• Journal of Energy Engineering
• /
• v.28 no.4
• /
• pp.35-41
• /
• 2019

In order to overcome these disadvantages, the halogen light source, which was previously used as a vehicle fog light, has increased power consumption and a short lifetime, and thus, an automobile light source is gradually being replaced with an LED. However, when the vehicle LED fog light is turned on, there is a disadvantage in reducing the life of the fog lamp due to the high heat generated from the LED. The heat generated by the LED inside the fog lamp is mainly emitted by the heatsink, but most of the remaining heat is released to the outside through convection. When cooling efficiency decreases due to convection, thermal energy generates heat to lenses, reflectors, and bezels, which are the main parts of lamps, or generates high temperatures in LED, thereby shortening the life of LED fog lights. In this study, we tried to improve the heat dissipation performance by convection in addition to the heat dissipation method by heat sink, and to determine the installation location of vents that can discharge the internal air or intake the external air of LED fog lamp for vehicle. Thermal fluid analysis was performed to ensure that the optimal data were reflected in the design. The average velocity of air increased in the order of Case3 and Case2 compared to Case1, which is the existing prototype, and the increase rate of Case3 was relatively higher than that of other cases. This is because the vents installed above and below the fog lamps induce the convective phenomena generated according to the temperature difference, and the heat is efficiently discharged with the increase of the air speed.

• Korean Journal of Optics and Photonics
• /
• v.25 no.1
• /
• pp.38-43
• /
• 2014

An external cavity laser supporting two wavelengths is demonstrated by incorporating polymer waveguide Bragg reflectors and a superluminescent light-emitting diode. An oversized rib waveguide structure and Bragg gratings are designed by using the effective-index and transmission-matrix methods. Bragg gratings with different periods are inscribed on a polymer waveguide through double-exposure laser interferometry. In order to tune the cavity loss affected by the reflectivity of Bragg gratings, a Bragg reflectors with varying length is incorporated. Two-wavelength-mode lasing is achieved for the device consisting of 2-mm long, 537-nm period gratings and 2.2-mm long, 540-nm period gratings; the lasing wavelengths are 1554 nm and 1564 nm, with an output power close to 0 dBm, a 20-dB bandwidth of 0.2 nm, and a side-mode suppression ratio of 45 dB.

• Korean Journal of Optics and Photonics
• /
• v.16 no.1
• /
• pp.13-20
• /
• 2005

Fiber-Bragg-grating external cavity laser(FGL) modules were fabricated and experimentally analyzed. Proposed as a cost-effective solution for optical sources in the WDM-PON access network, FGL modules were packaged to TO-CAN type. We obtained a low threshold current of 13 mA, and an optical output power of 3.6 mW with a bias current of 60 mA at $25^{\circ}C$. The lasing wavelength dependencies on current and temperature were as small as 5.2 pm/mA and 30 pm/$^{\circ}C$, respectively. These change rates of the wavelength with the temperature and current are smaller than those of the DFB laser. Single-mode oscillations with the side-mode suppression ratio(SMSR) over 30 dB are maintained above the threshold current level. The FGL modules can be directly modulated at 155 Mbps, PRBS(2$^{23}$ -1) NRZ signal. Through the BER plots, we did not see the significant degradations before and after the transmission over 20km of the SMF at 155 Mb/s.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.7
• /
• pp.710-721
• /
• 2013

The noise prediction of motor driving system is one of the most important parts in EV/HEV, as the number of power electronic devices increases. This paper describes the mechanism of noise making process and proposes a simulation model of motor driving system for the prediction of the conducted noise. Theoretical calculations and model based simulations were carried out. DOD-dependent-battery parameters were extracted by AC analysis, and an inverter model including dynamic diode was used. Furthermore, 2-D EM tool was used for the motor modeling and was combined with the circuit models of battery and inverter. The simulated voltages, currents and spectrums in the motor driving system showed qualitatively meaningful results, suggesting the validness of the suggested modeling methods.

• Archives of design research
• /
• v.17 no.3
• /
• pp.335-342
• /
• 2004

Recently there have been various research activities regarding Korean traditional aesthetics. However, those researches were mainly conducted individually, partially, and periodically, which resulted in unsystematic and incomprehensive works. Therefore, it is required to orginze all the precedent research works with more systematic and objective framework. Generally speaking, all the human activities including aesthetic activity have ends, procedure and means. In other words, human being needs three key elements for realizing any thought and those three elements include contents, formal, and practical element. Element of contents is ultimate goal to accomplish as value, concept, and meaning of thought with their aims. Formal element includes methods, principles, norms, procedure, formality and style comprising of thought in order to accomplish the goal. Finally, practical element refers to specific means, tool, media, material and techniques to concretize the contents through form. Almost all of thoughts and meaning which human being tries to express consist of language. Major elements in sentence include 'subject (omissible)' , 'objects (aim)', 'predicate (formality)', 'complement (means)' and they are composed systematically and hierarchically with rules in sentence. The study compared human activity model with language structure and analyzed their implication with design (aesthetics), which made it possible to propose analytic frameworks for traditional aesthetics. In addition, the study also systematically organized the way to realize traditional aesthetic value in the present context based on the methods developed in this study.

• Journal of Plant Biotechnology
• /
• v.48 no.2
• /
• pp.77-85
• /
• 2021

Hydroponic cultivation, in which crops are grown without soil and are unaffected by the weather, has many advantages over conventional soil cultivation. The crop's growth can be further accelerated by using nutrient solution in place of water. This study investigated the growth and physicochemical properties of hydroponic barley sprouts under various nutrient solution and artificial light treatments. The shoot, root, and total plant length increased over time, with the fastest growth occurring in the nutrient solution and light-emitting diode (LED) treatments. Fresh and dry plant weights were higher in the fluorescent lamp treatment than in the LED treatment. Barley sprout powder color differed slightly by treatment, with the Hunters L value ranging from 50.79 to 53.77; Hunters a value from -6.70 to -4.42; and Hunters b value from 13.35 to 14.76. The Hunters L and Hunters b values were highest in the LED treatment, whereas the Hunters a value was relatively highest in the fluorescent lamp treatment. The total phenol content was higher in the control than in the nutrient solution treatment; however, the total flavonoid content showed the opposite pattern to that of total phenol content, being highest in plants that were grown in nutrient solution. The Trolox equivalent antioxidant capacity (TEAC) was higher in the control group than in the nutrient solution group. The ferric ion reducing antioxidant power (FRAP) was higher in the fluorescent treatment group than in the LED treatment group. The total amino acid composition ranged from 106.82 to 122.63 mg/g dry powder, with the essential amino acid composition ranging from 47.01 to 56.19 mg/g, and non-essential amino acid composition from 67.86 to 77.66 mg/g. The most frequently detected compositional amino acid was aspartic acid, followed by glutamic acid, alanine, leucine, and valine.

• Korean Chemical Engineering Research
• /
• v.53 no.5
• /
• pp.620-626
• /
• 2015

$Ho^{3+}$ doped $SrAl_2O_4$ upconversion phosphor powders were synthesized by spray pyrolysis, and the crystallographic properties and luminescence characteristics were examined by varying activator concentrations and heattreatment temperatures. The effect of organic additives on the crystal structure and luminescent properties was also investigated. $SrAl_2O_4:Ho^{3+}$ powders showed intensive green emission due to the $^5F_4/^5S_2{\rightarrow}^5I_8$ transition of $Ho^{3+}$. The optimal $Ho^{3+}$ concentration in order to achieve the highest luminescence was 0.1%. Over this concentration, emission intensities were largely diminished via a concentration quenching due to dipole-dipole interaction between activator ions. According to the dependence of emission intensity on the pumping power of a laser diode, it was clear that the upconversion of $SrAl_2O_4:Ho^{3+}$ occurred via the ground state absorption-excited state absorption processes involving two near-IR photons. Synthesized powders were monoclinic as a major phase, having some hexagonal phase. The increase of heat-treatment temperatures from $1000^{\circ}C$ to $1350^{\circ}C$ led to crystallinity enhancement of monoclinic phase, reducing hexagonal phase. The hexagonal phase, however, did not disappear even at $1350^{\circ}C$. When both citric acid (CA) and ethylene glycol (EG) were added to the spray solution, the resulting powders had pure monoclinic phase without forming hexagonal phase, and led to largely enhancement of crystallinity. Also, N,N-Dimethylformamide (DMF) addition to the spray solution containing both CA and EG made it possible to effectively reduce the surface area of $SrAl_2O_4:Ho^{3+}$ powders. Consequently, the $SrAl_2O_4:Ho^{3+}$ powders prepared by using the spray solution containing CA/EG/DMF mixture as the organic additives showed about 168% improved luminescence compared to the phosphor prepared without organic additives. It was concluded that both the increased crystallinity of high-purity monoclinic phase and the decrease of surface area were attributed to the large enhancement of upconversion luminescence.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.6 s.336
• /
• pp.67-74
• /
• 2005

In this paper, high LO-RF isolation W-band MIMIC single-balanced mixer was designed and fabricated using a branch line coupler and a $\lambda$/4 transmission line. The simulation results of the designed 94 GHz balun show return loss of -27.9 dB, coupling of -4.26 dB, and thru of -3.77 dB at 94 GHz, respectively. The isolation and phase difference were 23.5 dB and $180.2^{\circ}$ at 94 GHz. The W-band MIMIC single-balanced mixer was designed using the 0.1 $\mu$m InGaAs/InAlAs/GaAs Metamorphic HEMT diode. The fabricated MHEMT was obtained the cut-off frequency(fT) of 189 GHz and the maximum oscillation frequency(fmax) of 334 GHz. The designed MIMIC single-balanced mixer was fabricated using 0.1 $\mu$m MHEMT MIMIC Process. From the measurement, the conversion loss of the single-balanced mixer was 23.1 dB at an LO power of 10 dBm. Pl dB(1 dB compression point) of input and output were 10 dBm and -13.9 dBm respectively. The LO-RF isolations of single-balanced mixer was obtained 45.5 dB at 94.19 GHz. We obtained in this study a higher LO-RF isolation compared to some other balanced mixers in millimeter-wave frequencies.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2004.04a
• /
• pp.5-9
• /
• 2004

In this paper, we studied the OCT(Optical Coherence Tomography) system which it has been extensively studied because of having some advantages such as high resolution cross-sectional images, low cost, and small size configuration. A basic principle of OCT system is Michelson interferometer. The characteristics of light source determine the resolution and the transmission depth. As a results, the light source have a commercial SLD with a central wavelength of 1,285 nm and FWHM(Full Width at Half Maximum) of 35.3 nm. The optical delay line part is necessary to equal of the optical path length with scattered light or reflected light from sample. In order to equal the optical path length, the stage which is attached to reference mirror is moved linearly by step motor And the interferometer is configured with the Michelson interferometer using single mod fiber, the scanner can be focused of the sample by using the reference arm. Also, the 2-dimensional cross-sectional images were measured with scanning the transverse direction of the sample by using step motor. After detecting the internal signal of lateral direction at a paint of sample, scanner is moved to obtain the cross-sectional image of 2-demensional by using step motor. Photodiode has been used which has high detection sensitivity, excellent noise characteristic, and dynamic range from 800 nm to 1,700 nm. It is detected mixed small signal between noise and interference signal with high frequency After filtering and amplifying this signal, only envelope curve of interference signal is detected. And then, cross-sectional image is shown through converting this signal into digitalized signal using A／D converter. The resolution of the OCT system is about 30$\mu\textrm{m}$ which corresponds to the theoretical resolution. Also, the cross-sectional image of ping-pong ball is measured. The OCT system is configured with Michelson interferometer which has a low contrast because of reducing the power of feedback interference light. Such a problem is overcomed by using the improved inteferometer. Also, in order to obtain the cross-sectional image within a short time, it is necessary to reduce the measurement time for improving the optical delay line.

• Journal of Bio-Environment Control
• /
• v.31 no.3
• /
• pp.180-187
• /
• 2022

In order to select suitable light in a plant factory, electric energy use efficiency and light use efficiency should be considered simultaneously to consider operating costs as well as quantitative and functional aspects. The growth characteristics, electric energy use efficiency, light use efficiency by light intensity, LED ratio, and photoperiod conditions were compared together. Light intensity is 60, 130, 230, and 320 µmol·m^-2·s^-1 treatments, and light quality is the mixing ratio of red light and blue light 8:2, 6:4, 4:6, and 2:8 treatments. Photoperiod is 9, 12, 15, and 18 hours treatments based on the daytime. In the light intensity experiment, the growth rate increased as the light intensity increased, but there was no significant difference in the light use efficiency. When comparing the leaf fresh weight per power consumption, only the 320 µmol·m^-2·s^-1 treatment group showed significantly low efficiency, and there was no significant difference in the other treatments, so 230 µmol·m^-2·s^-1, which produced the most, was the most efficient. In the light quality experiment, the ratio of red light and blue light was measured to be high at the same time as the growth rate and light use efficiency in RB 8:2, and there was no significant difference in color difference and flavonoids content, so a Red:Blue ratio of 8:2 was the most suitable condition. In the photoperiod experiment, the longer the photoperiod, the higher the growth rate. However, there was no significant difference in the growth rate over 12 hours of daytime, so 12 hours considering the light consumption efficiency was a suitable condition. Based on the above results, LED light environmental conditions for perilla growth in plant factories were light intensity, light quality, and day length of 230 µmol·m^-2·s^-1 or more, 8:2, and 12 hours or more, respectively.