• Journal of Korean Society for Atmospheric Environment
• /
• v.28 no.1
• /
• pp.94-104
• /
• 2012

The purpose of this research is to quantify the compliance of on-road emission from a light duty diesel vehicle, based on a comparison to emission regulation standard. $NO_x$, CO and THC emissions were measured using a portable device on a selected real-world driving route with a length of approximately 22 km. On-road measurements were repeated by 10 times on a same route to reflect variability in traffic conditions. A test route was divided into 22 road links with length of 1 km to analyze emission results with higher spatial resolution. The average emissions of $NO_x$, CO and THC over total travel distance, which is approximately 220 km, were quantified to be in compliance with emission regulation standards. Under higher spatial resolution, $NO_x$ concentration exceeded a standard in 92 links out of 220 links. The extended time in stop period and the stop-and-go driving cycle were identified as two important reasons for increased $NO_x$ emissions in observed cases. Heavy traffics showed higher $NO_x$ emissions than free flow. These results indicate that the real-world vehicle emissions might exceed the compliance level associate with traffic conditions. Another interesting observation of this research is that the on-road emission characteristics can be independent to the average speed of road links with higher spatial resolution. Variability in on-road emission might not be fully described by solely relying on an average speed, because variability in traffic conditions and road conditions can influence on real-world vehicle emissions.

• Journal of Korean Society for Atmospheric Environment
• /
• v.34 no.2
• /
• pp.191-206
• /
• 2018

In this study, the HAPs(Harzard Air Pollutants) emission factor level of Starex and Grand Carnival was tested using PEMS (Portable Emissions Measurement System) on real road driving. As a result of RDE (Real Driving Emission test), the overall vehicle speed pattern showed similar characteristics. The real-road driving test at constant speed revealed emission factor is inversely proportional relationship to constant speed. Results of accelerating with speed limit on the real-road were shown as followings; Uran (less than 45 km/h)>Rural (<45 km/h, less than 80 km/h)>Motorway (>80 km/h). Moreover, the sudden acceleration and deceleration in driving at high speed was the increasing factor to the HAPs emission factor. This tendency is considered to be influenced by the operating environment on real roads.

• Journal of Korean Society for Atmospheric Environment
• /
• v.28 no.5
• /
• pp.506-517
• /
• 2012

Electronic Toll Collection System (ETCS), so called "Hi-Pass" in Korea, has improved traffic flow at toll gate of highways. It is known that the improvement of traffic flow should reduce air pollutants and $CO_2$ from vehicles. In this study, real driving emission of a light duty truck with Portable Emission Measurement System(PEMS) has been measured to evaluate the emission reduction effect due to ETCS. The correlations between driving variables and emissions have been analyzed to verify its effect on traffic flow improvement and emission reduction at toll gate. We considered average vehicle speed, Relative Positive Acceleration (RPA), and the distance of queue as driving variables. Compared to passing Manual Toll Collection System (MTCS) lane without queue, ETCS was able to reduce 38.7% of $NO_x$, 21.6% of soot, and 27.7% of $CO_2$. The results showed that the higher the average vehicle speed, the lower RPA and no queue in ETCS contributed to the emission reductions. Linear equation models with RPA and queue have been established by the multiple linear regression method. The linear models resulted in the higher coefficient of determination than those with only average vehicle speed used for establishing vehicle emission factors.

• Journal of Practical Engineering Education
• /
• v.6 no.2
• /
• pp.127-134
• /
• 2014

Analyzing test data of a vehicle for evaluating its emission performance is an essential process in automotive development field, yet it is intricate and tedious task. In addition, clear understanding and care are required when the analysis process is carried out. Computer software solutions significantly reduce the time and the effort for such analysis. Developing a computer routine to analyze the emission data in a vehicle test demands a complete understanding of the emissions analysis and its related details. In this paper, the principals to develop a LabVIEW analysis routine (VI) are introduced helping automotive engineers comprehend the emission analysis process of a vehicle test data and instruct them to develop similar routines for such analysis.

• Journal of Drive and Control
• /
• v.20 no.3
• /
• pp.15-24
• /
• 2023

The aim of this study was to measure and evaluate the exhaust emission factors of agricultural tractors. Engine characteristics and three exhaust emissions (CO, NO_x, PM) were collected under actual agricultural operating conditions. Experiments were performed on idling, driving, plow tillage, and rotary tillage. The load factor (LF) was calculated using the collected engine data, and the emission factor was analyzed using the LF and exhaust emissions. The engine characteristics and exhaust emissions were significantly different for each working condition, and in particular, the LF was significantly different from the currently applied 0.48 LF. The data distribution of exhaust emissions was different depending on the engine speed. In some conditions, the emission factor was higher than the exhaust emission standards. However, since most emission limit standards are values calculated using an engine dynamometer, even if the emission factor measured under actual working conditions is higher, it cannot be regarded as wrong. It is expected that the results of this study can be used for the inventory construction of a calculation for domestic agricultural machinery emissions in the future.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.3
• /
• pp.90-101
• /
• 2009

An objective of this study is to suggest a procedure to evaluate vehicle emissions regardless of the driving pattern. Field experiments using portable emission measurement system were conducted under the real world driving cycle. Standardized average for NOx, $CO_2$ emission and fuel consumption rates were calculated while the vehicle specific power distribution within each vehicle speed bin was taken into consideration. Composite emission factor and fuel economy, which were obtained based on the standardized average results and traffic statistics, showed good similarity to those acquired through the conventional chassis dynamometer tests qualitatively as well as quantitatively. Considering that a conventional method obviously has a limitation to reflect various characteristics of the real world, the new approach suggested in this study can be used as an alternative procedure to collect more specific data to establish the mobile emission factors.

• Journal of ILASS-Korea
• /
• v.23 no.3
• /
• pp.122-127
• /
• 2018

Recently, registrated passenger cars have increased and were close about seventy million at the end 2017 year in Korea. Among the passenger car using gasoline fuel make up forty six percentage of total registrated vehicles. In this study, investigation on real driving emission characteristics in the passenger car using gasoline fuel with various engine displacements were carried out. The real driving emission characteristics were measured and analyzed by using PEMS (Portable Emission Measurement System). PEMS was composed of gas analyzer, emission flow meter and sample conditioning system et al. Also, test six vehicles were selected to the gasoline passenger car with engine displacement from 1.6L to 3.7L. Two test routes with engine start of cold and hot conditions were applied to analyze the emission characteristics of RDE, respectively. The results show that the $CO_2$ emission have a increasing trend as the engine displacement and vehicle weight. Also, it is guessed that the $CO_2$ emission and vehicle weight were more correlated than the engine displacements. On the other hand, NOx emissions of RDE have not increasing or decreasing tendency according engine displacements or vehicle weight because the activation of three-way catalyst in the gasoline vehicles.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.1
• /
• pp.130-138
• /
• 2015

Despite of recently strengthened vehicle emission regulations, NOx emissions are not decreased in urban areas because of discrepancies between certification emission test modes and real driving conditions. Thus, researches on RDE-LDV (Real-driving Emission-Light-duty Vehicle) have been conducted actively using PEMS (Portable Emissions Measurement Systems). In the present study, NOx emissions were measured for 5 Korean light duty vehicles for real driving conditions including city, combined, highway, and up-downhill test route. Emission characteristics were analyzed for averaged NOx emissions per unit driving distance of each driving test routes. Furthermore, MAW (Moving Average Window) method based on $CO_2$ emissions from WLTC, which will be supported for EU regulations, was utilized. It was revealed that DRs (deviation ratios) for diesel vehicles (i.e., 5.1 ~ 8.4) were greater than gasoline vehicles (less than 0.15). Especially DR of diesel vehicle for up-downhill test route was 8.4, which indicates severe NOx emissions.

• Korean Journal of Agricultural Science
• /
• v.50 no.3
• /
• pp.383-394
• /
• 2023

In Korea, the U.S. Tier-4 Final emission standards have been applied to agricultural machinery since 2015. This study was conducted to analyze the emission characteristics of agricultural tractors during plow tillage operations using PEMS (portable emissions measurement systems). The tractor working speed was set as M2 (5.95 km/h) and M3 (7.60 km/h), which was the most used gear stage during plow tillage operation. An engine idling test was conducted before the plow tillage operation was conducted because the level of emissions differed depending on the temperature of the engine (cold and hot states). The estimated level of emissions for the regular area (660 m²), which was the typical area of cultivation, was based on an implement width of 2.15 m and distance from the work area of 2.2 m. As a result, average emission of CO (carbon monoxide), THC (total hydrocarbons), NOx (nitric oxides), and PM (particulate matter) were approximately 6.17×10-2, 3.36×10^-4, 2.01×10^-4, and 6.85×10^-6 g/s, respectively. Based on the regular area, the total emission of CO, THC, NOx, and PM was 2.62, 3.76×10^-2, 1.63, and 2.59×10^-4 g, respectively. The results of total emission during plow tillage were compared to Tier 4 emission regulation limits. Tier 4 emission regulation limits means maximum value of the emission per consumption power (g/kWh), calculated as ratio of the emission and consumption power. Therefore, the total emission was converted to the emission per power using the rated power of the tractor. The emission per power was found to be satisfied below Tier 4 emission regulation limits for each emission gas. It is necessary to measure data by applying various test modes in the future and utilize them to calculate emission because the emission depends on various variables such as measurement environment and test mode.

• Journal of ILASS-Korea
• /
• v.28 no.4
• /
• pp.184-190
• /
• 2023

The European Union has instituted a new emission standard protocol that necessitates real-time measurements from vehicles on actual roads. The adequate development of routes for real driving emissions (RDE) mandates substantial resources, encompassing both vehicles and a portable emission measurement system (PEMS). In this study, a simulation tool was utilized to predict the vehicle speed traversing the routes developed for the RDE measurements. Initially, the vehicle powertrain system was modeled for both a gasoline hybrid vehicle and a gasoline engine-only vehicle. Subsequently, the speed profile for the specified vehicle was constructed based on the RDE route developed for the EURO-6 standard. Finally, the predicted vehicle speed profiles for highway and urban routes were assessed utilizing the actual driving data. The driving model predicted more consistency in the vehicle speed at each driving section. Meanwhile, the human driver tended to accelerate further, and then decelerate in each section, instead of cruising at a predicted section speed.