• 한국공간구조학회논문집
• /
• 제15권1호
• /
• pp.57-64
• /
• 2015

This paper shows the test results of continuous reinforced concrete beams with external post-tensioning rods. Six three-span beams were prepared and tested to fail. Three beams were designed to have flexure-dominating behavior and the others to have shear-critical behavior. In each group, one beam without external post-tensioning rods was designated as a control beam and two beams had the external post-tensioning rods of 18 mm or 22 mm diameter. External post-tensioning rods were installed within an interior span of 6000 mm. They show V-shaped configuration because two anchorages were located at the top of interior supports and a saddle pin at mid-span was installed at the bottom of the beam. Test results show that the load and shear capacities of strengthened beams were increased when compared with the control beam. Additionally, the measured shear strength was compared with the strength predicted by ACI 318-11 code equations. The detailed ACI 318-11 equation predicted the measured shear strength and failure location of the continuous beam reasonably well.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 추계학술대회 논문집
• /
• pp.1034-1039
• /
• 2004

The major objective of this study is to investigate the effects and application of reinforcement for steel plate girder railway bridge by the external prestressing method. It analyzed the mechanical behaviors of non-ballasted railway bridge with ballast reinforced and external post-tensioning reinforced on the finite clement analysis for the static and dynamic behavior. As a result, the reinforcement of ballasted railway bridge the external prestressing method are obviously effective for the additional dead force which is ballast. The analytical study are carried out to investigate the post-tension force decrease bending behavior and deflection in composite bridge for serviceability. To develop two type FEM model which reflect well the post-tension force transverse distribution behavior of servicing bridge. With the comparing the results of railway bridge with ballast which carried out before the post-tensioning with the results of railway bridge with ballast which carried out after post-tensioning, It is investigated that the additional dead load decrease effect and bending behavior of servicing bridge is effect by the post-tensioning. The reinforcement by using the external tendon can be reducing that structure of a degradation phenomenon by unusual stresses due to additional dead load and other problems.

• 한국강구조학회 논문집
• /
• 제12권5호통권48호
• /
• pp.549-558
• /
• 2000

외부 후 긴장 공법은 설계에 수반되는 구조해석이 비교적 명확하여 강교량 구조물뿐만 아니라 건축구조물 등 그 적용 범위가 매우 넓은 보강방법이다. 본 연구에서는 후 긴장 공법에 있어서 긴장력 도입 과정의 강합성보의 거동을 연구하기 위하여 긴장력 증가에 따른 긴장재, 경간 중앙부 하부 플랜지, 정착단 주형 하부 플랜지의 도입 변형율과 긴장재 절곡 각도에 따른 도입 전단력 및 압축력을 실험 및 해석적으로 분석하였다. 또한 긴장력 도입 후 정적 휨 재하 실험을 수행하여 긴장력 도입 정도에 따른 휨 보강 정도를 분석하였으며, 절곡 각도의 변화에 따른 전단보강 및 휨 보강 양상을 연구하였다. 그 결과 외부 후 긴장력 도입에 따른 휨 보강 효과가 매우 높은 것으로 분석되었으며, 긴장재의 절곡 배치에 의해서는 추가적으로 전단보강 효과까지 나타났다.

• 한국공간구조학회지
• /
• 제10권3호
• /
• pp.18-21
• /
• 2010

• 한국철도학회논문집
• /
• 제9권2호
• /
• pp.151-159
• /
• 2006

It analyzed the mechanical behaviors of non-ballasted railway bridge (steel plate girder type) with ballast reinforced on the finite element analysis, field test and laboratory test far the static and dynamic responses. The major objective of this study is to investigate the effects and application of reinforcement for steel plate girder railway bridge by the external post-tensioning method. The reinforcement of non-ballast railway bridge had obviously stable dynamic behaviors due to the additional dead force which was ballast. But in case of static behaviors, static displacements and stresses had increased nearly the allowable values. Therefore we analyzed the mechanical behaviors of non-ballasted railway bridge with ballast reinforced and external post-tensioning reinforced on the finite element analysis and laboratory test for the static and dynamic behavior. As a result, the reinforcement of ballasted railway bridge the external post-tensioning method are obviously effective for the additional dead force which is ballast. The analytical and experimental study are carried out to investigate the post-tension force decrease bending behavior and deflection in composite bridge for serviceability. The servicing railway bridge with ballast reinforced has need of the reasonable reinforcement measures which could be reducing the effect of additional dead load that degradation phenomenon of structure by an unusual. stresses and a drop durability.

• 한국도로학회논문집
• /
• 제10권4호
• /
• pp.257-267
• /
• 2008

본 연구에서는 프리스트레스트 콘크리트 포장에 횡방향으로 프리스트레싱을 가할 때 포장체에 발생하는 응력분포를 분석하여 긴장간격에 따른 특성을 파악하고 종방향과 횡방향 긴장의 상호 영향을 분석하기 위하여 유한요소 모델을 개발하여 구조해석을 수행하였다. 연구결과 횡방향 긴장간격은 작을수록 응력분배를 적절하게 할 수 있고 압축응력의 손실범위를 줄일 수 있으나 경제성 문제를 제고하여 적절한 긴장간격을 선정하여야 한다. 포장체의 노견, 주행위치, 중앙부 등의 여러 위치에서 분석한 횡방향 응력분포는 긴장간격이 넓을수록 평균응력과의 차이가 커지며 그 차이는 슬래브 중앙부로 갈수록 감소하게 된다. 횡방향 긴장을 가하면 종방향으로도 추가 긴장력 이 발생하게 되지만 그 크기는 무시 할 수 있을 정도로 작기 때문에 종횡방향 긴장 설계는 독립적으로 수행하여도 타당하다. 또한 횡방향 긴장 설계 시 이러한 긴장에 의한 응력분포를 이용하는 방안에 대해서도 본 논문에 언급하였다.

• 한국도로학회논문집
• /
• 제11권1호
• /
• pp.247-256
• /
• 2009

본 연구는 포스트텐션드 프리스트레스트 콘크리트 포장(PTCP: Post-Tensioned prestressed Concrete Pavement) 공법의 국내 적용을 위해 수행한 시험시공시에 현장실험을 통해 PTCP의 긴장시 구조적 거동을 분석하기 위하여 수행되었다. 실험을 위해 온도측정센서 및 변위측정게이지를 슬래브에 장착하여 환경하중 및 긴장력 도입에 따른 슬래브의 변위변화를 측정하였다. 총 세 차례에 걸쳐 긴장력을 도입하였으며 긴장작업의 적절성을 온도와 변위의 상관관계 횡방향 균열거동, 일일 종방향 변위변화량 등을 분석하여 판단하였다. 실험결과 타설초기 1차 긴장시에는 슬래브와 하부층과의 마찰 및 콘크리트의 소성성질 등의 요인에 의해 슬래브의 양끝단 부분에서만 큰 변위가 발생하였으나 이후 어느 정도의 시간이 경과한 후 가해진 긴장에서는 슬래브 전체에 뚜렷한 변위가 발생되나 여전히 마찰저항의 영향을 받는 것으로 분석되었다. 또한 긴장이 제대로 가해지면 균열이 존재하더라도 비활성화되어 슬래브가 일체의 거동을 나타내었다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 추계 학술논문 발표대회
• /
• pp.169-170
• /
• 2012

It is analyzed that constructability of post-tensioning system applying HDPE greased strand that is greased and coated by high density polyethylene on a bare strand in reactor containment building. The improvement of corrosion resistance by greasing and HDPE coating on a strand makes transportation, handling and installation of tendon to be easier. Therefore, serial and repetitive process of post-tensioning composed of construction preparation, tendon installation, stressing and anchoring, grease injection could be improved parallel and lumping process of installation and grouting, stressing and anchoring.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.387-392
• /
• 2002

In many years, post-tensioning method has been used for structural reinforcement of RC structures due to easy installation and good quality control. This study presents practical application results for the effectiveness of structural post-tensioning reinforcement of the FCM bridge girders, cement silos and building girders. For the FCM bridges deflected excessively at the end of girders, for cement silos cracked vertically at silo surface and for building girders deflected due to heavy load from roof, the external post-tensioning method was used for uplifting deflected girders and closing cracks with increasing resisting capacity of the structures. It was demonstrated that all the items were rehabilitated nearly to the initial construction status according to the field test results.

• Computers and Concrete
• /
• 제17권1호
• /
• pp.67-86
• /
• 2016

Strengthening as well as correcting unsightly deflections of reinforced concrete (RC) beam may be accomplished by retrofitting. An innovative way to do this retrofitting that is proposed in this study utilizes turnbuckle to apply external post-tensioning. This Turnbuckle External Post-Tensioning (T-EPT) was experimentally proven to improve the serviceability and load carrying capacity of reinforced concrete beams. The T-EPT system comprises a braced steel frame and a turnbuckle mechanism to provide the prestressing force. To further develop the T-EPT, this research aims to develop a numerical scheme to analyze the structural performance of reinforced concrete beams with this kind of retrofitting. The fiber method analysis was used as the numerical scheme. The fiber method is a simplified finite element method that is used in this study to predict the elastic and inelastic behavior of a reinforced concrete beam. With this, parametric study was conducted so that the effective setup of doing the T-EPT retrofitting may be determined. Different T-EPT configurations were investigated and their effectiveness evaluated. Overall, the T-EPT was effective in improving the serviceability condition and load carrying capacity of reinforced concrete beam.