses fewer parts than the other transformer inverter topologies. The MPPT control method is essential in PV power generation systems. For the MPPT control method, expensive dc voltage and current sensors are used in the MIC system. In this paper, a MPPT control method without current sensor where the input current is calculated by a simple equation is proposed. This paper also deals with dual-mode control. Simulations and experiments are carried out to verify the performance and effectiveness of the proposed current sensorless MPPT control method on a 110 [W] prototype.

• Journal of Power Electronics
• /
• 제18권4호
• /
• pp.997-1006
• /
• 2018

This paper proposes a transformerless photovoltaic (PV) power converter system based on the DC/AC boost inverter, which can solve the leakage current and second-order ripple power issues in single-phase grid-connected PV inverters. In the proposed topology, the leakage current can be decreased remarkably since most of the common-mode currents flow through the output capacitor, by-passing parasitic capacitors, and grounding resistors. In addition, the inherent ripple power component in the single-phase grid inverter can be suppressed without adding any extra components. Therefore, bulky electrolytic capacitors can be replaced by small film capacitors. The effectiveness of the proposed topology has been verified by simulation and experimental results for a 1-kW PV PCS.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2014년도 추계학술대회 논문집
• /
• pp.85-86
• /
• 2014

The paper presents a power supply of atmospheric-pressure plasma reactor based on SiC (Silicon Carbide) MOSFET resonant inverter. Thanks to the capacitive characteristic of capacitive coupling plasma reactor type, the LC series resonant inverter had been applied to take advantages of this topology with the implementation of SiC MOSFET power modules as switching power devices. Designation of gate driver for SiC MOSFET had been introduced by this paper. The 5kVp, 5kW power supply had also been verified by experimental results.

• 전기학회논문지
• /
• 제67권12호
• /
• pp.1602-1610
• /
• 2018

Induction heating can convert electrical energy to thermal energy with high conversion efficiency and quick heating. Currently, a current source rectifier/inverter-fed parallel resonant circuit is widely used as an induction heating power supply for forging applications. However, the conventional induction heating power supplies composed of phase-controlled rectifier and SCR inverter have low efficiency and low power factor at input side, and require additional starting circuitry. So this paper proposes new induction heating power supply topologies for forging applications which have high power factor, high efficiency, and large output power. It also suggests detailed design guideline.

• 전력전자학회논문지
• /
• 제27권2호
• /
• pp.134-141
• /
• 2022

This study presents a method for reducing current distortion that occurs when a dual-buck inverter generates reactive power. Dual-buck inverters, which are only capable of unity power factor operation, can generate reactive power capabilities by modifying a modulation technique. However, under non-unity power factor conditions, current distortion occurs at zero-crossing points of grid voltage and output current. This distortion is caused by parasitic capacitors, dead-time, and discontinuous conduction mode operation. This study proposes a modified modulation method to alleviate the current distortion at zero-crossing point of the grid voltage. A repetitive controller is applied to reduce this distortion of the output current. A 1 kVA prototype is built and tested. Simulation and experimental results demonstrate the effectiveness of the proposed method.