• 대한치과보철학회지
• /
• 제60권2호
• /
• pp.152-159
• /
• 2022

상악 총의치의 유지에 있어 후방 구개 폐쇄(Posterior palatal seal)의 역할은 중요하다. 최종 인상을 채득한 후 주모형상에 구를 형성하는 기계적 방법을 통하여 상악 의치에 추가적인 유지를 부여할 수 있으나 이는 임상적인 과정에서 간과되곤 한다. 그 결과 기공사에 의해 환자의 개별적 특성을 고려하지 않고 일률적인 방법으로 후방 구개 폐쇄가 형성된다. 현재까지 많은 이들에 의해 다양한 후방 구개 폐쇄 형태가 소개되어 왔다. 본 증례 보고는 환자의 해부학적 구개 형태 및 기능시 조직 변위를 고려한 후, 적절한 후방 구개 폐쇄의 위치 및 형태를 결정하여 상악 총의치를 제작하는 과정을 보고하는 바이다.

• 대한치과보철학회지
• /
• 제22권1호
• /
• pp.23-32
• /
• 1984

The effects between preexisting four types and one that author had designed of posterior palatal seal on the retention of denture base were compared and observed from six systemically healthy edentulous subjects. Using one without posterior palatal seal as the control, the retention of each type was measured and analyzed six times with cantilever type Load cell after adaptation of denture base, which were constructed with usual manner. The following results wear obtained. 1. Morphological and positional changes of posterior palatal seal effected on denture retention. 2. No specific type showed most desirable effect in every experimental subject. 3. Experimental subject I, II, VI showed higher retention on the control in every type. 4. In five types of posterior palatal seal, for subject III, VI F types and for subject II, V C types were most effective. 5. In each experimental subject F type showed higher retention than the control.

• 대한치과기공학회지
• /
• 제6권1호
• /
• pp.5-10
• /
• 1984

This experimental study was performed to investigate the effect of the wax extension method of posterior palatal seal area, introduced by Vig, on the amount of the vertical occlusal change of processed dentures. Twenty samples of maxillary wax trial dentures were constructed. Among them, the posterior palatall seal of ten samples were extended with wax over the posterior wall of the cast while that of the other ten were not. Then all were processed with self-curing resin and the amount of the vertical occlusal change was compared. The obtained result was that this method was proved to be effective in reducing the amount of the vertical occlusal change occuring in denure proccsing.

• 대한치과의사협회지
• /
• 제22권7호통권182호
• /
• pp.554-554
• /
• 1984

• 대한치과의사협회지
• /
• 제23권4호통권191호
• /
• pp.291-297
• /
• 1985

• 대한치과보철학회지
• /
• 제33권2호
• /
• pp.358-394
• /
• 1995

The author studied the actual conditions on the production of dental prosthesis made in laboratories, and also studied interrelationships between dentists and laboratory technicians in both personal and technical aspects. Two hundred-eighty four technicians, work in dental laboratories presently, were surveyed via mail and direct contact during the period from June 1 to June 30 and August 27 to August 28 in 1994 respectively. The obtained results were as follows : 1. Among the respondents, 90.5% we re working in commercial dental laboratories and their laboratories were mainly located in the Seoul area(40.9%, P<0.05). The numbers of employees in these laboratories were less than 10 persons(70.0%, P<0.01), and 75.9% of these laboratories have been in operation less than 15 years. 2. Most laboratory procedures were accomplished according to established disciplines. However, procedures such as die trimming in fixed restorations and the qualifications of the people designing removable partial dentures were not. Other problem areas were boxing of the working cast, the person determining the posterior palatal seal area, selection and arrangement of artificial teeth, occlusion rim correction and laboratory remounting of the processed denture in complete denture restorations. 3. Only half of the requesting dentists could send work authorizations to the laboratories with their work and even so, its contents were quite lacking. Consequently, there must be some standards in writing work authorization. 4. Technicians most desired clean and accurate impressions in fixed and removable dentures, and enough tooth reduction in porcelain fused to metal restorations. 5. For the establishment of better relationships between dentist and dental technician, the respondents desired the establishment of equal footing first(33.5%), and frequent conversations and muture understanding second(25.9%).

• 대한치과보철학회지
• /
• 제44권6호
• /
• pp.712-721
• /
• 2006

Statement of problem. Acrylic resin is most commonly used for denture bases. However, acrylic resin has week points of volumetric shrinkage during polymerization that reduces denture fit. The expandability of POSS (Polyhedral Oligomeric Silsesquioxane) containing polymer could be expected to reduce the polymerization shrinkage of denture bases and would increase the adaptability of the denture to the tissue. Purpose. The purpose of this study was to compare the dimensional stability in the conventional acrylic resin base, POSS-containing acrylic resin base, and metal bases. Materials and methods. Thirty six maxillary edentulous casts and dentures of different base were fabricated. Tooth movement and tissue contour change of denture after processing (resin curing, deflasking, decasting and finishing without polishing) and immersion in artificial saliva at $37^{\circ}C$ for 1 week and 4 weeks were measured using digital measuring microscope and threedimensional laser scanner. Results. The results were as follows: 1. The conventional resin group showed significant (p<0.01) dimensional change throughout the procedure (processing and immersion in artificial saliva). 2. After processing, the metal group and POSS resin group showed lower linear and 3-dimensional change than conventional resin group (p<0.01). 3. There was no statistically significant linear and 3-dimensional change after immersion for 1 week and 4 weeks in metal and POSS resin group. 4. In all groups, the midline and alveolar ridge crest area presented smaller 3-dimensional change compared with vestibule and posterior palatal seal area after processing and soaking in artificial saliva for 1 week and 4 weeks (p<0.01). Conclusion. In this study, a reinforced acrylic-based resin with POSS showed good dimensional stability.

• 대한치과보철학회지
• /
• 제61권4호
• /
• pp.344-355
• /
• 2023

총의치 제작 과정 중 정확한 최종인상을 얻기 위해서는 정확한 예비인상 채득이 선행되어야 한다. 본 증례에서는 비정형적인 악궁 형태를 가진 환자에서 기성 트레이 및 구강 스캐너로 채득하여 제작한 예비모형과 개인트레이를 비교하였다. 58세 남자 환자로 상, 하악 총의치 제작을 위해 본원 구강악안면외과에서 의뢰되었다. 상하악궁 모두 좁고 긴 형태로 비정형적인 형태를 보였다. 기성 트레이를 이용하여 채득한 예비모형은 구강 스캐너를 이용한 예비 모형에 비해 상악의 경우, 협측의 변연이 과연장되었고, 후방 구개 폐쇄 부위에서는 압박되어 있었다. 또한 하악에서도 과연장되었으나, 상악에 비하여 그 양이 많지 않았다. 그리고 구강 스캐너에 의해 채득된 예비모형은 기성 트레이로 채득된 예비 모형에 비해 저연장되었으나, 해부학적 지표는 충분히 인기되었다. 기성 트레이에 의해 제작된 개인 트레이는 IOS에 의해 제작된 개인 트레이에 비하여 구강 내 시적 시, 개인 트레이의 조정량이 많았고 진료 시간이 증가하였다. 본 증례를 통해 비정형적인 악궁을 가진 환자에게 3D 구강 스캐너로 인상을 채득하는 것이 대안이 될 수 있음을 보고하는 바이다.