• Journal of international Conference on Electrical Machines and Systems
• /
• 제3권3호
• /
• pp.252-255
• /
• 2014

In the case of long-stator linear drives, unlike rotative drives for which speed or position sensors are a single unit attached to the shaft, these sensors extend along the guideway. The position signal transmitted from maglev vehicle can't meet the need of the real-time propulsion control. In this paper the position estimator for propulsion inverter driving long stator linear synchronous motor (LSLSM) in high speed maglev train is proposed. In order to get the higher resolution of the position information transmitted from vehicle, Full order state observer is proposed for position estimator.

• 한국전산유체공학회지
• /
• 제18권4호
• /
• pp.41-46
• /
• 2013

The selection of the optimal position of the flap was performed in order to improve the aerodynamic performance during the take-off and landing processes of aircraft. For this, the existing airfoils of the main wing and flap are selected as the baseline model and the lift coefficients (cl) according to angle of attacks (AOA) were calculated with the change of the position of flap airfoil. The objective function was defined as the consideration of the maximum cl, lift to drag ratio and cl at certain AOA. Then, at 121 experimental points within $20mm{\times}20mm$ domain, two dimensional flow simulations with Spalart-Allmaras turbulence model were performed concerning the AOA from 0 to 15 degree. If the optimal position was located at the domain boundary, the domain moved to the optimal position. These processes were iterated until the position was included in the inside of the domain. From these processes, the flow separation at low AOA was removed and cl increased linearly comparing with that of the baseline model.

• 드라이브 ㆍ 컨트롤
• /
• 제13권1호
• /
• pp.49-53
• /
• 2016

The accurate calculation of bucket tip position has a large influence on showing the motion of an excavator on the display device of the excavator and controlling the excavator automatically. It is generally known that Inertial Measurement Unit (IMU) sensors are more accurate than accelerometer-based sensors while the boom, arm or bucket moves because additional forces beyond gravity add additional acceleration to the sensors. To prove the accuracy difference between the two types of sensors, a position recognition system using an accelerometer-based sensor and an IMU sensor is implemented on the excavator. The experimental results show that the system using the IMU sensor significantly reduces the position recognition error while bucket moves and additional force beyond gravity exists.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.1511-1515
• /
• 2004

Machine vision system plays an important role in factory automation. Its many applications are found in automobile manufacturing industries, as an eye for robotic automation system. In this paper, an automobile position measuring vision system(APMVS) applicable to manufacturing line for under body painting of a car is introduced. The APMVS measures position and orientation of the car body to be sealed or painted by the robots. The configuration of the overall robotic sealing/painting system, design and application procedure, and application examples are described.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2015년도 특별논문집
• /
• pp.9-13
• /
• 2015

While environmental concern is urging shipbuilding industry to reduce pollutant emission, it is necessary to design environmental friendly vessels. LNG as fuel for ship propulsion is proven to be effective way to reduce pollutant emission. In this study, we find optimum position of LNG fuel supply system on AHTS by considering vessel characteristic. Three different positions of fuel supply system are studied in this paper. Factors such as stability, strength and safety are examined in each position of fuel supply system.

• Journal of Power Electronics
• /
• 제11권4호
• /
• pp.464-470
• /
• 2011

In this paper, the feasibility of applying a position sensorless control technique to hybrid electric vehicles (HEVs) is practically evaluated. The proposed position estimator has a straightforward structure with properties that combines the model and the saliency tracking-based rotor position estimation for interior permanent magnet synchronous motors (IPMSMs). The proposed method can be used in the event of sensor loss or sensor recovery to sustain continuity of operations. The developed system takes into account the estimated position transition between two distinct sensorless methods. The transition is enhanced by introducing a synchronized transition algorithm based on a single tracking observer. Extensive experimental results are presented to verify the principles and show a reliable estimation performance over the entire speed range including standstill under 150% load conditions.

• 한국레이저가공학회지
• /
• 제9권3호
• /
• pp.7-13
• /
• 2006

Auto focusing system to find optimized focal position of laser beam used for material process has been investigated by using fiber confocal method. Wavelength of laser diode (LD) and diameter of single-mode fiber are 780nm and $5.3{\mu}m$, respectively. Intensity distributions of beam reflected from the surface of mirror and silicon bare wafer have been observed in a gaussian form. Experimental results show that focal position obtained by LD is shifted from one observed from surface scribed by laser about $80{\mu}m$. It is due to the difference of wavelength and each divergence of between LD and laser used for material process. It is confirmed that auto focusing control system through position calibration has operated steadily.

• 한국지열·수열에너지학회논문집
• /
• 제9권1호
• /
• pp.15-19
• /
• 2013

In this Study, effect of core position, area ratio and orientation of building on energy load is examined using TRNSYS17. This parameters are major parameters of the conceptual design stage. Reference model is square floor plan($1,444m^2$), centered core and 29% core area ratio. As the results, without considering the building orientation, the annual heating load of central building with 1:1 area ratio is lowest ($10.33kWh/m^2yr$) and the annual cooling load of off-central building with 1:1 area ratio is lowest ($59.27kWh/m^2yr$). As area ratio is bigger, cooling load is lower and heating load is higher. But if we consider building orientation, orders of heating load and cooling load are changed for area ratio and orientation.

• 한국산학기술학회논문지
• /
• 제14권10호
• /
• pp.4739-4746
• /
• 2013

본 논문에서는 초고속 자기부상철도 추진 제어에 필수적인 차량의 위치검지에 있어서 위치신호 송신지연 및 송신주기가 추력에 미치는 영향을 수치적으로 분석하고 test bed를 이용한 실험을 통해 이를 확인하였다. 위치신호 송신문제를 해결하기 위한 방안으로서 위치신호 보상 및 추정 기법을 제시하였으며 제시된 방법을 test bed에 적용하여 효용성을 검증하였다. 적용 결과 추력이 크게 증가하였으며 이에 따라 차량의 가속도 및 속도 성능이 향상됨을 확인하였다. 본 방법은 향후 개발 예정인 한국형 초고속 자기부상철도의 위치검지시스템에 효과적으로 사용될 수 있을 것으로 판단된다.

• 한국항공우주학회지
• /
• 제45권4호
• /
• pp.276-283
• /
• 2017

본 논문은 4개의 로터를 가지는 쿼드콥터에 대한 비선형 운동모델을 구성하고, 특이섭동 기법을 이용한 모델 역변환 위치 제어기 설계 결과에 대해 나타낸다. 특이섭동 모델 역변환방식은 느린 동역학과 빠른 동역학을 시분할 기법(time scale separation)기법을 이용하여 각각 역변환 시키는 방법이다. 수립한 6자유도 비선형 운동모델 기반으로, 모델 역변환 제어기를 설계하고 시뮬레이션을 수행한 결과 정확한 위치 추종을 수행함을 확인하였다.