• Title/Summary/Keyword: Power Seat

Search Result 121, Processing Time 0.029 seconds

Design of Compact Magneto-Rheological Fluid Damper for Artificial Low-Limb Prosthesis (Magneto-Rheological Fluid를 이용한 인공지능 의족의 Compact damper 개발)

  • Sung, So-Young;Kang, S.J.;Moon, I.H.;Moon, M.S.;Jang, S.M.
    • Proceedings of the KIEE Conference
    • /
    • 2005.07d
    • /
    • pp.2962-2964
    • /
    • 2005
  • Magneto-Rheological (MR) fluid is suspension of fine magnetic particles in a liquid carrier such as silicon oil or water. MR fluid exhibits solid-like mechanical behavior into chain or clusters with high yield stress when magnetic field is applied to the particles. The response of MR fluids is very quick and reversible after removal of the field. MR Fluids have high yield stress (up to 5kPs) and operate in low voltage power supply. Recently, MR damper using MR fluids was open used in vibration control system such as structural devices, seat vibration controllers and helicopter rotor systems, but it is too big in size and heavy. Therefore, it is not appreciate to rehabilitation devices such as prosthetic limbs.

  • PDF

Durability Performance Evaluation of Automotive Components Using Hydraulic 6 Axis Simulation Table (유압식 6자유도 가진 테이블을 이용한 자동차부품 내구성능 평가 기술)

  • Choi, G.J.
    • Journal of Drive and Control
    • /
    • v.5 no.1
    • /
    • pp.11-16
    • /
    • 2008
  • 자동차 부품은 주행 중 전후, 좌우, 상하방향의 병진 운동과 각 축에 대한 회전 운동 등 6자유도의 운동을 받는다. 이와 같은 운동에 따라 자동차에 탑재되는 운전석(cockpit), 의자(seat), 연료탱크, 라디에이터, FEM(front end module) 등의 부품 및 모듈 등은 6자유도 운동을 받으면서 각 부품의 기능을 수행하고 있다. 따라서 이들 부품을 짧은 시간 내에 개발하기 위해서는 가속내구시험평가가 필수적인데 이를 위해 유압식 6자유도 가진 테이블을 이용한 기술이 활용되고 있다. 본 해설에서는 자동차 부품 및 모듈의 내구성능 평가 과정과 함께 유압식 6자유도 가진 테이블을 보유하고 관련 부품의 진동내구성능을 평가하고 있는 군산대학교 자동차부품기술혁신센터(KATIC)의 시험 평가장비 및 사례를 기술하였다. 이와 같은 자동차 부품 내구성능평가 방법과 6자유도 가진 테이블을 이용한 시험은 향후 자동차부품 및 일반기계부품 개발업체에서 내구성능향상을 위하여 활용도가 더욱 증대될 것이다.

  • PDF

A study on the development of worm gear module for automobile (자동차용 웜기어 모듈 개발에 관한 연구)

  • Kim, Joo-Han;Sung, Ha-Kyeong;Rhyu, Se-Hyun
    • Proceedings of the KIEE Conference
    • /
    • 2005.10b
    • /
    • pp.219-221
    • /
    • 2005
  • Various adjustment devices which present automobile uses electric motion motor of reducer built-in type for user's convenience are increasing. The example are seat control motor, sunroof motor, power windows motor etc. To get low noise, high effectiveness special quality in automobile DC motor of reducer built-in type, reducer department's transmission efficiency and noise, vibration quality are very important. The reducer used to DC motor of automobile reducer built-in type use worm gear for enough torque and proper number of rotation. We need optimization design technology of deceleration module including worm gear and housing for reducer development that have special quality of good quality.

  • PDF

A Study on Prediction of Temperature Distribution in Pipe Girth Welding by Mapping Theory (사상 이론을 이용한 파이프 원주 용접의 온도 분포 예측에 관한 연구)

  • Jo, Yeong-Tae;Na, Seok-Ju
    • Transactions of the Korean Society of Mechanical Engineers A
    • /
    • v.24 no.12
    • /
    • pp.2935-2944
    • /
    • 2000
  • Gas tungsten arc(GTA) welding is used to rrpiar the seat ring in swing type check valve in power plant because of its high weld quality. In order to automate the welding process, it is needed to analyze the process of inside pipe girth welding. In this study, the shapes of weld bead on pipe inside and outside were predicted and its validity was investigated. On the assumption that the welding arc had a bivariate gaussian distribution, analytical solution was derived to predict the temperature distribution in pipe weld using mapping under consideration of physical relationships. The size of weld bean could be predicted from this equation and its accuracy was verified by experiments.

자동차용 소형모터의 소음ㆍ진동 개선을 위한 WORM 가공기술 개발

  • 이인환;강동배;안증환;김화영;조승환
    • Proceedings of the Korean Society of Precision Engineering Conference
    • /
    • 2004.05a
    • /
    • pp.222-222
    • /
    • 2004
  • 국내를 비롯한 전 세계적으로 자동차의 고급화가 진행됨에 따라 Power window, Seat adjusting, Pedal adjusting, Sunroof, Mirror adjusting, Electric shift motor등과 같이 각종 편의 및 안전장치 구동을 위하여 자동차용 기어드 모터 및 응용제품의 사용이 급증하고 있는 추세에 있고 그에 따른 모터 및 구성부품에 대한 요구수준도 점차 높아지고 있는 현실에 있다. 그러나, 자동차용 부품의 특징인 대량생산과 원가절감이라는 현실적인 제약에 의해 원하는 정도 달성 및 제품의 성능 향상과 경쟁력확보에도 큰 어려움을 겪고 있는 것이 업계의 현실이다.(중략)

  • PDF

Technological Progress Towards Commercialization of Organometal Halide Perovskite Solar Cells (유기금속 할라이드 페로브스카이트 태양전지의 상용화를 위한 기술의 진전)

  • Pyun, Sun Ho
    • Journal of the Korean Institute of Electrical and Electronic Material Engineers
    • /
    • v.27 no.12
    • /
    • pp.776-791
    • /
    • 2014
  • A marvellous solar cell technology system based on organometal halide perovskites has recently shown an unprecedented progress in power conversion efficiency (PCE); the certified one of 17.9% and unconfirmed of 19.3%, as well as the estimated electricity with a generating cost lower than the half of conventional methods based on fossil fuels. In this report the present status of stability with regards to moisture, ambient temperature, ultraviolet and lead toxicity as well as the key technological developments for the early commercialization are covered. Comprehensive understanding of material science for perovskites is required, together with complete encapsulation technologies beyond those for OLEDs, in order to ensure a 20-year-longer-than lifetime of PSCs (perovskite solar cells) and the stability according to the IEC 61646 damp heat test standard, which will result in the replacement of silicon solar cells with PSCs.

Design of Driver's Cab for KHST Power Car (한국형 고속전철 동력차 운전실 설계)

  • 염경안;강석택;박광복
    • Proceedings of the KSR Conference
    • /
    • 1999.11a
    • /
    • pp.139-145
    • /
    • 1999
  • The design of driver's cab includes the structure of cab frame, the layout of driver's cab equipment and facilities, i.e. driver's desk, seat, windows, floor, interior equipment, cab partition etc. The concept applied to the detail design has to be based on the ergonomics to guarantee the safety, comfort, and easy operation for the driver. In the aspect of manufacture, one more factor 'modulization' has to be considered into the design of sub blocks for cost-down. The design has to be implemented in the space allocated for driver's cab, which space is directly determined by the cab frame, optimized for the layout of driver's cab. The design process and results of the driver's cab for KHST will be described in this paper.

  • PDF

The Vehicle and Driver of China's Cultural Diplomacy: Global Vision Vs. Localised Practice

  • Liu, Xin
    • Journal of Contemporary Eastern Asia
    • /
    • v.17 no.1
    • /
    • pp.130-151
    • /
    • 2018
  • China's cultural diplomacy is mostly understood as an endeavour to build and project soft power, which draws on three sources of 'culture, political values and foreign policy' according to Nye. This paper focuses on the debates about the vehicle and agents of China's cultural diplomacy. It starts with a theoretical discussion of the competing views in the Chinese context, and develops an argument that the vehicle of China's cultural diplomacy tries to project soft power on two wheels of culture and political values, to serve the purpose of reshaping China's image away from being the 'cultural other' and 'ideological other' respectively. However, the state-led approach to driving this vehicle is generating some side effects with its sponsorship, censorship and presence in the driver's seat. Then the paper analyses the inherent tensions existing in practice both between the two sources of building soft power and between the two means of doing so, attraction and persuasion, with empirical evidence through a comparative case study of the Confucius Institutes in the US and South Korea. The finding shows that China's attempt at reshaping its image as an Eastern cultural contestant is often disrupted by its authoritarian political values, and the state-led persuasion is often reducing China's cultural attraction. Following this, the paper finishes with some recommendations regarding evolving the cultural diplomacy approach from a vertical one that is government-centred to a horizontal one that is network-based with multiple agents, and localising its practice by engaging the target audiences as stakeholders.

Development of Vibration Absorption Device for the Transportation-Trailer System(II) - Connecting Hitch for Power Tiller-Trailer - (수송 트레일러의 충격흡수장치 개발(II) - 동력경운기 연결 히치 -)

  • Hong J. H.;Lee H. J.;Lee S. B.;Park W. Y.;Kim S. Y.
    • Journal of Biosystems Engineering
    • /
    • v.30 no.3 s.110
    • /
    • pp.147-154
    • /
    • 2005
  • The improved hitch device, which connecting the trailer to power tiller, was developed. This device, composed with spring and rubber, could reduce the vibration and shock levels during driven on off-road. The vertical vibration accelerations for the improved hitch device were measured at 6 positions, i.e. engine, hitch, seat, and three points in trailer (front, middle, and rear) for not driving but at low engine speed of 500 rpm, and compared with the existing hitch device. The results of this study could be summarized as follows; The average vibration acceleration up to 120 Hz was $0.4m/s^2$ at engine part, but it was 0.08 and $0.05m/s^2$ at trailer for existing and improved hitch device, respectively. About $38\%$ of average acceleration level could be absorbed for the improved hitch device compared with existing hitch device. The average vibration acceleration up to 40 Hz was reduced to 0.12 and $0.06m/s^2$ at trailer for existing and improved hitch device respectively, showing the reduction effect of $50\%$. The maximum acceleration occurred at up to 20 Hz of low frequency was much higher than total acceleration occurred at up to 120 Hz, which means that much loss or damage could be occurred during transporting of agricultural products on off-road. The portions of average acceleration occurred at up to 20 Hz of low frequency were $27\%\;and\;21\%$ for the existing and improved hitch device, respectively.

Why A Multimedia Approach to English Education\ulcorner

  • Keem, Sung-uk
    • Proceedings of the KSPS conference
    • /
    • 1997.07a
    • /
    • pp.176-178
    • /
    • 1997
  • To make a long story short I made up my mind to experiment with a multimedia approach to my classroom presentations two years ago because my ways of giving instructions bored the pants off me as well as my students. My favorite ways used to be sometimes referred to as classical or traditional ones, heavily dependent on the three elements: teacher's mouth, books, and chalk. Some call it the 'MBC method'. To top it off, I tried audio-visuals such as tape recorders, cassette players, VTR, pictures, and you name it, that could help improve my teaching method. And yet I have been unhappy about the results by a trial and error approach. I was determined to look for a better way that would ensure my satisfaction in the first place. What really turned me on was a multimedia CD ROM title, ELLIS (English Language Learning Instructional Systems) developed by Dr. Frank Otto. This is an integrated system of learning English based on advanced computer technology. Inspired by the utility and potential of such a multimedia system for regular classroom or lab instructions, I designed a simple but practical multimedia language learning laboratory in 1994 for the first time in Korea(perhaps for the first time in the world). It was high time that the conventional type of language laboratory(audio-passive) at Hahnnam be replaced because of wear and tear. Prior to this development, in 1991, I put a first CALL(Computer Assisted Language Learning) laboratory equipped with 35 personal computers(286), where students were encouraged to practise English typing, word processing and study English grammar, English vocabulary, and English composition. The first multimedia language learning laboratory was composed of 1) a multimedia personal computer(486DX2 then, now 586), 2) VGA multipliers that enable simultaneous viewing of the screen at control of the instructor, 3) an amplifIer, 4) loud speakers, 5)student monitors, 6) student tables to seat three students(a monitor for two students is more realistic, though), 7) student chairs, 8) an instructor table, and 9) cables. It was augmented later with an Internet hookup. The beauty of this type of multimedia language learning laboratory is the economy of furnishing and maintaining it. There is no need of darkening the facilities, which is a must when an LCD/beam projector is preferred in the laboratory. It is headset free, which proved to make students exasperated when worn more than- twenty minutes. In the previous semester I taught three different subjects: Freshman English Lab, English Phonetics, and Listening Comprehension Intermediate. I used CD ROM titles like ELLIS, Master Pronunciation, English Tripple Play Plus, English Arcade, Living Books, Q-Steps, English Discoveries, Compton's Encyclopedia. On the other hand, I managed to put all teaching materials into PowerPoint, where letters, photo, graphic, animation, audio, and video files are orderly stored in terms of slides. It takes time for me to prepare my teaching materials via PowerPoint, but it is a wonderful tool for the sake of presentations. And it is worth trying as long as I can entertain my students in such a way. Once everything is put into the computer, I feel relaxed and a bit excited watching my students enjoy my presentations. It appears to be great fun for students because they have never experienced this type of instruction. This is how I freed myself from having to manipulate a cassette tape player, VTR, and write on the board. The student monitors in front of them seem to help them concentrate on what they see, combined with what they hear. All I have to do is to simply click a mouse to give presentations and explanations, when necessary. I use a remote mouse, which prevents me from sitting at the instructor table. Instead, I can walk around in the room and enjoy freer interactions with students. Using this instrument, I can also have my students participate in the presentation. In particular, I invite my students to manipulate the computer using the remote mouse from the student's seat not from the instructor's seat. Every student appears to be fascinated with my multimedia approach to English teaching because of its unique nature as a new teaching tool as we face the 21st century. They all agree that the multimedia way is an interesting and fascinating way of learning to satisfy their needs. Above all, it helps lighten their drudgery in the classroom. They feel other subjects taught by other teachers should be treated in the same fashion. A multimedia approach to education is impossible without the advent of hi-tech computers, of which multi functions are integrated into a unified system, i.e., a personal computer. If you have computer-phobia, make quick friends with it; the sooner, the better. It can be a wonderful assistant to you. It is the Internet that I pay close attention to in conjunction with the multimedia approach to English education. Via e-mail system, I encourage my students to write to me in English. I encourage them to enjoy chatting with people all over the world. I also encourage them to visit the sites where they offer study courses in English conversation, vocabulary, idiomatic expressions, reading, and writing. I help them search any subject they want to via World Wide Web. Some day in the near future it will be the hub of learning for everybody. It will eventually free students from books, teachers, libraries, classrooms, and boredom. I will keep exploring better ways to give satisfying instructions to my students who deserve my entertainment.

  • PDF