• Journal of Radiation Protection and Research
• /
• v.36 no.1
• /
• pp.28-34
• /
• 2011

The measurement-based verification for intensity modulated radiation therapy (IMRT) is a time-and labor-consuming procedure. Instead, this study aims to develop a MU fluence reconstruction method for IMRT QA. Total actual fluences from treatment planning system (TPS, Eclipse 8.6, Varian) were selected as a reference. Delivered leaf positions according to MU were extracted by the dynalog file generated after IMRT delivery. An in-house software was develop to reconstruct MU fluence from the acquired delivered leaf position data using MATLAB. We investigated five patient's plans delivered by both step-and-shoot IMRT and sliding window technologies. The total actual fluence was compared with the MU fluence reconstructed by using commercial software (Verisoft 3.1, PTW) and gamma analysis method (criteria: 3%/3 mm and 2%/1 mm). Gamma pass rates were $97.8{\pm}1.33$% and the reconstructed fluence was shown good agreement with RTP-based actual fluence. The fluence from step and shoot IMRT was shown slightly higher agreement with the actual fluence than that from sliding window IMRT. If moving from IMRT QA measurements toward independent computer calculations, the developed method can be used for IMRT QA. A point dose calculation method from reconstructed fluences is under development for the routine IMRT QA purpose.

• Journal of Astronomy and Space Sciences
• /
• v.20 no.1
• /
• pp.29-42
• /
• 2003

The KSR-3 magnetometers consist of the fluxgate magnetometer (MAG/AIM) for acquiring the rocket flight attitude information, and the search-coil magnetometer (MAG/SIM) for the observation of the Earth's magnetic fluctuations. The position (latitude, longitude, and height) and flight condition (the transformation angle) of the rocket is measured after the data based on these two magnetometers are compared with IGRF The gap in the vector of magnetic field between the position of the launching point and an impact point is taken into account in data reduction. Angular variation of pitch, yaw, and roll can be researched when the data is applied to the coordinate system of the rocket.

• Physical Therapy Korea
• /
• v.16 no.3
• /
• pp.9-15
• /
• 2009

The purpose of this study was to examine contraction of abdominal muscles on surface electromyographic (EMG) activity of superficial cervical flexors, rib cage elevation and angle of craniocervical flexion during deep cervical flexion exercise in supine position. Fifteen healthy subjects were participated for this study. All subjects performed deer cervical flexion exercise with two methods. The positions of two methods were no volitional contraction of abdominal muscles in hook-lying position with 45 degree hip flexion (method 1) and 90 degrees hip and knee flexion with feet off floor for inducing abdominal muscle contraction (method 2). Surface EMG activities were recorded from five muscles (sternocleidmastoid, anterior scaleneus, recuts abdominis, external oblique, internal oblique). And distance of rib cage elevation and angle of craniocervical flexion were measured using a three dimensional motion analysis system. The EMG activity of each muscle was normalized to the value of reference voluntary contraction (%RVC). The EMG activities, distance of rib cage elevation. and angle of craniocervical were compared using a paired t-test between two methods. The results showed that the EMG activities of sternocleidmastoid and anterior scaleneus during deep cervical flexion exercise in method 2 were significantly decreased compared to method 1 (p<.05). Distance of rib cage elevation and angle of craniocervical flexion were significantly decreased in method 2 (p<.05). The findings of this study indicated that deep cervical flexion exercise with contraction of abdominal muscles could be an effective method to prevent substitute motion for rib cage elevation and contraction of superficial neck flexor muscles.

• Journal of Nutrition and Health
• /
• v.29 no.6
• /
• pp.651-660
• /
• 1996

The purpose of this study was to examine and analyze the degrees and the influence factors of job satisfaction of dietitians working in hospitals in relation to performance of duty in their works and to provide effective management of hospital dietitians for high quality health and food service in hospital. The questionaire was prepared with reference to the previous studies on job satisfaction of dietitians working in hospitals throughout the nation. 201 dietitians in the country were surveyed. The period of research was from January 20 to February 28, 1995. The results are as follows. 1) In regard to the degree of job satisfaction of hospital dietitians, they showed the highest degree of job satisfaction in the relationships with fellow dietitians followed by worth and self-confidence, aptitude and interests, relationships with cooks, job stability, degree of recognition of the dietitians competence, supervision of the superiors, degree of application of professional knowledge, work load, wage level, degree of recognition of the importance of duty, cooperative relationships with load, wage level, degree of recognition of the importance of duty, cooperative relationships with doctors, degree of performance of clinical work, the number of dietitians, the prromotion system, and welfare system in that order. On the other hand, they showed the highest dissatisfaction with food service facilities. 2) The influence factors on job satisfaction are as follows. (1) Wage factor : Shorter weekday working hours and higher bonuses make greaster job satisfaction (R2=0.3115). (2) Working condition factor : Larger number of monthly holidays(R2=0.5142), shorter weekday working hours(R2=0.1077), longer previous food service experience and computer utilization (R2=0.1432) make greater job satisfaction. (3) Welfare factor : Welfare system (R2=0.4132) and promotion system (R2=0.1624) have to do with computer utilization. Job stability has to do with marital status and computer utilization (R2=0.1165). consequently, those married dietitians who use computers show higher job satisfaction. (4) Human relationship factor : Smaller mumber of patients receiving food makes greater job satisfaction (R2=0.1334). (5) Superivision factor : Shorter weekday working hours and larger number of monthly holidays make greater job satisfaction (R2=0.1709). (6) Achievement factor : Marriage, larger number of dietitians(R2=9.2293), age, larger number of monthly holiday, higher monthly wages and computer utiliazation (R2=0.1088) make greater job satisfaction. (7) Speciality factor : Marriage, longer current hospital tenure, higher position and working in seoul(R2=0.1142) make higher job satisfaction. (8) Job inclination factor : working in general hospitals rather than in oriental hispitals, working in seoul(R2=0.1776) and better bonuses(R2=0.1078)make greater job satisfaction. As a result, the following is suggested for the job satisfaction of hospital dietitions on the basis of this study : hospital dietitians can achieve miximum job satisfaction through smooth relationships with coworkers, and the responsible managers should improve welfare and working conditions for the job satisfaction of hospital dietitians.

• Journal of the Korea Convergence Society
• /
• v.8 no.11
• /
• pp.49-56
• /
• 2017

Curling sweeping is one of important motion to control the position of the curling stone, and sweeping speed and applied force to the broom pad are major research subjects. In this study, a device was developed to measure the force applied to the curling broom pad in curling sweeping motion, and two load cells were mounted between the broom pad and pad holder. Analog signals generated from the load cells were sampled about 300 times per second using a micro controller, and then converted to 10-bit digital signals. Calibration of the load cell and set up of regression equations to convert the measured electrical signals into mass (force) was done by three M1 class weights, and the developed system was designed as wearable device to minimize increasing of total weight of the broom. Same force was applied to the developed system and a force plate that was using as a reference force measurement system in field of sports, and the difference between the measured values were showed about $0.909{\pm}1.375N$(mean and standard deviation). The developed system could be applied other kinds of study which required force measurement function similar to sweeping motion.

• Journal of Aerospace System Engineering
• /
• v.14 no.3
• /
• pp.42-50
• /
• 2020

For calibration of the non-uniformity characteristics of the space-borne infrared (IR) sensor, a black body system shall provide estimated representative surface temperature at various reference temperatures by using the limited number of temperature sensors. The black body system proposed in this study has an I/F flange integrated on the rear side of the black body for installation of the heat pipe to transfer the residual heat after the black body heat-up. This design allows for obtaining a circular symmetric thermal contour of black body with low surface temperature gradient, leading to much easier representative temperature estimation. Additionally, this provides mechanically stable thermal I/F under launch and on-orbit environmental loads, as well as allowing a fail safe design by using the two heat pipes. Also, a highly accurate temperature estimation is possible even if the temperature sensors are attached on the surface on the rear side of the black body. The effectiveness of the thermal design of the proposed black body has been verified through the on-orbit thermal analysis. Based on the results, the representative surface temperature was estimated according to the number and position of the temperature sensors.

• Korean Journal of Poultry Science
• /
• v.6 no.2
• /
• pp.91-102
• /
• 1979

The basic problem of the broiler industry is that of fluctuating prices, mainly thanks to unstable supply of and inelastic demand for products as usually indicated as a peculiarity of agricultural commodities. This particularly brings the producer to a great economic risk, because he has to sell products under the condition of pure competition, whereas others from whom he has to buy deal under the condition of oligopoly or even monopoly. Therefore, producers economic position is generally placed in the worst comparing others dealing with, which results in unbalanced economic status of elements involved in broiler operation and further obstruction of industry development as a whole. A certain type of business coordination to overcome such a problem should be measured in order to improve the efficiency of entire operation and thus assure the balanced industry development. The concept of the economic integration developed in modern business system had been adapted to U.S. poultry industry which became common later around the world as a means of stabilizing producers price and whole industry as well. There are two main typos of integration; horizontal and vertical The former refers to the general grouping of similar business units, eg. a hatchery tying with other hatchery, while the latter refers to the knitting together of two or more stages of economic activities, eg. tying together among units of hatching, fled milling, production, processing and marketing. By having the industry integrated, risk and uncertainty involved in various stages of operation could be diversified. The typo of integrating contract between producers and integrators include the share of profits, flat fee payment, feed conversion payment and salary basis. In the U.S., extensive changes in production, processing, and marketing during the last few decades have changed the thicken broiler industry from one of small, widely scattered farms to one that is largo, concentrated and efficient. More than 99 percent of all broilers produced are grown under contract and by integrated firms which vary in size of operation and complexity. About 84 percent of all production is concentrated in 10 States. Some of the other factors ;hat contributed to these choses arc costs, energy use, prices, processing, marketing and demand. No integrated broiler production system has yet been applied in Korea's poultry industry, thus all stages all broiler operation run independently seeking for its own profit. Consequently, producers price fluctuate very widely around the year even more than 50 percent in a few months. This also leads to disadvantages of material supplies, processors and distributors and enforce the industry unstable. The current economic environment in Korea seems that the time for broiler integration comes and as an ideal integrator, feed millers, food processors and producers group may be considered.

• Korean Journal of Remote Sensing
• /
• v.32 no.4
• /
• pp.365-382
• /
• 2016

The results from the Global Positioning System (GPS) measurements of the Mobile Observation Vehicle (MOVE) on the eastern coast of Korea have been compared with REFerence (REF) values from the fixed GPS sites to assess the performance of Precipitable Water Vapor (PWV) retrievals in a kinematic environment. MOVE-PWV retrievals had comparatively similar trends and fairly good agreements with REF-PWV with a Root-Mean-Square Error (RMSE) of 7.4 mm and $R^2$ of 0.61, indicating statistical significance with a p-value of 0.01. PWV retrievals from the June cases showed better agreement than those of the other month cases, with a mean bias of 2.1 mm and RMSE of 3.8 mm. We further investigated the relationships of the determinant factors of GPS signals with the PWV retrievals for detailed error analysis. As a result, both MultiPath (MP) errors of L1 and L2 pseudo-range had the best indices for the June cases, 0.75-0.99 m. We also found that both Position Dilution Of Precision (PDOP) and Signal to Noise Ratio (SNR) values in the June cases were better than those in other cases. That is, the analytical results of the key factors such as MP errors, PDOP, and SNR that can affect GPS signals should be considered for obtaining more stable performance. The data of MOVE can be used to provide water vapor information with high spatial and temporal resolutions in the case of dramatic changes of severe weather such as those frequently occurring in the Korean Peninsula.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.102-109
• /
• 2019

This paper describes the design of the circuit card assembly to eliminate the communication error on a servo control unit installed in the automated resupply vehicle K56. K56 is a weapon system that automates the supply and loading of ammunition on the K-55A1 self-propelled artillery. As the core item responsible for ammunition movement control, the servo control unit is required to have good communication stability and reliability, but the conventional unit has recognized a problem that communication error intermittently occurs, resulting in an emergency stop phenomenon. We analyzed the communication signal of the servo control unit and identified the failure cause of the circuit card assembly to solve this problem. In addition, the signal interference in data/address line of the circuit card assembly was confirmed through analysis of the failure cause, and redesigned to avoid the interference, such as adjustment of the distance between communication lines and position change. Finally, the proposed cause analysis and redesign were verified through the component of servo control unit and attachment test on K56. We expected these study results to be used as reference for the design of other similar items.

• Analytical Science and Technology
• /
• v.16 no.5
• /
• pp.391-398
• /
• 2003

Basic research for the determination of boron content in biological sample has been carried out using the PGAA facility of the 24MW research reactor(HANARO). For investigation of characteristics for the measurement condition, neutron flux and its homogeneity were measured at irradiating geometry. The size of thermal neutron beam collimated from beam guide is $2{\times}2cm^2$ at the sample position. The neutron flux measured was the range of $1.0{\sim}6.5{\times}10^7n{\cdot}cm^{-2}{\cdot}s^{-1}$, and flux distribution from center within the radius of 4.5 mm and 9.0 mm was $5.77{\pm}0.71{\times}10^7n{\cdot}cm^{-2}{\cdot}s^{-1}$ and $4.68{\pm}1.64{\times}10^7n{\cdot}cm^{-2}{\cdot}s^{-1}$, respectively. Accordingly, sample size is adjusted within 10 mm for a homogeneous irradiation of high quality. Measurement system is designed to reduce the background source by Compton scattering and to improve the analytical sensitivity. To investigate the energy calibration and Compton suppression effect of gamma-ray counting system, the background conditions on both of Compton and single-mode were measured using NaCl standard. On the other hand, degree of spectral interference for sodium 472 keV peak as a matrix effect in the sample is established for an accurate boron analysis, and then boron content in three certified reference materials (NIST SRM 1570a, 1547, 1573a) was measured by using two modes and the results were compared with each other.