• Journal of international Conference on Electrical Machines and Systems
• /
• v.2 no.1
• /
• pp.97-103
• /
• 2013

This paper describes the characteristics of Electronic Throttle Controller (ETC) module in BLDC motor without the hall sensor for detecting a rotor position. The proposed ETC control system, which is mainly consisted of a BLDC motor, a throttle plate, a return spring and reduction gear, has a position sensor with an analogue voltage output on the throttle valve instead of BLDC motor for detecting the rotor position. So the additional commutation information is necessarily needed to control the ETC module. For this, the estimation method is applied. In order to improve and obtain the high resolution for the position control, it is generally needed to change the gear ratio of the module or the electrical switching method etc. In this paper, the 3-phase switching between successive commutations is adapted instead of the 2-phase switching that is conventionally used. In addition, the position control with a variable PI gain is applied to improve a dynamic response during a transient period and reduce vibration at a stop in case of matching position reference. The mentioned method can be used to estimate the commutation state and operate the high-precision position control for the ETC module and the high response characteristics. The validity of the proposed method is examined through the experimental results.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1008-1013
• /
• 2005

In this paper, position tracking control of an autonomous helicopter is presented. Velocity is controlled by using an optimal state controller LQR. A position control loop is added to form a PD controller. To minimize a position tracking error, neural network is introduced. The reference compensation technique as a neural network control structure is used, and a position tracking error of an autonomous helicopter is compensated by neural network installed in the remotely located ground station. Considering time delays between an autonomous helicopter and the ground station, simulation studies have been conducted. Simulation results show that the LQR with neural network compensation performs better than that of the LQR itself.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.117.4-117
• /
• 2002

This paper describes a stationary position control of a wheeled blimp. The wheeled blimp is composed of a blimp filled with helium gas and a wheeled vehicle part. The wheeled blimp is designed to enable both flying in the air and standing on the floor. The wheeled blimp stands on the floor keeping its balance. However, it is difficult for the wheeled blimp to maintain a stationary position in standing phase since the stationary blimp system responds sensitively to air current even in indoor environments. In order to keep the stationary position restraining motion caused by an uncertain airflow, a position controller for the wheeled blimp is needed. Controller design based on dynamic m...

• Transactions of The Korea Fluid Power Systems Society
• /
• v.5 no.4
• /
• pp.32-37
• /
• 2008

For the bucket tip position control of the excavator, a traditional hydraulic excavator system was exchanged into an electro-hydraulic one. EPPR valves are attached to the traditional MCV and hydraulic joysticks are replaced by electronic ones to develop the electro-hydraulic system. To control the electronic pump with a good performance, the control logic for the pump is deduced from the AMESim simulation and the experimental method on the test bench. To get a good position control performance of the excavator bucket tip, PI+AntiWindup controller is selected as a position controller. The experimental results showed the good controllability for the electro-hydraulic excavator system on the test bench.

• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.64-66
• /
• 1999

Switched reluctance motor(SRM) has the advantages of simple structure, low rotor inertia and high efficiency. However, position sensor is essential in SRM in order to synchronize the phase excitation to the rotor position. The position sensors increase the cost of drive system and tend to reduce system reliability. This paper investigates the speed control of sensorless SRM in which the phase current and change rate are utilized in position decision, and the period of dwell angle is variable by compensating the rotor angle. The proposed system consists of position decision, phase locked loop controller, switching angle controller and inverter. The performances in the proposed system are verified through experiments.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.684-686
• /
• 2000

Switched reluctance motor(SRM) has the advantages of simple structure, low rotor inertia. and high efficiency. However position sensor is essential in SRM in order to synchronize the phase excitation to the rotor position. The position sensors increase the cost of drive system and tend to reduce system reliability. This paper investigates the speed control of sensorless SRM in which the phase current and change rate are utilized in position decision, and the period of dwell angle is variable by compensating the rotor angle for speed control. The proposed system consists of position decision. phase locked loop controller, switching angle controller and inverter. The performances in the proposed system are verified through the experiment.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.7 no.4
• /
• pp.34-41
• /
• 1993

The dc servo motor has been often used as the driver for a position control system, because the performance of the control is excellent on the speed and position control. When the unknown disturbance and/or the varying quantity of load is imposed on the position control system, the response of the system has the steady and/or the transient state error.The objective of this work is to demonstrate the principles, design methodologies and implementation of a servo controller for reducing the error in the position control system using the dc servo motor. The coefficients of a servo controller are computed by the pole placement.

• Journal of the Korean Society of Industry Convergence
• /
• v.22 no.4
• /
• pp.435-445
• /
• 2019

Ball screw drives are widely used in industry, and many studies have been devoted on precise, fast and robust control of ball screw drives. In this study, a novel position control algorithm for ball screw drives is proposed, which consist of a PD controller, a friction feedforward and a disturbance observer. The dynamics and the position error of such controller are analyzed to establish an error model, which can be used to predict the resulting position error of the given desired trajectory. Using the proposed error model, the desired trajectory can be modified so that the predicted position error can be compensated in a feedforward manner. The proposed algorithm does not require the model of the system for the error prediction, and thus can be easily applied to conventional control systems. The performance of the system is verified through simulations and experiments.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.5
• /
• pp.143-152
• /
• 1994

The velocity trajectory profile of trolley is designed to minimize both swinging while transportation of load and the stop position error at the final stop position. This profile is designed to be automatically programmed by the digital control algorithm when the length of chain and the desired travel distance are given as a priori. Also, to minimize both swinging and the stop position error the anti-swing controller which improves poor damping characteristics of the crane and the stop position controller are employed. The experimentalresults of sequential adaptation of the velocity trajectory profile and these two controllers show that this control scheme has excellent control performance as compared with that of the uncontrolled crane system.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.61-65
• /
• 2000

In this paper We have developed the high-speed controller for haptic control. The proposed controller is based on the PCI/FPGA technology which can calculate the real position and transmit the force data to device rapidly. The haptic system is composed of 6DOF force display device high-speed controller. The developed system will be used on constructing the dynamical virtual environment. To show the efficiency of our system we designed simulation program of force-reflecting. As the result of the experiment we found that the controller has much higher resolution than some other controller It is so efficient in a 1 PC-based system with 1[kHz] haptic interrupt cycle.