• 한국생산제조학회지
• /
• 제22권4호
• /
• pp.635-642
• /
• 2013

We have prepared a DEMO conveyor device for conveying a large 8G class glass sheet using ahorizontal air-cushion system. This device consists of the body frame and the driving frame that are combined to realize a frame for conveying glass without any contact.The driving frame comprises an air flotation table (bed), drive roller supported at both ends, and ASU. Part of the ASU serves to control the airflow as the chamber consists of a porous pad and fan. Fiber filters replace the porous pad and axial fans serve as an air compressor. In addition, to determine the appropriate glass levitation from the air table, this study examined the design specifications of the applied filter (discharge speed of HEPA and ULPA filters, and flow rate) as well as the height of the and the proper supporting roller height (14mm). Then, after adjusting the position of the ASU and the number of ASUs required to configure the UNIT air floating C/V, we analyzed the height and flatness of the glass and derived the appropriate layout (1140-mm distance between ASUs).

• Journal of Pharmaceutical Investigation
• /
• 제27권1호
• /
• pp.39-49
• /
• 1997

Nicotinic acid was mixed with glass powders such as controlled pore glass (CPG), glyceryl controlled pore glass (GPG) and glass beads (GB) at room temperature. The physicochemical properties of nicotinic acid in the various mixtures were examined by differential thermal analysis, X-ray diffraction study. Infrared spectroscopy and BET gas adsorption measurements. The peak area at the melting point from the various mixtures of nicotinic acid and CPG was increased with an increase of nicotinic acid concentration while the broad peak area was remained unchanged in the DTA curve. As shown in the powder X-ray diffraction patterns, the crystalline peaks of nicotinic acid disappeared in mixture with CPG, suggesting the interaction of nicotinic acid and porous powders. It was found that the larger the content of CPG, the higher the ratio of an amorphous state to a crystalline state. BET isotherm showed that as the amount of nicotinic acid was increased, the specific surface area was reduced proportionally to nicotinic acid content of up to 40% and remained constant thereafter. Sublimation of nicotinic acid from the mixture of nicotinic acid and CPG was examined. A large quantity of nicotinic acid was retained in the mixture when stored on various temperatures in vacuo for 10 hours. The nicotinic acid mixtures with CPG or GPG showed a high dissolution rates of nicotinic acid in aqueous solution, especially in the initial dissolution stage. CPG is expected to be a good pharmaceutical excipient to reduce the crystallinity of drugs and to prevent sublimation of drugs.

• 한국세라믹학회지
• /
• 제32권4호
• /
• pp.507-515
• /
• 1995

The monolithic dry gels of the Li2O-Al2O3-TiO2-SiO2 system were prepared by the sol-gel technique using metal alkoxides as starting materials to obtain monolithic glass-ceramics at low temperature without melting. Activation energy for the crystal growth of the gel with 6.05% TiO2, nucleating ageng, for the preparation of Li2O-Al2O3-TiO2-SiO2 system glass-ceramic was 101.14kcal/mol. As a result of the analysis of DTA & XRD, it was confirmed that the crytallization of Li2O-Al2O3-TiO2-SiO2 system glass-ceramic was the most efficient when 6.05% TiO2, nucleating agent, was added. $\beta$-eucryptite solid solution crystals and $\beta$-spodumene solid solution crystals were detected in the sample heat treated above 85$0^{\circ}C$. The sintered gel heat treated at 85$0^{\circ}C$ had the specific surface area of 185$m^2$/g, the pore volume of 0.19cc/g and the average pore radius of 20.8$\AA$. This shows that the sintered gel is also comparatively porous material. In temperature range of 25~85$0^{\circ}C$ thermal expansion coefficient of the specimen which was crystallized for 10hrs at 85$0^{\circ}C$ was 6.7$\times$10-7/$^{\circ}C$, which indicated that the crystallized specimen was turned out to be the glass-ceramic with low thermal expansion.

• KIEAE Journal
• /
• 제1권2호
• /
• pp.47-54
• /
• 2001

Single sound absorbers such as porous materials, panels, and Helmholts resonators have limited performance with some extents of frequency region. For example, porous materials do not attenuate low frequency sounds, while panels do not absorb high frequency sounds. Composite absorption structure with coverings, porous materials, and air gaps are an alternative for wide band sound absorption. Slits, panels, perforated panels are those materials for coverings, glass wool, mineral wool, polyester, and polyurethane are frequently used porous materials. Air gap between the porous material and background surface is one of major factors which governs the absorption characteristics of composite absorption structures, especially in the low frequency area. Calculations and measurements show that the absorption coefficients of composite absorption structure, in mid and low frequency bands, are getting higher with increased air gaps. Perforated panels rather than slits and panels are good coverings with higher number as far as absorption coefficient is concerned. Perforated panels with porous materials and 37 cm of air gaps in background have high absorption coefficients for all frequency bands, above 0.7 to 1.0. All measurements are performed in reverberation chamber, Mokpo National University, according to ISO 354 and ISO 3382.

• 대한기계학회논문집
• /
• 제12권4호
• /
• pp.825-832
• /
• 1988

본 연구에서는 1차원 열흐름하에서 상부가 가열된 다공물질내의 열파이프 현 상과 관련하여 2상영역의 존재와 그 길이에 영향을 미치는 인자들을 실험적으로 관찰, 조사하였다.

• 한국세라믹학회지
• /
• 제46권5호
• /
• pp.488-492
• /
• 2009

Porous frit-bonded SiC ceramics were successfully prepared at a temperature as low as $800^{\circ}C$ from SiC, frit, and microbeads (glass or polymer). The effects of SiC starting particle size and microbead addition on microstructure, porosity, and flexural strength were investigated. The addition of hollow glass microbead improved the strength of frit-bonded SiC ceramics without the loss of porosity by acting additional binder phase between SiC grains. The 65 ${\mu}m$-sized SiC resulted in lower porosity and higher strength than 50 ${\mu}m$-sized SiC because of higher packing density. Typical flexural strengths of frit-bonded SiC were 23 MPa at 46% porosity and 19 MPa at 49% porosity.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.95-98
• /
• 2006

Filtration by fibrous filter is one of the Principle methods used for removing pollutant particles in the liquid. Because of the increasing need to protect both human health and valuable devices from exposure to fine particles, filtration has become more important. Filters have been developed with modified surface charge characteristics to capture and adsorb particles by electrokinetic interaction between the filter surface and particles contained in water. The main purposes of this study are to develop and evaluate the performance evaluation of the apparatus for making a positively charged porous filter media and to analyze the surface characteristics of the filter media for capturing negavitely charged contaminants mainly bacteria and virus from water. The experimental apparatus consists of a mixing tank, a vacuum pumping system, a injection nozzle, a roller press and a controller. The filter media is composed of glass fiber(50-750 nm), cellulose($10-20{\mu}m$) and colloidal charge modifier. The characteristics of filter media is analyzed by SEM(Scanning Electron Microscopy), AFM(Atomic Force Microscopy) and quantified by measuring the zeta potential values.

• Biotechnology and Bioprocess Engineering:BBE
• /
• 제5권6호
• /
• pp.436-440
• /
• 2000

Recently, we reported an improved technology for the degradation of organophosphate nerve agents using whole cells of genetically engineered Escherichia coli that anchored and displayed the enzyme organophosphorus hydrolase on the cell surface. In this paper we report the immobilization of these cells on highly porous sintered glass beads and the subsequent application of the immobilized cell in a continuous-flow packed bed bioreactor for the biodetoxification of a widely used insecticide, coumaphos.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.202-202
• /
• 2012

염료감응태양전지(DSSC)의 광변환 효율을 향상시키기 위하여 진공챔버에서 450도 고온에서 O2, Ar, and N2 혼합가스를 주입하여 다양한 plasma로 TiO2 박막을 처리하면서 소성시켰다. TiO2 표면을 cleaning하고 활성화함으로서 염료의 결합력을 향상시키는 것 외에 TiO2 내부의 oxygen vacancy를 변화를 관찰하였다. 실험에 사용한 박막은 glass 위에 FTO 박막을 입히고, 다공성 TiO2 나노입자 박막을 코팅하여 제조하였다(porous TiO2 나노입자(${\sim}12{\mu}m$)/FTO(Fluorine doped Tin oxide; $1{\mu}m$)/glass). 완성된 광전극에 대해서 XRD, XPS, EIS, FE-SEM 등을 이용하여 분석하였다. 또한 이렇게 전처리된 광전극을 사용한 DSSC를 제작하였다. 그리고 Solar-simulator를 통해 그 효율을 측정하여 '플라즈마환경에서 소성된 광전극에 대한 DSSC의 광변환효율에 미치는 효과'을 고찰하였다.

• 한국세라믹학회지
• /
• 제30권10호
• /
• pp.838-844
• /
• 1993

To control the pore size of silcia gel, formamide (FA), N,N-dimethyl formamide (DMF), polyethylene glycol (PEG) and polyacrylic acid (PAA) were added in the sol-gel process from starting solution with tetramethyl orthosilicate (TMOS). The gels were characterized using porosimeter, TG-DTA and SEM. As a result, the more contents of FA and PAA was increased the more gelation time was decreased, also the more contents of DMF and PEG was increased the more gelling time was increased. The mean pore size of gels was larger in the order of PAA, DMF, FA and PEG. And the mean pore size of porous silica glass was 59.0$\AA$, 31.5$\AA$, 29.9$\AA$ and 29.0$\AA$, respectively, heated at 75$0^{\circ}C$/100$0^{\circ}C$.