• Journal of Welding and Joining
• /
• v.27 no.1
• /
• pp.71-78
• /
• 2009

In the circumferential welding of pipe, welding phenomenon changes with the position of pipe. Especially in the overhead position, back bead of vertical-up position would be sunk. To investigate the size of back bead and keyhole with the change of the flow rate of pilot and shield gas at each position, bead-on plate welds were conducted on 6mm thickness SS400 with inclined-up position. When the rest of welding conditions remained constant, the width of back bead was increased as the flow rate of pilot gas was increased. And back bead tended to convex as the flow rate of shield gas was increased.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1299-1306
• /
• 2007

The combination of laser beam and electric arc sharing common weld pool has widely been investigated since the late seventies, but it is beginning of the industrial uses. Recently, laser-GMA hybrid welding process showed possibility to overcome the tight gap tolerance with improved productivity. The laser-arc hybrid welding process is inherently complex because it has three kinds of process parameters: arc welding, laser welding and hybrid welding parameters. In this study, the optimum range of the process parameters were determined by high speed image analysis which could unveil the welding phenomena in laser-arc hybrid welding. The laser-arc hybrid welding was applied for position welding from the flat position to the overhead position and the welding characteristics were investigated.

• Journal of Welding and Joining
• /
• v.33 no.1
• /
• pp.54-60
• /
• 2015

Laser-arc hybrid welding has been considered as an effective pipe girth welding process since early 2000's. Tolerance for fit-up offsets such as gap and edge misalignment is one of most important requirements in pipe girth laser-arc hybrid welding, and several approaches using parameter optimization, a laser beam scanning and an arc oscillation have been tried. However the required offset tolerance has not been fully accomplished up to now and laser-arc hybrid welding has not been widely applied in pipeline construction than expected, despite of its high welding speed and deep penetration. In this study, internal welding was adopted to ensure the offset tolerance and sound back bead. The effect of welding parameters on bead shape was investigated at the flat position. Also tolerances for gap and edge misalignment were verified as 0.5 mm and 2.0 mm, respectively. The position welding trials were conducted at several welding positions from the flat to the overhead position in a downward direction. With the fixed welding speed, arc current for gas metal arc welding current and laser output power, adequate welding voltages for gas metal arc welding were suggested for each position.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.361-364
• /
• 1997

There has been requested to automate the welding process in shipyard due to its dependence on skilled operators and the inferior working environments. According to these demands, multiple robot welding system for sub-assembly welding line has been developed, realized and installed at Keoje Shipyard. In order to realize automatic welding system, robots have to be equipped with the sensing system to recognize the position of the welding panels. In this research, a camera vision system is developed to detect the position of base panels for subassembly line in shipbuilding. Two camera vision systems are used in two different stages (Mounting and Welding) to automate the recognition and positioning of welding lines. For automatic recognition of panel position, various image processing algorithms are proposed in this paper.

• Journal of Institute of Control, Robotics and Systems
• /
• v.5 no.3
• /
• pp.344-352
• /
• 1999

There has been requested to automate the welding process in shipyard due to its dependence on skilled operators and the inferior working environments. According to these demands, multiple robot welding system for sub-assembly welding line has been developed, realized and installed at Keoje shipyard. In order to realize automatic welding system, robots have to be equipped with a sensing system to recognize the position of the welding panels. In this research, a camera vision system(CVS) is developed to detect the position of base panels for sub-assembly line in shipbuilding. Two camera vision systems are used in two different stages (fitting and welding) to automate the recognition and positioning of welding lines. For automatic recognition of panel position, various image processing algorithms are proposed in this paper.

• Journal of Welding and Joining
• /
• v.16 no.5
• /
• pp.119-133
• /
• 1998

To implement full automation in pipe welding, it si most important to develop special sensors and their related systems which act like human operator when detecting irregular groove conditions. In this study, an automatic pipe Gas Metal Arc Welding (GMAW) system was proposed to full control pipe welding procedure with intelligent sensor systems. A five-axes manipulator was proposed for welding torch to automatically access to exact welding position when pipe size and welding angle were given. Pool status and torch position were measured by using a weld-pool image monitoring and processing technique in root-pass welding for weld seam tracking and weld pool control. To overcome the intensive arc light, pool image was captured at the instance of short circuit of welding power loop. Captured image was processed to determine weld pool shape. For weld seam tracking, the relative distance of a torch position from the pool center was calculated in the extracted pool shape to move torch just onto the groove center. To control penetration of root pas, gap was calculated in the extracted pool image, and then weld conditions were controlled for obtaining appropriate penetration. welding speed was determined with a fuzzy logic, and welding current and voltage were determined from a data base to correspond to the gap. For automatic fill-pass welding, the function of human operator of real time weld seam control can be substituted by a sensor system. In this study, an arc sensor system was proposed based on a fuzzy control logic. Using the proposed automatic system, root-pass welding of pipe which had gap variation was assured to be appropriately controlled in welding conditions and in torch position by showing sound welding result and good seam tracking capability. Fill-pass welding by the proposed system also showed very successful result by tracking along the offset welding line without any control of human operator.

• Journal of Welding and Joining
• /
• v.28 no.6
• /
• pp.21-27
• /
• 2010

Due to excellent weld quality, orbital welding with TIG is widely applied to pipe welding. But concave back bead is formed easily in overhead and inclined-up position of butt orbital welding. It is difficult to find a paper to overcome this problem. In this study, in order to make convex back bead in overhead and inclined-up position of pipe 5G welding, control method of molten pool was actively investigated. Melt run welds were conducted on thickness 4.0mm SS400 with overhead and inclined-up position and was observed the variation of bead shape after welding with the bead former developed. The height of back bead showed the trend of increase as the distance from molten pool to the bead former was decreased. Also, there is no trend in the bead width of front and back as welding position was changed or the distance from molten pool to the bead former was decreased.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.36-38
• /
• 2007

The instability of the arc in the $CO_2$ arc welding affects the quality of the weld in the automotive industry. This paper evaluates the effects of the arc stability in $CO_2$ arc welding with respect to vertical welding positions. In this experiment, galva-annealed steel sheets(CA) were used as specimens, and these materials were welded by adopting new Cold Metal Transfer (CMT) process. For each sample, fillet joint welding trials were carried out using the same conditions. Each part of welding joints was welded with vertical-up, vertical-down position at $45^{\circ},\;90^{\circ}\;and\;135^{\circ}$ degrees. A high speed camera and a welding signal monitoring system were used for monitoring fluid-flow phenomena in weld pools and frequency measurements, respectively. Through this study, the welding position were found to be key factors mainly to influence the arc stability in $CO_2$ welding moreover and that the arc stability in the vertical-up welding position was observed to be more stable than the vertical-down welding position below $90^{\circ}$.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.680-684
• /
• 1996

Welding systems cannot adapt to changes in the joint geometry which may occur due to a variety of reason. Automatic seam tracking technigue is essential to adjust the welding torch position in real time as it moves along the seam. Automatic tracking system must keep the welding speed constant unrelation to the change of the welding path. Therefore, the information from the laser displacement sensor must be converted into the input to operate the X-Y table and to rotate the desired torch position by proposed algorithm. In this research, laser displacement sensor is used as a seam finder in the automatic tracking system. X-Y moving table manipulated by ac servo motor controls the position and velocity of the torch-and-sensor part. DC motor controls the position and velocity of the torch. X-Y table controls the position of sensor and relative position of torch is controlled by dc motor which is mounted at sensor-and-torch part. Sensor is always ahead of torch to preview the weld line. From the experimental results, we could see the possiblity that the laser displacement sensor can be used as a seam finder in welding process and that the seam tracking system controlled by proposed algorithm is well done.

• International Journal of Korean Welding Society
• /
• v.1 no.1
• /
• pp.31-38
• /
• 2001

For the horizontal fillet welding with one plate in a vertical position, there will be a higher tendency of weld metal falling down rather than for the butt-welding in flat position. Such phenomenon could bring about the overlap or deflection of weld pool, and consequently induce the poor mechanical strength of weldments. Therefore, a precise position control of welding torch in conjunction with the weld qualify plays an important role in welding robot applications. In the present study, an experimental method was proposed for deriving a mathematical model between the leg length and the welding conditions. Finally, an algorithm was proposed for weld seam tracking and improvement of the weld quality. The reliability of the proposed algorithm was evaluated through various experiments, which showed that the proposed algorithm can be very effective for tracking the weld line and simultaneously achieving the sound weld bead.