• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.611-612
• /
• 2005

Fuel cells is proved that potential energy is greater than the existing power generation. In this paper, we describe a principle of fuel cell which is used for next generation portable battery and brief characteristic of direct methanol fuel cells (DMFCs) that used for portable appliances by miniaturization of polymer electrolyte fuel cell. Lastly we describe about research investment for fuel cells.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.613-615
• /
• 2002

This paper deals with power factor of doubly fed induction generator for wind power generation in range of sub- and super-synchronous speed. To supply active and reactive power to grid. stator is connected to grid directly and rotor is connected to back-to-back PWM inverter for excitation. According to excitation level. DFIG could operate at the different mode. i.e., unity, leading, and lagging power factor.

• Journal of Power Electronics
• /
• v.10 no.3
• /
• pp.277-284
• /
• 2010

This paper presents a novel hybrid carrier based space vector modulation for cascaded multilevel inverters. The proposed technique inherits the properties of carrier based space vector modulation and the fundamental frequency modulation strategy. The main characteristic of this modulation are the reduction of power loss, and improved harmonic performance. The carrier based space vector modulation algorithm is implemented with a TMS320F2407 digital signal processor. A Xilinx Complex Programmable Logic Device is used to develop the hybrid PWM control algorithm and it is integrated with a digital signal processor for hybrid carrier based space vector PWM generation. The inverter offers less weighted total harmonic distortion and it operates with equal electrostatic and electromagnetic stress among the power devices. The feasibility of the proposed technique is verified by spectral analysis, simulation, and experimental results.

• Proceedings of the KIEE Conference
• /
• 2001.11c
• /
• pp.201-203
• /
• 2001

Safety is emphasized in nuclear power plant system for its characteristic. One of the most important systems to guarantee the safety of nuclear power plant is the PPS(Power protection system). The measurement control system includes PPS, which is similar to the human nervous system, is very important factor not only for the safety but also for the operation. Therefore, developing a technology to level up the performance of measurement system and reliability of the plant will bring cost-effective and safe generation of nuclear power. In this study, I researched composition of digitized PPS and algorithm for cyclic inspection.

• Journal of the Semiconductor & Display Technology
• /
• v.22 no.2
• /
• pp.64-71
• /
• 2023

If an impedance mismatch occurs between the source and load in a Radio Frequency transmission system, reflected power is generated. This results in incomplete power transmission and the generation of Reflected Power, which returns to the Radio Frequency generator. To minimize this Reflected Power, Impedance matching is performed. Fast and efficient Impedance matching, along with converging reflected power towards zero, is advantageous for achieving desired plasma characteristics in semiconductor processes. This paper explores Impedance matching by adjusting the Vacuum Variable Capacitor of an L-type Matching Module based on the trends observed in the voltage of the Phase Sensor and Electromotive Force voltage. After assessing the impedance matching characteristics, the findings are described.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.18 no.3
• /
• pp.135-142
• /
• 2015

Floating offshore structures should be designed by considering the most extreme environmental loadings which may be encountered in their design life. The most severe loading on a wave-offshore wind hybrid power generation system is wave loads. The principal parameters of wave loads are wave length, wave height and wave direction. The wave loads have different effects on the structural behavior characteristic depending on the combination of wave parameters. Therefore, the process of investigation for critical loads based on the individual wave loading parameter is need. Namely, the equivalent design wave should be derived by finding the wave condition which generates the maximum stress in entire wave conditions. Through a series of analysis, an equivalent regular wave height can be obtained which generates the same amount of the hydrodynamic loads as calculated in the response analysis. The aim of this study is the determination of equivalent design wave regarding to characteristic global hydrodynamic responses for wave-offshore wind hybrid power generation system. It will be utilized in the global structural response analysis subjected to selected design waves and this study also includes an application of global structural analysis.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.5
• /
• pp.543-548
• /
• 2006

This paper is to be researched into ozone generation character of Bi-Ti-Si type high dielectric ceramic catalyst discharge tube. And conditions of basic experiment are the outside diameter of discharge tube : 52 mm, the length of discharge tube : 350 mm, the frequence : 900 Hz, the temperature of cooling water : $25^{\circ}C$, quantity of flow : 5, 10, 20 L/min, pressure : 1.2, 1.4, 1.6 atm, and distance of discharge gap : 0.4, 0.6, 0.8 mm. Ozone generation characteristics were measured to consumption power. At quantity of flow : 20 L/min, discharge gap : 0.6 mm, pressure : 1.6, and consumption power : 150 W, Maximum ozone generation efficiency of 175 g/kWh was obtained. And a range of maximum ozone generation efficiency was measured below the flow quantity of 20 L/min at below pressure of 1.6 atm. However, Maximum ozone generation efficiency was measured over the flow quantity of 20 L/min at over pressure of 1.6 atm.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.1
• /
• pp.69-77
• /
• 2009

Recently, As increasing cleanroom size, Stocker system is trending the large size and long distance for LCD material transfer system. In order to rise a rate of production, the manufacturer are on the decrease of total tact time with Stocker system. And the manufacturer are requested to high speed of next generation Stocker system. Therefore, this paper propose Contactless Power Supply(CPS) system about high speed of next generation Stocker system. This paper proposes CPS system is applied in the long distance and straight section with Stocker system. The test results of input/output characteristic and efficiency of CPS system on operating pattern of Stocker system were analyzed, and proved the applicability on commercial use.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.17 no.4
• /
• pp.187-195
• /
• 2013

In this paper, firstly, acceleration-time histories were generated by varying strong motion duration in the frequency domain for application to a seismically isolated nuclear power structure, so as to examine the effects of strong motion duration on the behavior of the structure. Secondly, real recorded earthquakes were modified to match the target response spectrum based on the revised SRP 3.7.1(2007) and the modified time histories were applied to the analysis of a seismically isolated nuclear power structure. The obtained values of acceleration and displacement responses of the structure were, finally, compared with the values obtained in case of applying acceleration-time histories generated in the frequency domain to the structure.

• Proceedings of the KIPE Conference
• /
• 2008.10a
• /
• pp.206-208
• /
• 2008

In this paper, the two-stage DC-DC converter is proposed to make the control simple and to boost the low input voltage in the fuel cell generating system. The low efficiency of the conventional power converter is caused by a characteristic of the low-voltage and high-current in the fuel cell generating system. High-frequency transformer is needed to block the noise and to guarantee the safety of cell and load as a magnetically insulation. The proposed two-stage DC-DC converter for a fuel cell generation is more efficient than the traditional one-stage converter and easy to control. The design of a high-frequency transformer is also simple. Finally, the utility of the proposed converter is proved by the simulations and experiments.