• Journal of Communications and Networks
• /
• v.16 no.3
• /
• pp.280-292
• /
• 2014

This article presents a novel cooperative spectrum sharing (CSS) scheme. The primary transmitter transmits a complex Quadrature amplitude modulation (QAM) signal in the first phase, and CSS occurs in the second phase. The secondary transmitter with the largest forwarding channel gain among the nodes that successfully decode the primary signal in the first phase is selected for CSS. This selected node employs a pulse-amplitude modulation (PAM) signal for primary information message (IM) instead of the QAM signal, and it employs a modified PAM signal for the secondary IM. The proposed modified PAM signal depends on the amplitude of the primary PAM signal. This method results in no mutual interference and negligible primary interference constraint and allows a higher degree of exploitation of spatial diversity, thus enabling increase in secondary power to improve primary transmission. The outage performance is enhanced in both the primary and secondary systems. The critical region, in which the primary outage performance is enhanced with the proposed CSS scheme, can be adjusted and widened by varying either the modulation cooperation sharing factor or the number of secondary transmitters.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.12 no.3
• /
• pp.185-192
• /
• 2017

Due to the characteristics of low power, high durability and high density, NAND flash memory is being heavily used in various type of devices such as USB, SD card, smart phone and SSD. On the other hand, because of another characteristic of flash cell with the limited number of program/erase cycles, NAND flash memory has a short lifetime compared to other storage devices. To overcome the lifetime problem, many researches related to the wear leveling have been conducted. This paper presents a method called a TCB (Tracking Cold Blocks) using more reinforced constraint conditions when classifying cold blocks than previous works. TCB presented in this paper keeps a MCT (Migrated Cold block Table) to manage the enhanced classification process of cold blocks, with which unnecessary migrations of pages can be reduced much more. Through the experiments, we show that TCB reduces the overhead of wear leveling by about 30% and increases the lifetime up to about 60% compared to BET and BST.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.9
• /
• pp.801-806
• /
• 2015

In this paper, we propose cascade-form velocity controller for a permanent magnet synchronous motor (PMSM). The proposed controller consists of a sliding-mode controller (SMC) for the inner current control loop and a model-predictive controller (MPC) for the outer velocity control loop. With SMC, we can ensure that the current tracking error always converges to zero in finite time. The SMC is designed to track the desired currents. Additionally, with MPC, we can obtain the optimal velocity control input which minimizes the cost function. Constraint conditions for input and input variation are included in the MPC design. The simulation results are included to validate the performance of the proposed controller.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.6 s.237
• /
• pp.722-729
• /
• 2005

Design analysis of the solid oxide fuel cell and gas turbine combined power system is performed considering different methods for preheating cell inlet air. The purpose of air preheating is to keep the temperature difference between cell inlet and outlet within a practical design range thus to reduce thermal stress inside the cell. Three different methods considered are (1) adopting a burner in front of the cell, (2) adopting a preheater (heat transfer from the main combustor) in front of the cell and (3) using recirculation of the cathode exit gas. For each configuration, analyses are carried out for two values of allowable maximum cell temperature difference. Performance characteristics of all cases are compared and design limitations are discussed. Relaxation of the cell temperature difference (larger difference) is proved to ensure higher efficiency. Recirculation of the cathode exit gas exhibits better performance than other methods and this advantage becomes more prominent as the constraint of the cell temperature difference becomes more severe (smaller temperature difference).

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1537-1540
• /
• 2003

MEMS technology with micro scale is complete system utilized as the sensor. micro electro device. The metallization of MEMS is very important to transfer the power operating the sensor and signal induced from sensor part. But in the MEMS structures local stress concentration and deformation is often happened by geometrical shape and different constraint on the metallization. Therefore. this paper studies the effect of supporting type and thickness ratio about thin film thickness of the substrate thickness for the residual stress variation caused by thermal load in the multi-layer thin film. Specimens were made from materials such as Al, Au and Cu and uniform thermal load was applied, repeatedly. The residual stress was measured by FEA and nano-indentation using AFM. Generally, the specimen made of Al induced the large residual stress and the 1st layer made of Al reduced the residual stress about half percent than 2nd layer. Specimen made of Cu and Au being the lower thermal expansion coefficient induce the minimum residual stress. Similarly the lowest indentation length was measured in the Au_Cu specimen by nano-indentation.

• Journal of Digital Contents Society
• /
• v.13 no.3
• /
• pp.353-358
• /
• 2012

Wireless sensor networks consist of resource constraint devices which typically send data measured by sensors attached to the end devices towards a coordinator. The most often used medium access control protocol used in wireless sensor networks is the standard IEEE 802.15.4, where it is wireless standard introduced for low power, low cost wireless communication with moderate data rates. In this paper, we present implementation of both the IEEE 802.15.4 protocol stack and UART interface on the TI CC2530. We show that data via UART of our implemented IEEE 802.15.4 board are transmitted correctly in terms of captured frames.

• Journal of Korean Society of Steel Construction
• /
• v.18 no.6
• /
• pp.707-716
• /
• 2006

The optimization of the direct design system of semi-rigid steel frames using advanced analysis and genetic algorithm was presented. Advanced analysis can predict the combined nonlinear effects of connection, geometry, and material on the behavior and strength of semi-rigid frames. Geometric nonlinearity was determined using stability functions. On the other hand, material nonlinearity was determined using the Column Research Council (CRC) tangent modulus and parabolic function. The Kishi-Chen power model was used to describe the nonlinear behavior of semi-rigid connections. The genetic algorithm was used as the optimization technique. The objective function was assumed as the weight of the steel frame, with the constraint functions accounting for load-carrying capacities, deflections, inter-story drifts and ductility requirement. Member sizes determined by the proposed method were compared with those derived using the conventional method.

• Proceedings of the KIEE Conference
• /
• 2006.04a
• /
• pp.51-53
• /
• 2006

This paper proposes a portable ECG monitoring system, which integrates uptodate PDA and RF communication technology. The aim of the study is to acquire the subject's biomedical signal without any constraint. It has two types of transmission mode, which are total signal transmission mode and HR(heart rate)/SC(step count) transmission mode. In audition, wireless communication technology uses Zigbee Wireless PAN and can work in low-power mode, which is one of the advantages of ZiBbee communication technology. The developed system is composed of a transmitter and a receiver. The transmitter has three-axial acceleration sensor. ECG amplifier and Zigbee communication controller. In total signal transmission mode, it can send data 50 packets per second whose transmission speed corresponds to 300 ECG samples and 60 acceleration samples. In HR/SG transmission mode, it can calculate heart rate from EEG data with 216 samples per second and step count from acceleration data and send a packet every cardiac cycle. The receiver forwards the received data to PDA, where the data can be stored and displayed. Therefore, the developed device enables to continuous monitoring for Activities of Daily Living(ADL). Also, this method will reduce medical costs in the aged society.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.5
• /
• pp.380-388
• /
• 2002

This paper describes the optimum design for low-pressure steam turbine rotor of 1,000 MW nuclear power plant by using a combined genetic algorithm, which uses both a genetic algorithm and a local concentrate search algorithm (e.g. simplex method). This algorithm is not only faster than the standard genetic algorithm but also supplies a more accurate solution. In addition, this algorithm can find the global and local optimum solutions. The objective is to minimize the resonance response (Q factor) and total weight of the shaft, and to separate the critical speeds as far from the operating speed as possible. These factors play very important roles in designing a rotor-bearing system under the dynamic behavior constraint. In the present work, the shaft diameter, the bearing length, and clearance are used as the design variables. The results show that the proposed algorithm can improve the Q factor and reduce the weight of the shaft and the 1st critical speed.

• Journal of Internet Computing and Services
• /
• v.8 no.4
• /
• pp.81-91
• /
• 2007

Binding update for the routing optimization in MIPv6 can make the involved nodes vulnerable to various attacks. Therefore, secure binding update becomes an important research issue in MIPv6, and several protocols have been proposed for this purpose. In this paper, we compare several existing binding update protocols such as RR, SUCV and OMIPv6 and analyze the vulnerability of nodes to the possible attacks and drawbacks of address management and scalability and overhead of encryption operations. Then, we suggest the design requirements for the secure binding update and propose an advanced protocol based on the design principle. Through the analysis, we show that our protocol can achieve a higher level of security against the various attacks and enable better management of address, provide the location privacy and reduce the computational overhead of mobile nodes with constraint computational power.