• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.11 s.353
• /
• pp.77-82
• /
• 2006

Analog channel selection filter is described which is designed for a direct-conversion receiver of a IEEE 802.11a wireless LAN. The channel selection filter is an active-RC fifth-order Chebyshev filter with 10MHz cut-off frequency. Two-stage operational amplifier of the filter employs a current re-using feedforward frequency compensation scheme to minimize the power consumption. The filter has been implemented in a 0.18mm CMOS technology and the experimental results show 20mW power consumption with 1.8V supply voltage and 19dB out-of-band iIP3.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.7 no.2
• /
• pp.62-69
• /
• 2008

This paper proposes linearization technique that the linearity is improved by controlling IMD between the drive stage and the output stage. From the experimental results of W-CDMA 4FA input signal, this amplifier has ACLR of -48dBc@5MHz offset at 50W average power. Proposed linearization technique provides predistortion effect for using drive amplifier without additional circuit, which is the significant in this paper that it makes up for the weak point of analog predistortion method and feedforward method.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.796-802
• /
• 2013

In this study, we investigates active control technology to reduce the noise transmitted to the outside through the opening of enclosures. A numerical model based on acoustic boundary element method is first established. Using the numerical model, the acoustic transfer functions of the field points over the opening to the primary source at arbitrary locations are estimated. The feedforward control to minimize the acoustic power through the opening is then numerically implemented. The controller generates the secondary source to destructively interfere the noise transmission through the opening. Finally, a parametric study is conducted to evaluate the effects of the location and the number of the microphones on the control performance. Furthermore, the effects of the location of the secondary source on the performance of active noise control are investigated. It is followed that the control system implemented in this study leads to a significant reduction of about 35dB in sound power through the open using only on secondary source located at the optimized position.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.05a
• /
• pp.347-352
• /
• 2004

The author present a modified multi-loop algorithm including feedforward for controlling a 55kW step down chopper in the power supply of Maglev. The control law for the duty cycle consists of three terms. The first is the feedforward term which compensates for variations in the input voltage. The second term consists of the difference between the slowly moving inductor current and output current. The third term consists of proportional and integral terms involving the perturbation in the output voltage. This perturvation is derived by subtracting the desired output voltage from the actual output voltage. The proportional and integral action stabilizes the system and minimizes output voltage error. In order to verify the validity of the proposed multi-loop controller, simulation study was tried using Matlab simulink.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1262-1264
• /
• 2003

The author Present a modified multiloop algorithm including feedforward for controlling a 45kW step down chopper in the power supply of Maglev. The control law for the duty cycle consists of three terms. The first is the feedforward term which compensates for variations in the input voltage. The second term consists of the difference between the slowly moving inductor current and output current. The third term consists of proportional and integral terms involving the perturbation in the output voltage. This perturvation is derived by subtracting the desired output voltage from the actual output voltage. The proportional and integral action stabilizes the system and minimizes output voltage error. To verify the validity of the proposed multiloop controller, simulation study was tried using Matlab/sirnulink.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.24 no.3
• /
• pp.215-227
• /
• 2019

Grid-connected inverters should satisfy a certain level of total harmonic distortion (THD) to meet harmonics standards, such as IEEE 519 and P1547. The output quality of an inverter is typically degraded due to grid voltage harmonics, dead time effects, and the device's turn-on/turn-off delay, which all contribute to increasing the THD value of the output. The use of a harmonic controller is essential to meet the required THD value for inverter output under a distorted grid condition. In this study, an improved feedforward harmonic compensation method is proposed to effectively eliminate low-order harmonics in the inverter current to the grid. In the proposed method, harmonic components are directly compensated through feedforward terms generated by the proportional resonant controller with the grid current in a stationary frame. The proposed method is simple to implement but powerful in eliminating harmonics from the output. The effectiveness of the proposed method is verified through simulation using PSIM software and experiments with a 5 kW single-phase grid-connected inverter.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.312-317
• /
• 1996

This paper compares the output voltage control strategies of three-phase PWM inverter for uninterruptible power supply. The feedforward control, feedforward/feedback control, and decoupled feedback control in both the synchronous reference frame and the stationary reference frame are examined. In particular, it is shown that the response of the decoupled feedback controller in the synchronous reference frame can be improved by pole-zero cancellation method. It is also shown that the pole-zero cancellation method reduces to the deadbeat control, when it is implemented with digital controller.

• ETRI Journal
• /
• v.30 no.5
• /
• pp.729-734
• /
• 2008

Wireless communication systems, such as WLAN or Bluetooth receivers, employ preamble data to estimate the channel characteristics, introducing stringent settling-time constraints. This makes the use of traditional closed-loop feedback automatic gain control (AGC) circuits impractical for these applications. In this paper, a compact feedforward AGC circuit is proposed to obtain a fast-settling response. The AGC has been implemented in a 0.35 ${\mu}m$ standard CMOS technology. Supplied at 1.8 V, it operates with a power consumption of 1.6 mW at frequencies as high as 100 MHz, while its gain ranges from 0 dB to 21 dB in 3 dB steps through a digital word. The settling time of the circuit is below 0.25 ${\mu}s$.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.6
• /
• pp.109-118
• /
• 2002

The vibrational intensity and the dynamic response of a compound vibratory system had been controlled actively by means of a feedforward control method. A compound vibratory system consists of a flexible beam and two discrete systems - a vibrating source and a dynamic absorber. By considering the interactive motions between discrete systems and a flexible beam, the equations of motion for a compound vibratory system were derived using a method of variation of parameters. To define the optimal conditions of a controller the cost function, which denotes a time averaged power flow, was evaluated numerically. The possibility of reductions of both of vibrational intensity and dynamic response at a control point located at a distance from a source were fecund to depend on the positions of a source, a control point and a controller. Especially the presence of a dynamic absorber gives the more reduction on the dynamic response but the less on the vibrational intensity than those without a dynamic absorber.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.5C
• /
• pp.496-499
• /
• 2002

In this paper, a phase shifter with shifting photonic bandgap(PBG) cell in linear feedforward amplifier is designed and fabricated in 5GHz wireless LAN band. Now a day, the phase shifter has been fabricated with hybrid type. In this paper, a portion of PBG cell is shifted for the tuning phase. The phase shift was achieved maximum 80o in our PBG structure. Shifting PBG cell has been applied in feedforward main loop to cancel the main two tone signal.