• Journal of Sensor Science and Technology
• /
• v.20 no.3
• /
• pp.168-171
• /
• 2011

Porous 3C-SiC(pSiC) samples with different pore diameters were prepared from poly crystalline N-type 3C-SiC by electrochemical anodization. The pSiC surface was chemically modified by the sputtering of Pd and Pt nano-particles as a hydrogen catalyst. Changes in resistance were monitored with hydrogen concentrations in the range of 110 ppm - 410 ppm. The variations of the electrical resistance in the presence of hydrogen demonstrated that Pd and Pt-deposited pSiC samples have the ability to detect hydrogen at room temperature. Regardless of the catalyst, the 25 nm pore diameter samples showed good response and recovery properties. However, the 60 nm samples showed unstable and slow response. It was found that the pore size affects the catalyst reaction and consequently, results in changes of the sensitivity to hydrogen.

• Korean Journal of Materials Research
• /
• v.26 no.6
• /
• pp.320-324
• /
• 2016

Porous SiC beads were prepared by freeze-drying a polycarbosilane (PCS) emulsion. The water-in-oil (w/o) emulsion, which was composed of water, PCS dissolved p-xylene, and sodium xylenesulfonate (SXS) as an emulsifier, was frozen by dropping it onto a liquid $N_2$ bath; this process resulted in 1~2 mm sized beads. Beads were cured at $200^{\circ}C$ for 1 h in air and heat-treated at $800^{\circ}C$ and $1400^{\circ}C$ for 1 h in an Ar gas flow. Two types of pores, lamella-shaped and spherical pores, were observed. Lamellar-shaped pores were found to develop during the freezing of the xylene solvent. Water droplets in the w/o emulsion were changed into spherical pores under freeze-drying. At $1400^{\circ}C$ of heat-treatment, porous SiC was synthesized with a low level of impurities.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.167-167
• /
• 2015

SiC thin films made by vapor silicon infiltration into porous graphite can be obtained for shorter time than liquid silicon. Si diffusion coefficient is estimated by comparing experiment results with quadratic equation obtained by Fick's second law.

• Journal of the Korean Ceramic Society
• /
• v.49 no.6
• /
• pp.625-630
• /
• 2012

Highly porous silicon carbide (SiC) ceramics were fabricated from polysiloxane, SiC and carbon black fillers, AlN-$Y_2O_3$ additives, and poly (ether-co-octene) (PEOc) and expandable microsphere templates. Powder mixtures with a fixed PEOc content (30 wt%) and varying SiC filler contents from 0-21 wt% were compression-molded. During the pyrolysis process, the polysiloxane was converted to SiOC, the PEOc generated a considerable degree of interconnected porosity, and the expandable microspheres generated fine cells. The polysiloxane-derived SiOC and carbon black reacted and synthesized nano-sized SiC with a carbothermal reduction during a heat-treatment. Subsequent sintering of the compacts in a nitrogen atmosphere produced highly porous SiC ceramics with porosities ranging from 78 % to 82 % and a flexura lstrength of up to ~7 MPa.

• Journal of the Korean Ceramic Society
• /
• v.34 no.5
• /
• pp.467-472
• /
• 1997

Porous silicon was prepared by an anodic etching. The pore size was about 10 nm at an etching time of 20 sec and a current density of 20 mA/$\textrm{cm}^2$. The porous layer was composed of an micro-porous layer (0.6 ${\mu}{\textrm}{m}$) and a macro-porous layer (10 ${\mu}{\textrm}{m}$). Room temperature PL with maximum peak 6700$\AA$ appeared. The peak disappeared by an oxidation reaction when the porous silicon was heated to 100~20$0^{\circ}C$ in atmosphere. In order to avoid the oxidation a heat treatment was done in H2 atmosphere. The micro-pore and Si column, which formed quantum well, were collapsed by the high temperature. The PL maximum peak of heated sample was gradually red-shifted and showed about 300$\AA$ red-shift at 50$0^{\circ}C$. The intensity of PL was maintained to high temperatures in lower pressures. The porous Si was carbonized in C2H2+H2 gas in order to increase thermal stability. The carbonization of the porous Si prevented red-shift of the maximum PL peak caused by sintering effect at high temperatures, and the carbonized porous Si showed Pl signal at higher temperatures by above 20$0^{\circ}C$ than the sample in H2 atmosphere.

• Journal of the Korean Ceramic Society
• /
• v.56 no.2
• /
• pp.191-196
• /
• 2019

This study assessed the feasibility of a Ti₃AlC₂ MAX phase as an Al-source for the formation of a mullite bond in the fabrication of porous SiC tubes with high strength. The as-received Ti₃AlC₂ was partially oxidized at 1200℃ for 30 min before using to minimize the abrupt volume expansion caused by oxidation during sintering. Thermal treatment at 1100-1400℃ for 3 h in air led to the formation of Al₂O₃ by the decomposition of Ti₃AlC₂, which reacted further with oxidation-derived SiO₂ on the SiC surface to form a mullite phase. The fabricated porous SiC tubes with a relative density of 48 - 62 % exhibited mechanical strengths of 80 - 200 MPa, which were much higher than those with the Al₂O₃ filler material. The high mechanical strength of the Ti₃AlC₂-added porous SiC was explained by the rigid mullite neck formation along with the retained Ti₃AlC₂ with good mechanical properties.

• The Korean Journal of Ceramics
• /
• v.1 no.3
• /
• pp.147-151
• /
• 1995

Porous composite of $Al_2O_3$ and AIN based mullite and SiC can be prepared by alumium reaction synthesis and atmosphere controllied sintering in order to improve the durability of a gas filter body. The porous $Al_2O_3$-AIN-mullite, which has a strength of 168 kg/$\textrm{cm}^2$ and porosity of 51.59%, could be obtained by stmospheric firing at $1600^{\circ}C$ and the porous $Al_2O_3$-AIN-SiC with a porosity of 33% and strength of 977 kg/$\textrm{cm}^2$, could also be prepared. The average pore size has been changed from 0.2$\mu\textrm{m}$ in a reduction atmosphere and to 2$\mu\textrm{m}$ in an air atmosphere, respectively.

• Journal of the Korean Ceramic Society
• /
• v.55 no.3
• /
• pp.285-289
• /
• 2018

We synthesized silicon carbide (${\beta}-SiC$) nanowires with nano-scale diameter (30 - 400 nm) and micro-scale length ($50-200{\mu}m$) on a porous body using low-grade silica and carbon black powder by carbothermal reduction at $1300-1600^{\circ}C$. The SiC nanowires were formed by vapor-liquid-solid deposition with self-evaporated Fe catalysts in low-grade silica. We investigated the characteristics of the SiC nanowires, which were grown on a porous body with Ar flowing in a vacuum furnace. Their structural, optical, and electrical properties were analyzed with X-ray diffraction (XRD), transmission electron microscopy (TEM), and selective area electron diffraction (SAED). We obtained high-quality SiC single crystalline nanowire without stacking faults that may have uses in industrial applications.

• Journal of the Korean Ceramic Society
• /
• v.46 no.5
• /
• pp.520-524
• /
• 2009

Porous self-bonded silicon carbide (SBSC) ceramics were fabricated at temperatures ranging from 1750 to $1850^{\circ}C$ using SiC, Si, C as starting materials and Al as an optional sintering additive. The effect of Al addition on the porosity and strength of the porous SBSC ceramics were investigated as functions of sintering temperature and Si:C ratio. The porosity increased with decreasing the Si:C ratio and increasing the sintering temperature. It was possible to fabricate SBSC ceramics with porosities ranging from 37% to 44% by adjusting the Si:C ratio and the sintering temperature. Addition of Al additive promoted densification and necking between SiC grains, resulting in improved strength. Typical flexural strengths of SBSC ceramics with and without Al addition were 44 MPa and 34MPa, respectively.

• Journal of the Korean Ceramic Society
• /
• v.46 no.5
• /
• pp.488-492
• /
• 2009

Porous frit-bonded SiC ceramics were successfully prepared at a temperature as low as $800^{\circ}C$ from SiC, frit, and microbeads (glass or polymer). The effects of SiC starting particle size and microbead addition on microstructure, porosity, and flexural strength were investigated. The addition of hollow glass microbead improved the strength of frit-bonded SiC ceramics without the loss of porosity by acting additional binder phase between SiC grains. The 65 ${\mu}m$-sized SiC resulted in lower porosity and higher strength than 50 ${\mu}m$-sized SiC because of higher packing density. Typical flexural strengths of frit-bonded SiC were 23 MPa at 46% porosity and 19 MPa at 49% porosity.