• Journal of Positioning, Navigation, and Timing
• /
• v.11 no.4
• /
• pp.229-238
• /
• 2022

This paper addresses on the International technical trends, standards, and development status of terrestrial radionavigation system to provide more accurate and fail-safe Positioning, Navigation, and Timing (PNT) Information available in maritime navigation environment. We analyze the performance result of pilot service in enhanced Long range navigation (eLoran) testbed environment using Low Frequency (LF) signal, and describe the development status of Ranging-Mode (R-Mode) system using Medium Frequency (MF) and Very High Frequency (VHF) to meet the Harbor Entrances and Approaches (HEA) requirement of International Maritime Organization (IMO) within 10m position accuracy. Furthermore, we present an architecture for integrated service of satellite-terrestrial navigation system and future maritime applicable fields. As the core information infrastructure of future navigation for 4th industrial revolution, this paper will be contributed to determining the direction of present and future to provide fail-safe PNT service with Global Navigation Satellite System (GNSS) based on the technical enhancement of terrestrial integrated navigation system.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.16 no.3
• /
• pp.187-196
• /
• 2000

This study was performed to offer convenience to determine the vertical dimension of occlusion of edentulous patients by investigating the interocclusal distances at physiologic rest position, at speaking of /m/ sound, and some korean short sounds, that is, /mem/ and /beb/ sounds, which were found in our previous study with dentulous subjects. Ten edentulous subjects - 6 men and 4 women - were selected for this study. The frequencies at speaking of /m/, /mem/, and /beb/ sounds were analyzed with Computerized speech lab($CSL^{TM}$, Model 4300B, Software version 5.X, Kay Elemetrics Co. U.S.A.). And the interocclusal distances at physiologic rest position and at speaking of /m/, /mem/, and /beb/ sounds were measured with K6 diagnostic system(Myo-tronics, Inc. U.S.A.). The results of this study were as follows ; 1. In the acoustic analysis by Computerized speech lab, frequencies of sounds of edentulous subjects with complete denture at speaking of /m/, /mem/, and /beb/ were similar to those of dentulous subjects. 2. In the linear correlation by Pearson's correlation coefficient, the interocclusal distance at physiologic rest position was most similar to those of speaking /mem/ sound, secondly /m/ sound, and thirdly /beb/ sound(p<0.05). In reliability by Cronbach's alpha, the results were reliable with alpha value 0.97. 3. It was found by Levene's test for equality of variance that the difference between men and women in the interocclusal distances at physiologic rest position and at speaking of /m/, /mem/, and /beb/ sounds was not statistically significant(p>0.05).

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.3 no.1
• /
• pp.35-41
• /
• 1983

The purpose of this study is to provide a method of estimating the frequency of flood magnitudes in ungauged station. Six major station are selected for this study in the Geum River system. For each gauging station in the basin, T-year flood is determined by Weibull plotting position. The derivation of the flood frequency formulae is performed on the basis of estimating method of floods with using the hydrological and geomorphical factors developed by U.S. Geological Survey. It is found that the model in this study can be applied to flood flow estimation of ungauged station in the Geum River basin because the mean characteristics of flood flow is used for the basin.

• Journal of the Korea Society for Simulation
• /
• v.28 no.2
• /
• pp.71-79
• /
• 2019

This research proposes an automatic generation system of aimpoints with considering 3D target shapes and CEP(circular error probability) values after determining a target and an azimuth value. In the past, users decided aimpoints manually based on experience or just chose a middle point of the 3D model. Futhermore, it was not possible to select a proper position with consideration of azimuth because users should decide aimpoints before the azimuth value was determined. To solve this problem, this research provides a automatic system to compute proper aimpoints with 3D target shapes, azimuth values and CEP. This article contains the explanation of 3 steps for generating aimpoints automatically: first, generating a reference plane and candidate entry points, then computing scores of each entry points and finally determining an aimpoint from the entry point with the highest score. Users can easily determine a final aimpoint with high probability of success using this system.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2006.05a
• /
• pp.56-58
• /
• 2006

Camera calibration in machine vision is the process of determining the intrinsic cameara parameters and the three-dimensional (3D) position and orientation of the camera frame relative to a certain world coordinate system. On the other hand, Takagi-Sugeno-Kang (TSK) fuzzy system is a very popular fuzzy system and approximates any nonlinear function to arbitrary accuracy with only a small number of fuzzy rules. It demonstrates not only nonlinear behavior but also transparent structure. In this paper, we present a novel and simple technique for camera calibration for machine vision using TSK fuzzy model. The proposed method divides the world into some regions according to camera view and uses the clustered 3D geometric knowledge. TSK fuzzy system is employed to estimate the camera parameters by combining partial information into complete 3D information. The experiments are performed to verify the proposed camera calibration.

• Journal of Astronomy and Space Sciences
• /
• v.22 no.1
• /
• pp.35-46
• /
• 2005

This paper addresses the design and analysis results of a 2-axes magnetometer for attitude determination of small satellite. A low-cost and efficient 2-axes fluxgate magnetometer was selected as the most suitable attitude sensor for LEO microsatellites which require a low-to-medium level pointing accuracy. An optimization trade-off study has been performed for the development of 2-axes fluxgate magnetometer. All the relevant parameters such as permeability, demagnetization factor, coil diameter, core thickness, and number of coil turns were considered for the sizing of a small satellite magnetometer. The magnetometer which is designed, manufactured, and tested in-house as described in this paper satisfies linearity requirement for determining attitude position of small satellites. On the basis of magnetometer which is designed in Space System Research Lab. (SSRL), commercial magnetometer will be developed.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.6
• /
• pp.675-681
• /
• 2015

When many holes on a plane are machined simultaneously, the positional precision and machining efficiency are very important. Multi-spindle heads are typical order making products of which the number of shafts and hole positions vary depending on the size or form of the product. For the automatic design of multi-spindle heads, the design modules for power transmission systems for drive, idle, and spindle shafts were developed, and a design technique the determining the optimum position and number of idle shafts according to gear positions was developed. In addition, for the precise determination of the multi-spindle head, the design methods for the guide planes of columns, and feed mechanisms were devised. In addition, the design modules for accurate clamping and automatic transportation mechanisms were developed. Finally, in order to simplify and standardize the design process, the design analysis and simulation verification modules are integrated.

• Journal of Institute of Control, Robotics and Systems
• /
• v.8 no.9
• /
• pp.812-817
• /
• 2002

This paper presents a development of high accuracy aligner and describes a method to find the orientation of a substantially circular disk shaped wafer with at least one flat region on an edge thereof. In the developed system, the wafer is spun one 360 degree turn on a chuck and the edge position is measured by a linear array to obtain a set of data points at various wafer orientation. The rotation axis may differ from wafer center by an unknown eccentricity. The flat angle is found by fitting a cosine curve to the actual data to obtain a deviation. The maximum deviation is then corrected for errors due to a finite number of data points and wafer eccentricity by calculating an adjustment angle from data points on the wafer fiat. After determining the flat angle the wafer is spun to the desired orientation. The wafer eccentricity can be calculated from four of the data points located away from the flat edge region. and the wafer is then centered.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10b
• /
• pp.1758-1763
• /
• 1991

This paper describes a new method to determine the 3D-shape of objects consisting of specular planar surfaces. This method exploits a light source which is made of a diffuse plane with a grid pattern encoded in an M-sequence and uses a single image of the light source reflected by the objects to acquiring orientations and positions of the surfaces of the objects. When grid lines of the light source are reflected by a specular planar surface and perspectively projected on an image plane, a set of lines vanishing at a point are obtained on the image plane. The orientation of the specular planar surface is determined by using the vanishing point, and the position is determined by using the correspondence between lines on the image and lines on the light source, which is obtained by employing a characteristic regularity of the M-sequence. Before the vanishing points are calculated, the lines on the image are classified and correlated with the surfaces of objects by using slopes and positions of the lines and the regularity of the M-sequence. This method requires only a single image.

• Journal of Technology Innovation
• /
• v.6 no.1
• /
• pp.187-214
• /
• 1998

This paper tries to examine the effectiveness of inventory reduction to the productivity increase and the impact of production environments on its effectiveness utilizing the Profit Impact of Market Strategy (PIMS) Database from the Strategic Planning Institute, a large data set that covers a variety of manufacturing activities from the early 1970s to late 1980s. The empirical results of this paper support the robustness of the principle of "Lean Production" or JIT system (also referred to as "Stockless Production"). We also find that the overall environment in which manufacturing strategic business units operate is an important factor in determining the different degrees of effectiveness of the work-in process (and raw materials) invertory reductions. In particular, we find that the effectiveness of the work-in process reduction varies according to the position in the product life cycly as well as the complexity and characteristics of the production processes.roduction processes.