• The Journal of Advanced Prosthodontics
• /
• 제7권3호
• /
• pp.214-223
• /
• 2015

PURPOSE. To measure the surface loss of dental restorative zirconia and the short-term bond strength between an indirect composite resin (ICR) and zirconia ceramic after various sandblasting processes. MATERIALS AND METHODS. Three hundred zirconia bars were randomly divided into 25 groups according to the type of sandblasting performed with pressures of 0.1, 0.2, 0.4 and 0.6 MPa, sandblasting times of 7, 14 and 21 seconds, and alumina powder sizes of 50 and $110{\mu}m$. The control group did not receive sandblasting. The volume loss and height loss on zirconia surface after sandblasting and the shear bond strength (SBS) between the sandblasted zirconia and ICR after 24-h immersion were measured for each group using multivariate analysis of variance (ANOVA) and Least Significance Difference (LSD) test (${\alpha}$=.05). After sandblasting, the failure modes of the ICR/zirconia surfaces were observed using scanning electron microscopy. RESULTS. The volume loss and height loss were increased with higher sandblasting pressure and longer sandblasting treatment, but they decreased with larger powder size. SBS was significantly increased by increasing the sandblasting time from 7 seconds to 14 seconds and from 14 seconds to 21 seconds, as well as increasing the size of alumina powder from $50{\mu}m$ to $110{\mu}m$. SBS was significantly increased from 0.1 MPa to 0.2 MPa according to the size of alumina powder. However, the SBSs were not significantly different with the sandblasting pressure of 0.2, 0.4 and 0.6 MPa. The possibilities of the combination of both adhesive failure and cohesive failure within the ICR were higher with the increases in bonding strength. CONCLUSION. Based on the findings of this study, sandblasting with alumina particles at 0.2 MPa, 21 seconds and the powder size of $110{\mu}m$ is recommended for dental applications to improve the bonding between zirconia core and ICR.

• Elastomers and Composites
• /
• 제44권3호
• /
• pp.282-289
• /
• 2009

건축현장에서 건물 방음 및 단열재의 씰링 용도로 일반 pressure-sensitive adhesive(PSA) tape이 주로 사용되고 있다. 일반 PSA tape은 먼지와 같은 이물질에 의해 점착력이 쉽게 감소하고 두께가 얇기 때문에 외부 자극에 의한 변형 및 파손이 쉽게 발생하여 방음재의 씰링 역할을 제대로 수행하지 못하는 결과가 발생하며, 이는 부실공사의 원인이 되기도 한다. 이러한 문제를 해결하기 위하여 본 연구에서는 FKM과 SBS를 이용하여 아스팔트를 개질하여 점착제로 적용하고자 하였다. 본 연구에서는 아스팔트의 점착력을 향상 시켜주기 위하여 선형과 방사형의 styrene-butadiene-styrene(SBS) 3, 6, 9 wt.%, 폐불소고무(FKM: fluoroelastomers) 10, 20, 30 wt.%를 아스팔트에 첨가하여 개질 아스팔트를 제조하였고 이들의 연화점, 점도, 인장강도 및 점착력 등의 물리적 특성을 평가하였다. SBS 개질 아스팔트는 SBS가 첨가됨에 따라 연화점 및 점도가 상승하는 거동을 나타냈으며 순수 아스팔트 보다 높은 점착력을 나타내었다. FKM 개질 아스팔트의 경우는 FKM이 첨가 되어도 연화점 및 점도 변화가 없었으며 FKM과 아스팔트의 낮은 계면 결합력으로 점착력이 증가하지 않았다. 온도가 증가할수록 개질 아스팔트의 점도는 감소하였지만 SBS 개질 아스팔트의 경우에는 온도상승에 따른 점도 감소가 적어 상당히 넓은 온도 범위에서 점착력을 유지하였으며 선형 SBS가 6 wt.% 첨가된 것이 최적의 점착 특성을 나타내었다.

• 대한치과교정학회지
• /
• 제26권3호
• /
• pp.317-324
• /
• 1996

브라켓 접착제로서 현재까지 널리 사용되어 온 복합레진의 단점들을 보완하기 위해 최근 교정영역에서도 글라스 아이오노머 시멘트의 사용에 관심이 집중되고 있다. 이에 본 연구는 글라스 아이오노머 시멘트를 교정용 브라켓 접착제로 사용시 그 접착강도를 측정해 봄으로써 글라스 아이오노머 시멘트의 임상적 효용성을 알아보기 위하여 시행하였다. 교정치료를 위해 발거한 소구치에 자가중합형 글라스 아이오노머 시멘트인 Shofu Glaslonomer Cement(Shofu Co., U.S.A.)와 GC Fuji I(GC Co., Japan), KETAO CEM(ESPE Co., West Germany)을 분말-액 비율을 달리하여 소구치용 표준형 에지와이즈 브라켓을 접착한 후 15분간 실온에 방치 하였다가 증류수에 침 적 하여 $37^{\circ}C$ 항온조에 보관하였다. 보관한 후 24시간 및 3개월 후에 만능시험기로 인장접착강도를 측정하고 브라켓의 탈락 양상을 관찰하여 다음과 같은 결과를 얻었다. 1. 분말-액 비율을 1로하고 24시간 침적한 경우를 제외하고는 KETAC-CEM이 가장 높은 인장접착강도를 나타내어 (p<0.05) 브라켓 접착시 임상적 유용성이 있으리라 생각되며, Shofu Glaslonomer Cement와 GC Fuji I은 접착강도가 매우 낮았다. 2. 분말-액 비율을 증가시킬때 인장접착강도는 대체로 증가되는 경향을 보였다. 3. 침적시간이 경과할수록 인장접착강도는 대체로 증가되는 경향을 보였다. 4. 브라켓의 탈락 양상은 법랑질과 접착제의 경계부에서 탈락하여 치질에 잔존하는 접착제가 거의 없는 경우가 가장 높은 비율(54.2%)을 차지하였고, 그 다음은 브라켓과 법랑질에 부분적으로 붙어서 탈락한 경우 (36.7%)였으며, 접착제와 브라켓 경계부에서 탈락한 것(9.1%)이 가장 적었다.

• 한국조리학회지
• /
• 제23권2호
• /
• pp.95-103
• /
• 2017

The present study was performed to develop healthier sweeteners for brown rice Dasik with chia seed powder. The quality features and sensory evaluation were tested for brown rice Dasik with chia seed powder added with five different sweeteners and the results are as follows. The Dasik (DS) with isomalto-oligosaccharide and starch syrup received the highest scores on moisture content tests. The results from hardness tests identified the DS with agave syrup as the hardest, and the results from the adhesiveness test verified that the DS with agave syrup as well as the DS with starch syrup produce the most adhesive DS. The results of the springiness test show that the DS with starch syrup has higher springiness than other sweetners. The highest score for the chewiness and cohesiveness tests was the DS with starch syrup, while the DS with isomalto-oligosaccharide received the highest score on the gumminess test. The results of the chromaticity measurement test found that the DS with starch syrup showed the highest score of 'L' and the lowest score with fructo-oligosaccharide. In addition, the highest score of 'a' was DS with isomalto-oligosaccharide and the lowest score of 'b' was the DS with starch syrup. The results of sugar content displayed that the DS with starch syrup was the highest and the DS with fructo-oligosaccharide was the lowest score. The results of sensory evaluation verified that color did not influence evaluators' preference investigation. The results of sweet flavor test found that the DS with honey and the DS with agave syrup had the most preferred by participants, but there was no statistically significant difference among all five different sweeteners from the sweet taste test. Furthermore, the DS with agave syrup received the highest score while the DS with agave syrup scored the lowest from the hardness preference test. General preference evaluation identified the highest score with the addition of fructo-oligosaccharide and the lowest score with the addition of isomalto-oligosaccharide. Thus, the findings of the present study provide the meaningful results to demonstrate the DS with fructo-oligosaccharide is the most suitable sweetener to manufacture brown rice DS added by chia seed powder, and this result will help marketers with creating meaningful strategies and with developing similar products using chia seed powder.

• 한국전기전자재료학회논문지
• /
• 제17권5호
• /
• pp.486-491
• /
• 2004

Dimensionally stable anode(DSA) can be used for the hydro-metallurgy of non-ferrous metals like as Zn, and the electrolysis of sea water. MnO$_2$ electrode satisfies the requirements of DSA, and has a good cycle life and a low overpotential for oxygen evolution. MnO$_2$ electrodes based on Ti matrix were prepared by using thermal decomposition method and also MnO$_2$ was coated on Ti and Pb matrix with DMF and PVDF compositions. The MnO$_2$ electrodes prepared by thermal decomposition method had very weak adhesive strength onto Ti matrix and MnO$_2$ layer was removed out so that electrochemical properties for MnO$_2$ were not investigated. The viscosity of solvent used as a binder of MnO$_2$ Powder increased with the increasing PVDF contents. The thickness of the MnO$_2$ layer on Pb matrix in DSA, which was prepared with 5 times dipping at the solution mixed with PVDF : DMF = 1 : 9, was 150${\mu}{\textrm}{m}$. When the ratio of PVDF to MnO$_2$ was lower than 1 : 6, the Pb electrode didn't show any reaction irrespective of the concentrations of DMF. However, When the ratio of PVDF to MnO$_2$ was higher than 1: 6, the Pb electrode showed constant current reactions and homogeneous cyclic voltammetry even though at a high cycle. The reason for the high current and homogeneous cyclic voltammetry is the good catalytic reactions of MnO$_2$ powder in electrode.

• 한국분말재료학회지
• /
• 제18권3호
• /
• pp.226-237
• /
• 2011

W-ZrC and W-HfC composite powders were fabricated by the Plasma Alloying & Spheroidization (PAS) method and the powders were sprayed into hybrid coating layers by using Low Vacuum Plasma Spray (LVPS) process, respectively. Microstructure, mechanical properties, and ablation characteristics of the fabricated coating layers were investigated. The LVPS process led to successful production of W-Carbide hybrid coatings, approximately 400 ${\mu}M$ or above in thickness. As the substrate preheating temperature increased from $870^{\circ}C$ to $917^{\circ}C$, the hardness of the W-ZrC coating layer increased due to decreased porosity. Vickers hardness showed higher value (about 108.4 HV) in W-ZrC hybrid coating material compared to that of W-HfC while adhesive strength was found to be similar in both coating layers. The plasma torch test revealed good ablation resistance of the W-Carbide hybrid coating layers. The relatively high performance W-ZrC coating layer at the elevated temperature is thought to be attributed to both the strengthening effect of ZrC particle remained in the layer and the formation of ZrO2 phase with high temperature stability.

• Applied Microscopy
• /
• 제29권1호
• /
• pp.67-73
• /
• 1999

분말시료를 epoxy로 포매 (embedding)한 후 ion milling하는 방법으로 TEM 시편을 준비하는 경우에는 시료와 epoxy와의 milling정도의 차이 때문에 좋은 시편을 만들기 어렵다. 이러한 문제점을 극복하기 위해서 포매 물질에 대한 분말시료의 상대 밀도를 높여 주는 방법을 시도하였다. 일반적인 진공법보다는 원심분리기법을 이용하여 포매하는 것이 시료의 밀도를 높일 수 있었다. 또한, 비슷한 크기의 분말의 혼합보다는 서로 다른 크기의 분말을 혼합한 후 원심분리기를 이용하여 포매할 때, 큰 입자들 사이로 작은 입자들이 유입되면서 분말의 밀도가 더욱 높아지는 것을 알 수 있었다. 이렇게 준비된 시료는 ion milling정도의 차이에서 오는 문제점을 크게 줄일 수가 있어 TEM 관찰에 필요한 시편을 얻을 수 있었다. 원심분리기법은 마이크로미터 이하 크기의 구형, 판상 및 침상의 분말시료에서부터 TEM 시편을 준비하는 데에도 매우 효과적임이 드러났다.

• 한국세라믹학회지
• /
• 제48권6호
• /
• pp.516-519
• /
• 2011

Indium tin oxide (ITO) coatings were made using an ITO slurry and an ITO sol. This was achieved by dispersing nanosized ITO powder in a mixed solvent without any dispersant and developing an adhesive ITO sol from indium acetate and tin tetrachloride in a mixture of DMF and n-butanol. Coating was carried out in one step by spin coating an ITO slurry, which was then followed by an ITO sol over it. Here, the sol penetrates into the nano ITO particle layers to make them adhere to each other as well as to a glass substrate. This is then followed by sintering at 500$^{\circ}C$ for 1 h to produce a uniform film consisting of ITO particles of about 50 nm and 10 nm. ITO films were obtained with sheet resistances from 450 to 1500 ohm/${\Box}$ by varying spin speed and concentration. Transmittance is higher than 90% at 550 nm.

• 대한의용생체공학회:의공학회지
• /
• 제16권4호
• /
• pp.533-542
• /
• 1995

The present study investigated the effectiveness of pretreatment on dentin bonding. The adhesive resin was 5% 4-methacryloyloxyethyl trimellitate anhydride (4-META) in methyl methacrylate (MMA) combined with poly-MMA powder. Polymerization of this resin was initiated by tri-n-butyl borage (TBB). Ground bovine dentin samples were etched with either an aqueous solution of 10% citric (10-0 solution) (Group I) or aqueous solution of 10% citric acid and 3% ferric chloride(10-3 solution) (Group ll ). After etching, the primer (an aqueous solution of 35% hydroxyethyl methacrylate (HEM- A) and 5% glutaraldehyde was applied on the differently etched surfaces (Group III , Group IV). The 10-0 treatment showed the lowest tensile bond strength, followed by the 10-3 treatment, primer application after the 10-0 treatment and primer application after the 10-3 treatment. The relationship among the surface morphology after pretreatment, fractured surface morphology and tensile bond strength was examined. It revealed that the surface morphology change by different pretreatment influenced the bond strength and the resulting fractured surface morphology. The correlation of tensile bond strength with the fracture morphology was explained.

• 한국가구학회지
• /
• 제14권2호
• /
• pp.1-12
• /
• 2003

This study was carried out to determine the mechanical and physical properties of particle boards glued with condensed tannin (Wattle Tannin) powder that was single-molecule phenolic compounds like powdered phenolic resin. Our findings are; 1) It is necessary to spray water on the chip surfaces for effective application of powdered -form tannin resin. It shows that the best and optimum mat moisture increase is 14% of water spray on the surface of chips for developing PB properties. 2) In general, for both liquid and powdered tannin adhesives, their physical and mechanical properties has been proportional to the increase of resin level. But, the most efficient addition ratio is 16% of resin on dry basis. Specially, it is found that the resin level influences on the amount of free formaldehyde emission. The higher the resin level is, the lower the emission is. These phenomena seem to result from the increase of hexamine or formaline in the adhesives used as a hardener, that reduce the free-formaldehyde amount by reaction of tannin of poly-molecule and water. 3) The optimum condition for manufacturing PBs is the condition of hexamine of 5% and formaline of 6% in mechanical and physical properties. Hexamine is superior to formaline in mechanical and physical properties along with the control of the free formaldehyde emission amount. The result of NaOH's addition is insignificant in all experiments of both mechanical and physical properties.