• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.11 no.1
• /
• pp.29-35
• /
• 2017

It was hard for a conventional care-bed to be realized to a low-floor position due to a complex actuation mechanism installed under the mattress support platform. In this paper a mechanism design to set a low-floor position as well as to adjust back- and leg-rest angles was proposed. A dual motor was applied to the back- and leg-rest mechanism of which design parameters were determined by an optimal method. An elevation mechanism was also designed to enlarge a limited stroke range up to two times of its original stroke using a pulley mechanism. An evaluation test was performed by five healthy subjects ($24.4{\pm}0.5yrs.$) when going up from a floor position to a preset best position which was set to the 240mm height for a prototype low-floor bed and to the 600mm height for a conventional bed. As a result, the moving distance was 38% lower than the conventional bed when the subject used the low-floor bed. It showed that the low-floor care-bed reduced physical burdens and was effective to assist activities of daily living of the elderly people.

• Journal of the Korean Society of Radiology
• /
• v.12 no.3
• /
• pp.397-402
• /
• 2018

The study best image for diagnosis of fracture, dislocation and unilateral degenerative arthritis of the Sacroiliac joint, this study was performed to obtain the best image of the joint space of the hip joint by giving angle change to the pelvis phantom and the x-ray tube. I received evaluation. The results of the Receiver Operating Characteristic that in the case of simple photographs for the detection of joint arthritis and degenerative arthritis in the prone position, the photograph taken in the prone position raises the buttocks of the opposite side of the test by $25^{\circ}{\sim}30^{\circ}$ and the x-ray tube is perpendicular to the sagittal plane passing 2.5 cm inward from the thorny vertebra In the lying position, lift the Sacroiliac joint of the test side by $25^{\circ}{\sim}30^{\circ}$, and take a $5^{\circ}$ angle of the x-ray tube angle toward the foot toward the center of the upper bruch spine from it will be helpful to diagnose arthritis. the center of the upper bruch spine to the side of the ankle joints in the transverse direction And posterior direction, it will be helpful to diagnose arthritis.

• The korean journal of orthodontics
• /
• v.26 no.2 s.55
• /
• pp.197-204
• /
• 1996

This study was performed to mark the criteria of the eathetic smile that was necessary to improve the esthetic problem in oral maxillo-facial region. The facial straight photographs of 62 adults(30 males, 32 females : 19-24 years old) in resting position and during smile were taken. The measurements and proportion of lip-teeth relationship during smile were statistically analyzed with photogrammetry. The following results wow obtained : 1. In the evaluation of the change of lips, smile line ratio was 0.93, buccal corridor ratio was 0.63, and smile symmetry ratio was 0.96. 2. The width of mouth during smile was 1.31 times of the width inthe resting position and 0.48 times of face width. 3. The upper lip height during smile was 0.69 times of the height in the resting position and the lower lip height during smile was 0.93 times of the height in the resting position. 4. The mean exposed lenght of upper central incisor was 9.96mm. Maxillary incisor exposure was significantly correlated with the upper lip change ratio, mouth width change ratio, and buccal corridor ratio.

• Journal of Fashion Business
• /
• v.25 no.3
• /
• pp.144-158
• /
• 2021

The purpose of this study is to develop a bodice block suitable for women in their 20s with turtle neck syndrome. The problem of turtle neck syndrome body type was derived through the evaluation of bodice blocks. First, the length of the front bodice was longer and the length of the back bodice was shorter. Second, the front neck point, back neck point, and the shoulder line were not in place. Third, the side neck was pushed up. Fourth, the length of armhole was long and it floated. Fifth, the front hem was attached to the body and the back hem was away from the body. A finally developed pattern was designed by developing four test patterns to solve the problem that appeared in a selected bodice pattern, and a t-test was conducted to determine the difference in the appearance evaluation by virtual clothing between the two patterns, bodice block and the development pattern. According to the result, the fit was not good from the side body because the position of the side neck point was not in a place due to the characteristics of the body shape of turtle neck syndrome, but the problems of the anterior neck position, the position of the back neck point, the shoulder line position, and the armhole shape were improved in the developed pattern.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.11
• /
• pp.985-993
• /
• 2014

This paper suggested a new evaluation method for optimal HUD position through a correlation based on between biological signal as and statistical analysis which using (Electroencephalogram, EEG) and ANOVA. This experiment was conducted two kinds of method to evaluate the optimal HUD position. At first, visual stimulus suggested from six different positions(the top and the bottom of the left, the top and the bottom of the center and the top and the bottom of the right on the screen) in laboratory and an object image was shown for 30 seconds in a screen which has $235{\times}197cm2$ size. And second, HUD image was configured from three different positions and an object image was shown for 30 seconds in a screen. EEG, which used ${\alpha}$-wave and ${\beta}$-wave for evaluate an emotional stability, were measured from Fp1, Fp2, F7 and F8 channel based on ten to twenty electrode system. From the result in laboratory, F7 ${\beta}$-wave was shown statistically significant to significance probability of 0.006 and between ${\alpha}$-wave and ${\beta}$-wave were showed a negative correlation(r=-0.190). Also, Both the top of left and the bottom of center were showed lower ${\beta}$-wave than the bottom of right. From the result in railway simulator, Fp1 ${\beta}$-wave was appeared statistically significant as significance probability of 0.033 and it was showed lower ${\beta}$-wave than center. The outcome of this study will be helpful about evaluation of optimal HUD position through correlation between alpha wave and beta wave.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.2
• /
• pp.97-107
• /
• 2017

This study is the second investigation on the steady flow characteristics of an SI engine with a semi-edge combustion chamber as a function of the port shape with varying evaluation positions. For this purpose, the planar velocity profiles were measured from 1.75B, 1.75 times of bore position apart from the bottom of head, to 6.00B positions using particle - image velocimetry. The flow patterns were examined with both a straight and a helical port. The velocity profiles, streamlines, and centers of swirl were almost the same at the same valve lift regardless of the measuring position, which is quite different from the case of the pent-roof combustion chamber. All the eccentricity values of the straight port were out of distortion criterion 0.15 through the lifts and the position. However, the values of the helical port exceeded the distortion criterion by up to 4 mm lift, but decreased rapidly above the 3.00B position and the 5 mm lift. There always existed a relative offset effect in the evaluation of the swirl coefficient using the PIV method due to the difference of the ideal impulse swirl meter velocity profile assumption, except for the cylinder-center-base estimation that was below 4 mm of the straight port. Finally, it was concluded that taking the center as an evaluation basis and the assumption about the axial velocity profile did not have any qualitative effect on swirl evaluation, but affected the value owing to the detailed profile.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.22 no.1
• /
• pp.77-84
• /
• 1992

The purpose of this study was to evaluate the diagnostic value of panoramic radiography for diagnosis of temporomandibular joint. Five dry skulls were selected for this study and artificial osteophyte was attached to four different areas of the mandibular condylar head. And then, the author had taken panoramic radiographs with the head in conventional position, 25㎜ forward position and reverse position in mouth opening state. Three dental radiologists evaluated the radiographic images of osteophyte in 60 panoramic radiographs. The results were as follows: In conventional position, osteophyte on the anterolateral and anterocentral area of the condylar head was best seen (p<0.01). In 25㎜ forward position, osteophyte on the anterocentral and anteromedial area was best seen (p<0.05). In reverse position, osteophyte on the anterocentral area was best seen (p<0.05). Osteophyte on anteromedial area was better seen in 25㎜ forward position than in conventional position (p<0.05).

• Progress in Medical Physics
• /
• v.28 no.2
• /
• pp.39-44
• /
• 2017

This study aims to analyze dose distribution and treatment time of endobronchial brachytherapy (EBBT) by changing the position step size of the dwell position. A solid water phantom and an intraluminal catheter were used in the treatment plan. The treatment plans were generated for 3, 5, 7, and 10 cm treatment lengths, respectively. For each treatment length, the source position step sizes were set as 2.5, 5, and 10 mm. Three reference points were set 1 cm away from the central axis of the catheter, along the axis, for uniform dose distribution. Volumetric dose distribution was calculated to evaluate the dosimetric effect. The total radiation delivery time and total dwell time were estimated for treatment efficiency, which were increased with position step sizes. At half-life time, the differences between the position step sizes in the total radiation delivery time were 18.1, 15.4, 18.0, and 24.0 s for 3, 5, 7, and 10 cm treatment lengths, respectively. The dose distributions were more homogenous by increasing the position step sizes. The dose difference of the reference point was less than 10%. In brachytherapy, this difference can be negligible. For EBBT, the treatment time is the key factor while considering the patient status. To reduce the total treatment time, EBBT can be performed with 2.5 mm position step size.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.13 no.4
• /
• pp.476-490
• /
• 1991

Although various technical details of the surgical procedures have been improved, Skeletal relapse is the most noteworthy complication of orthognathic surgery. It seems to be an imbalance of the perioral muscular groups resulting from changes in the cavitas oris propria after surgery. Among other factors, it is widely known with the changes of tongue posture, as indicated by the hyoid position. Ten patients that had undergone mandibular setbacks by way of Modified Obwegeser method were evaluated retrospectively. The serial cephalometric films were taken preoperatively, immediately postoperatively, after removal of IMF, and at a subsequent long-term follow-up period. The cephalometric evaluation of tongue posture were based on stable craniofacial landmarks. The relation between the 2-dimensional changes of tongue posture and hyoid position and the relapse of mandibular setback are discussed. Anatomic changes that were found to accompany such setback are as follows. 1.There are 2 cases of relapse in 10 patients at long-term follow-up(20%) 2.The tongue was moved posteriorly and its size was reduced anteriorly and posteriorly at immediate postoperative change and then the mandible shifted slightly toward the preoperative position, but the long was adapted to its new environment due to changing the position of its posterior part, and also the hyoid that moved posterioly and inferiorly was stabilized sightly posteriorly than its original position. 3.On the distance change of the suprahyoid muscle, the distance of P-H, ST-H was increased at immediate postoperative change(p<0.01) and decreased at IMF period(p<0.001), but the distance of H-Me, H-Ge was slightly decreased at IMF and long-term period(p<0.05). 4.On the width change of the pharyngeal air way, the width of the upper part of the pharyngeal space was lightly contracted at IMF and long-term period(p<0.05). 5.On the relation between mandibular setback and tongue posture and hyoid position, the significant correlation was found between the changes of some parts of mandibular setback and those of tongue posture, and not found those of hyoid position.

• Spatial Information Research
• /
• v.9 no.2
• /
• pp.263-275
• /
• 2001

With increasing of utilization of 1/1,000 Digital-Map being constructed with NGIS project, it is entering upon the stage that problem as the inspection of position accuracy of Digital-Map before its use. This paper evaluated position accuracy of Digital-Map being based on the construction of college facility management system into small area and presented modification/renovation of Digital-Map on area being occurred position error. With a view to evaluation of position error to building using RTK survey, position error was shown more than 0.5mm that is prescribed in survey-law. In order to acquire good position accuracy, first we carried out Static survey to college and selected control point. And, we evaluated coordinate value to important building from control point and compared these results with RTK survey results. Second, we carried out Affine transform based on the control point of building being surveyed with RTK, transformed pre-constructed Digital-Map and compared these results with RTK Survey results. We analyzed first and second method and presented improvement method of position accuracy of Digital-Map suited on small area.