• 한국막학회:학술대회논문집
• /
• 한국막학회 1997년도 춘계 총회 및 학술발표회
• /
• pp.21-22
• /
• 1997

최근의 이온교환막은 종래의 양이온교환막의 표면에 polycation 등의 얇은 층을 덧붙인 다층막(multi-layer membrane)의 형태가 많이 이용되고 있으며, 정전기적 반발력의 차 등을 이용하여 원자가가 다른 이온들간의 투과성에 차를 부여하기 위하여 이용되고 있다. 이 때문에 polycation막을 통한 1가 이온과 2가 이온의 투과성을 연구하는 것은 우수한 이온교환막을 제작하는것 이상으로 중요하다. 본 연구에서는 고정전하농도(fixed charge density, $\Phi$ X)가 낮은 다공성 저전하음이온교환막을 제작하여, 양측에 대이온(counterion)은 같고 복이온(co-ion)이 다른 전해질용액을 두었을 경우에 관찰되는 막전위를 측정하였다. 이를 토대로 음이온교환막을 통한 막전위의 농도의존성에 관하여 검토하였으며, 비평형열역학(non-equilibrium thermodynamies)에 기초한 이론적 모델을 도입하여 실험치와 비교, 해석하였다.

• 한국막학회:학술대회논문집
• /
• 한국막학회 2003년도 The 4th Korea-Italy Workshop
• /
• pp.129-132
• /
• 2003

Silica/SUS composite membranes were prepared for CO removal from products of methanol steam reforming. A support was prepared by coating Ni powder of sub-micron and SiO$_2$ sols of particle size of 500nm and 150nm in turns on a porous stainless steel (SUS) substrate. Silica top layer was coated on the modified support using colloidal sol with nanoparticle. As a result of mixture gas permeation test of silica composite membrane using H$_2$(99%)/CO(1%), CO concentration of 10000 ppm was reduced to under 81 ppm, which is acceptable in PEMFC anode gas specification. Permeation mechanism through the membrane was mainly molecular sieving.

• 한국수소및신에너지학회논문집
• /
• 제25권4호
• /
• pp.419-424
• /
• 2014

Direct ethanol fuel cell has been fabricated with ceramic membrane. A porous silicon carbide (SiC) membrane having approximately 30% porosity has been applied for a direct ethanol proton exchange membrane (DE-PEM) fuel cell. A horizontal type cell having Pt ($18mg/cm^2$) catalyst layer on both side of the ceramic membrane was used for the demonstration test. The ethanol oxidation based-fuel cell stack showed very high voltage (1.289V) and measurable current level (68mA) even though at room temperature.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.873-876
• /
• 2006

At the green roof on the concrete structure, root penetration can be the most problem to water leakage. Root occur cracks due to penetrate to concrete which have porous organization by itself. Crack on the concrete structure would be constantly shrinks and expands, it occur to water leakage and decrease durability of concrete structure. Therefore, in this paper, the result of the root penetration test for waterproofing which protect concrete structure from the water leakage or other environment conditions would be apply to understand the reason of root penetration.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.312-313
• /
• 2006

The primary aim pursued by the preparation of separation membrane is the preparation of the membrane thin as well as with no defect. The field-flow fractionation deposition is a new molding technology which can overcome the traditional disadvantages such as multi-preparation to the preparation of great area of separation membrane with no defect. Therefor the mainly ingredients which influence the appearance and performance of titanium membrane layer are investigated by scanning electricity mirror (SEM) as well as porous material testing instrument: powder performance prepared and confected; selection of supporting body; sintering system such as temperature and time. It is shown that the membrane thickness can be controlled at $50{\mu}m$ or so; the filtration precision mainly rests with powder performance and selection of supporting body and little sintering system

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.372-372
• /
• 2007

Titanium oxide nanotube arrays were fabricated by the anodization of pure titanium thin film deposited at $500^{\circ}C$ on silicon substrates. The titania nanotubes were grown by anodization in nonaqueous-base electrolytes at different potentials between 5 V and 30 V. $TiO_2$ nanotube array with a small pore diameter of 40 nm and long titanium oxide layer of $4\;{\mu}m$ was obtained. The $TiO_2$ nanotube array was used as a porous electrode for quartz crystal microbalance (QCM). Nanoporous morphology of electrode will increase the sensitivity of microbalance.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.189.1-189.1
• /
• 2013

Titanium dioxide (TiO2) is a wide bandgap semiconductor possessing photochemical stability and thus widely used for photocatalysis. However, enhancing photocatalytic efficiency is still a challenging issue. In general, the efficiency is affected by physio-chemical properties such as crystalline phase, crystallinity, exposed crystal facets, crystallite size, porosity, and surface/bulk defects. Here we propose an alternative approach to enhance the efficiency by studying interfaces between thin TiO2 layers to be stacked; that is, the interfacial phenomena influencing on the formation of porous structures, controlling crystallite sizes and crystallinity. To do so, multi-layered TiO2 thin films were fabricated by using a sol-gel method. Specifically, a single TiO2 thin layer with a thickness range of 20~40 nm was deposited on a silicon wafer and annealed at $600^{\circ}C$. The processing step was repeated up to 6 times. The resulting structures were characterized by conventional electron microscopes, and followed by carrying out photocatalytic performances. The multi-layered TiO2 thin films with enhancing photocatalytic efficiency can be readily applied for bio- and gas sensing devices.

• 한국표면공학회지
• /
• 제32권1호
• /
• pp.21-30
• /
• 1999

Coating adherance behavior of low carbon steels, produced by POSCO, Korea, was studied in order to study the characteristics of hot rolled galvanized iron(HGI) manufactured without pickling line and the development of its process. Galvanizing experiments were carried out in zinc pot with 0.2wt% Al after hot rolled plates with scale were reduced at $550~750^{\circ}C$ in 10~30% hydrogen gas atmosphere during 60~400seconds. The reduced plates and coated products were examined by SST, XRD, SEM and EPMA on their surfaces and cross sections. Coating layer of HGI manufactured with pickling line was composed of retained scale, Fe-Zn-Al compound, Fe-Zn compound ($\delta_1\;and\;\zeta$ Phase) and pure zinc. It was superior to HGI in coating adhesion. It seems to be due to forming of Fe-Zn-Al compound in interface of matrix and retained porous scale.

• 한국표면공학회지
• /
• 제36권6호
• /
• pp.430-436
• /
• 2003

The nanoocrystalline Ni-l5W(at.%) coating electrodeposited on the high carbon steel was oxidized at 700 and $800^{\circ}C$ in air, and the resultant oxidation properties were investigated using XRD, EPMA, TGA and TEM. The oxidation resistance of the coating was not so good that most of the coating was oxidized after oxidation at $800^{\circ}C$ for 5 hrs. The oxidation led to the formation of the outer, thin NiO oxide scale and the inner, porous, rather thick ($NiWO_4$＋NiO) mixed layer containing a bit of $WO_2$. During oxidation, substrate elements such as Fe and Cr diffused outwardly toward the coating, according to the concentration gradient.

• Bulletin of the Korean Chemical Society
• /
• 제20권7호
• /
• pp.786-790
• /
• 1999

Relatively inert surface of microcrystalline MgO was modified into chemically active one by carrying out controlled hydration followed by dehydration at elevated temperature under dynamic vacuum. Even though the treatment by the first cycle of hydration-dehydration did not alter the porosity of MgO, it largely enhanced surface reactivity of the MgO toward adsorbed water, turning its outer layer into brucite upon rehydration. Treatment by the second cycle of hydration-dehydration generated micropores, and slit-shaped mesopores, raising the porosity of the MgO. The overlayer of Fe2O3 of the core/shell type composite magnesium oxide enhanced this surface modification, turning its surface into more porous and more active one than that of uncoated MgO, after the treatment by the hydration-dehydration.