• Transactions of Materials Processing
• /
• v.20 no.7
• /
• pp.485-490
• /
• 2011

The application of helical gears in crucial parts of automotive transmissions has been steadily increasing due to their higher power transfer performance compared to spur gears. However, the traditional gear manufacturing methods such as hobbing and deburring require large cycle times with expensive production lines so that there have been intensive efforts trying to manufacture gears via forging processes. Although forging processes for spur and bevel type gears have been developed on the practical level, the manufacturing of helical gears is still dependent on the traditional cutting process. Therefore, this paper seeks to develop a cold forward extrusion process for the helical gear with the pitch diameter of 43.5mm and a helix angle of $18.4^{\circ}$. A forward extrusion process was used due to the relatively small diameter of the target geometry. The material deforming behavior influenced by the die geometry was examined by using CAE analysis. Finally, it was found that the helical gear manufactured by the developed extrusion process satisfied the dimensional accuracy and mechanical characteristics for automotive transmissions.

• Proceedings of the CALSEC Conference
• /
• 2001.08a
• /
• pp.105-109
• /
• 2001

성형의 종류 ◈금속 성형 ㆍ 스탬핑(Stamping) ㆍ 정밀 블랭킹(Fine Blanking) ㆍ 딥 드로잉(Deep Drawing) ㆍ 다이캐스팅(Die Casting) ㆍ 인베스트먼트 주조(Investment Casting) ㆍ 분말 야금(Power Metallurgy) ㆍ 인발(Wire Drawing) ㆍ 압출(Extrusion) ㆍ 단조(Forging) ㆍ ㆍ코이닝(Coining) ㆍ... ◈비금속 성형 ㆍ 사출(Injection) ㆍ 압축(Compression) ㆍ 블로우 성형(Blow Molding) ㆍ 진공 성형(Vacuum Molding) ㆍ 발포 성형(Foam Molding) ㆍ 피복(Encapsulation) ㆍ 회전식(Rotational) ㆍ 주조(Casting) ㆍ 적층(Laminating) ㆍ 압출(Extrusion) ㆍ...(중략)

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1991.04a
• /
• pp.46-58
• /
• 1991

An upper-bound method is applied to determine the final-stage extrsuion load and the deformed configuration of extruded billet. A simple kinematically admissible velocity field for trhee-dimensional deformation at final-stage is proposed. From the proposed velocity field the upper-bound extrusion load, the velocity distribution and the configuration of extruded billet are determined byminimizing the otoal power consumption. Experiments are carried out with full-annealed commercial aluminum billets at room temperature by using different sizes of elliptic punches. The theroretical predictions both in extrusion load and deformed configuration of extruded billet are ingood agreements with the experimentalresults.

• Transactions of Materials Processing
• /
• v.3 no.1
• /
• pp.23-37
• /
• 1994

The upper bound element technique(UBET) is used to analyze the final stage of the axisymmetric forward extrusion. Kinematically admissible velocity field involving curved surface of velocity discontinuity is assumed. The required power to arise the piping defect is obtained and is compared with Aviture's solution a the same condition. Conditions for inception of the cavity and development of the pipe are predicted. The internal radius of the pipe and critical length of billet are also determined. Experiments are carried out for extrusion with lead specimens to investigate the piping phenomena. The theoretically predicted results showed reasonably good agreement with the experimental observation.

• Journal of Applied Tourism Food and Beverage Management and Research
• /
• v.13 no.1
• /
• pp.55-68
• /
• 2002

Flow properties of doenjang samples at various total solid contents (30, 32, 34, 36, 38, 40%) were evaluated in this study. Flow properties of doenjang samples was determined by using Haake concentric cylinderical viscometer and Instron testing machine with capillary extrusion viscometer, and consistency index(K), and flow behavior index(n) was also determined from power models, and yield stress was derived form Casson models and vanes methods. Doenjang samples showed shear-thinning (pseudoplastic) fluid with small magnitude of flow behavior index(n) (n=0.30-0.55). Casson yield stress was from 2.11 to 64.02(Pa). Vane yield stress was more effective than casson yield stress in property of reactivation. Apparent viscosity was decreased with the increase in temperature and activation energy was in the range of 6.58 to 10.70 kJ/mole. From the capillary extrusion method, K and n was increased with the increase in solid content with good correlation with. The result revealed that capillary extrusion method is useful for measuring the flow properties of doenjang.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.762-767
• /
• 2007

As a macromolecule material, melted rubber flow shows characteristics of shear thinning fluid. The dynamic viscosity of this rubber fluid is influenced by temperature and shear strain rate. In this study, the numerical simulation of rubber extrusion forming process has been performed using commercial CFD code, Polyflow. Power-law model considering the effect of shear rate is used for the computer simulation of this non-Newyonian flow. Also Non-isothermal behavior is considered as Arrhenius-law model. Distributions of velocity and temperature are predicted through the simulation.

• Elastomers and Composites
• /
• v.55 no.4
• /
• pp.329-338
• /
• 2020

In this study, three different die geometries were selected to understand the die characteristics in the film casting extrusion processes. First, large and small-scale T-dies were numerically simulated to observe the scaled-down effect on the flow inside the dies. Second, three different dies-keyhole, linear tapper coat-hanger die (LTCD), and curved tapper coat-hanger die (CTCD)-were numerically observed and discussed according to the mass flow rate. Finally, the die exit velocity profiles and die characteristics were observed and discussed based on the power-law index for the LTCD die. These numerical simulations and numerical data will aid the optimization of the die design in industrial fields.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.5
• /
• pp.223-230
• /
• 2007

Plasticity of clay bodies containing bottom ashes(BA) and small portion of other wastes was investigated. Plasticity indices of clay bodies using Atterberg limits were measured. It was confirmed that the plasticity indices could be applicable in actual forming process by extrusion. The forming possible compositions were found by changing the contents of water, bottom ash, stone dust, and sewage sludge. The relationship between the plasticity and physical properties of the aggregate green body was also investigated. The compositions for extrusion forming can be expected by measured the plasticity indices and these results were confirmed by real extrusion process. There is also strong relationship between the plasticity indices and the property of aggregate green body.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.2
• /
• pp.45-49
• /
• 2019

Herein we developed the hot extrusion technology to prepare n-type Bi-Te-Se-based thermoelectric materials with high reliability. Starting ingot was fabricated via melt-solidification process, then pulverized it into powders (${\sim}30{\mu}m$) by using high energy ball milling. By optimization of mold design and temperature-pressure conditions for hot extrusion, dense extrudate of 1.8 mm in diameter with high 00l orientation could be obtained from disc-shape compacted powders (20 mm in diameter). High power factor ${\sim}4.1mW/mK^2$ and enhanced mechanical strength ~50 MPa were simultaneously observed at 300 K.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1754-1757
• /
• 1997

Three-dimensional optimum design of coat-hanger die is performed using power-law and Carreau models. It is found that the three-dimensional optimum design algorithm shows good convergence with the non-Newtonian fludis. the nore realistic optimum design is accomplished by employing Carreau model with the three-dimensional design method. The effect of vixcosity modles is investigated by comparing the optimum manifold profiles and flow rate distributions of power-law and Carreau modles. Through the accurated viscosity representation of Carreau model, the effect of total flow rate on the optimum manifold profile is investigated.