In the dust separation by using porous filter media, the structure of dust layer deposited on the filter surface of filter medium directly affects the effective filtration. The present study has investigated the specific resistance (K$_2$') of the dust layer and its porosity ($\varepsilon$$_{c}$) for three different filters; FA composite filter, metal fiber filter and stainless filter. The specific resistance (K$_2$') increased and at the same time the cake porosity ($\varepsilon$$_{c}$) decreased with the increase of filtration velocity, possibly due to the compressible effect of dust layer. However, under the low dust concentration, subsequent dust particles would block the open channels through the layer resulting in high specific resistance of the layer. The FA composite filter among three filters was shown to be the most effective filter for dust cake filtration at low filtration velocities less than 0.1 m/s for an approximate dust concentration of 5 g/㎥.
구리분말 소결윅 히트파이프의 열수송 한계를 예측하는 이론적 해석을 수행하였다. 히트파이프의 직경은 8 mm이고 물을 작동유체로 사용하였다. 입자의 직경을 대표적인 5 가지로 분류하여 각각의 유효 모세관 반경($r_c$) 기공률($\varepsilon$), 투파율(K)을 토대로 작동온도와 윅 두에 그리고 경사각에 따른 모세관압력과 열수송 한계, 열저항을 분석하였다. 소결윅의 모세관한계는 입자 직경이 크고 윅 두께가 증가하며 작동온도가 높을수록 증가했다 기공률과 모세관 반경이 증가할수록 열수송 한계가 높아졌으며, 윅 두께가 증가함에 따라 열저항이 크게 상승하였다.
Low carbon steel (S20C steel) and SPCC steel sheet have been austenitic nitrided at $700^{\circ}C$ in a closed pit type furnace by changing the flow rate of ammonia gas and heat treating time. When the flow rate of ammonia gas was low, the concentration of residual ammonia appeared low and the hardness value of transformed surface layer was high. The depth of the surface layer, however, was shallow. With increasing the concentration of residual ammonia by raising up the ammonia gas flow, both the depth of the surface layer and the pore depth increased, while the maximum hardness of the surface layer decreased. By introducing a large amount of ammonia gas in a short time, a deep surface layer with minimal pores on the outermost surface was obtained. In this experiment, while maintaining 10~12% of residual ammonia, the flow rate of inlet ammonia gas, 7 liter/min, was introduced at $700^{\circ}C$ for 1 hour. In this condition, the thickness of the surface layer without pores appeared about $60{\mu}m$ in S20C steel and $30{\mu}m$ in SPCC steel plate. Injecting additional methane gas (carburizing gas) to this condition played a deteriorating effect due to promoting the formation of vertical pores in the surface layer. For $1^{st}$ transformed surface layer for S20C steel, maintaining 10~12% residual ammonia condition via austenitic nitriding process resulted in ${\varepsilon}$ phase with relatively high nitrogen concentration (just below 4.23 wt.%N) among the mixed phases of ${\varepsilon}+{\gamma}$. The ${\varepsilon}$ phase was formed a specific orientation perpendicular to the surface. For $2^{nd}$ transformed layer for S20C steel, ${\gamma}$ phase was rather dominant (just above 2.63 wt.%N). For SPCC steel sheet, there appeared three phases, ${\gamma}$, ${\alpha}(M)$ and weak ${\varepsilon}$ phase. The nitrogen concentration would be approximately 2.6 wt.% in these phases condition.
스크린 메쉬윅 및 소결윅 히트파이프의 열수송 한계를 예측하기 위한 이론적 해석을 수행하였다. 히트파이프의 직경은 8mm이고 작동유체는 물을 사용하였다 250메쉬 조건에서, 각각의 유효 모세관 반경(r$_{c}$ ), 기공률($\varepsilon$), 투과율(K)을 토대로 작동온도와 윅 두께 그러고 경사각에 따른 모세관압력과 열 수송 한계, 열 저항을 분석하였다. 작동온도가 높고 윅 두께가 증가할수록 모세관한계가 높아졌으며, 대체로 소결윅이 스크린적보다 높은 열수송 한계를 나타냈다. 스크린윅의 열저항이 소결윅보다 높았으며, 두 가지 모두 윅 두께가 증가함에 따라 열저항이 선형적으로 상승하였다.
International Journal of Concrete Structures and Materials
/
제9권1호
/
pp.1-20
/
2015
This work is devoted to the study of fresh and hardened properties of concrete containing recycled gravel. Four formulations were studied, the concrete of reference and three concretes containing recycled gravel with 30, 65 and 100 % replacement ratios. All materials were formulated on the basis of S4 class of flowability and a target C35 class of compressive strength according to the standard EN 206-1. The paper first presents the mix design method which was based on the optimization of cementitious paste and granular skeleton, then discusses experimental results. The results show that the elastic modulus and the tensile strength decrease while the peak strain in compression increases. Correlation with the water porosity is also established. The validity of analytical expressions proposed by Eurocode 2 is also discussed. The obtained results, together with results from the literature, show that these relationships do not predict adequately the mechanical properties as well as the stress-strain curve of tested materials. New expressions were established to predict the elastic modulus and the peak strain from the compressive strength of natural concrete. It was found that the proposed relationship E-$f_c$ is applicable for any type of concrete while the effect of substitution has to be introduced into the stress-strain (${\varepsilon}_{c1}-f_c$) relationship for recycled aggregate concrete. For the full stress-strain curve, the model of Carreira and Chu seems more adequate.
생체재생용 지지체는 높은 다공구조와 적당한 기계적인 강도를 필요로 한다. 높은 다중성과 적당한 다공크기는 지지체와 주변 환경 사이에 영양분의 공급을 원활하게 하여 셀의 지지체에 대한 초기 집착력과 성장을 가능하게 하는 구조를 제공한다. 본 논문에서는 polycaprolactone(PCL) 나노섬유를 화학 발포제와 전기방사공정을 이용하여 다양한 조건하에서 제조하였다. PCL 용액의 농도가 8wt%, 발포제의 함량 0.5wt%, 발포온도 $100^{\circ}C$ 및 체류시간 2-3초에서 가공성 측면과 다공성 측면에서 우수한 발포된 나노섬유를 얻을 수 있었다. 또한 세포의 성장성을 측정하기 위하여 인체피부세포를 셀 켤츄어링하여, 발포되지 않은 나노섬유와 비교하였다.
The defects of partial denture frameworks are mainly shrinkage porosity, inclusions, micro-crack, particles from investment, and dendritic structure. In order to investigate a good casting condition of partial denture frameworks, the three casting alloys and casting methods were used and detected casting defects were analyzed by using electrochemical methods. Three casting alloys (63Co-27Cr-5.5Mo, 63Ni-16Cr, 63Co-30Cr-5Mo) were prepared for fabricating partial denture frameworks with various casting methods; centrifugal casting (Kerr, USA), high frequency induction casting (Jelenko Eagle, USA), vacuum pressure casting (Bego, Germany). The casting temperature was $1,380^{\circ}C$ (63Co-27Cr-5.5Mo and 63Ni-16Cr) and $1,420^{\circ}C$ (63Co-30Cr-5Mo). The casting morphologies were analyzed using FE-SEM and EDX. The corrosion test of the dendritic structure was performed through potentiodynamic method in 0.9% NaCl solutions at $36.5^{\circ}C$ and corrosion surface was observed using SEM. The defects of partial denture frameworks improved in the order of centrifugal casting, high frequency induction casting, and vacuum pressure casting method, especially, pore defects were found at part of clasp in the case of centrifugal casting method. The structure of casting showed dendritic structure for three casting alloys. In the 63Co-27Cr-5.5Mo and 63Co-30Cr-5Mo, $\alpha$-Co and $\varepsilon$-Co phases were identified at matrix and $${\gamma}$-Ni_2$Cr second phase were shown in 63Ni-16Cr. Also, the corrosion resistance of cast structure increased in the order of vacuum pressure casting, high frequency induction casting, and centrifugal casting method.
포천 지역에 분포하는 쥬라기 화강암을 대상으로 미세균열 분포특성이 화강암의 역학적 성질에 미치는 영향에 대하여 연구하였다. 3종의 방향성 시편을 대상으로 일축압축시험이 실시되었으며, 각 시편은R(riftplane), G(grain plane) 및 H(hardway plane) 축에 각각 직각이다. 다양한 탄성 상수 중, 3 방향에 따른 포아송비의 변화가 검토되었다 파괴 강도 비-포아송비의 관계도에서 포아송비의 범위는 H-시편에서 가장 높은 분포양상을 보이며 G-시편, R-시편의 순으로 감소한다. 분포곡선은 $I\simIII$ 단계에서는 거의 선형이며, IV-3 단계에서는 기울기의 급격한 증가를 보인다. 관계도에서 보는바와 같이 파괴강도비 $0.92\sim0.96$에서 변곡점이 형성된다. IV-3단계는 탄성 영역의 밖에 속한다. 4단계의 파괴단계에서의 거동은 응력-체적변형율 곡선에서 분석되었다 암석의 거동을 지배하는 응력증분-체적변형율 방정식에서 특징적인 재료상수인 a, n, Q, m 및 $\varepsilon_v^{mcf}$가 결정되었다. 이들 상수중에서 미세균열의 폐합영역( I 단계)에서 고유의 미세균열의 공극률$(a, 10^{-3})$ 그리고 압축지수(n)는 각각 $a^R(3.82)>a^G(3.38)>a^H(2.32)$ 그리고 $n^R(3.69)>n^G(2.79)>n^H(1.99)4의 순서로 나타난다. 특히 IV 단계의 미세균열의 임계체적변형율($\varepsilon_v^{mcf}$)은 3번 면에 수직인 H-시편에서 가장높게 나타난다. 이러한 결과에서 포아송비 및 재료상수와 같은 역학적 성질은 2 조의 미세균열과 밀접한 관계를 보이고있다. 강도 이방성과 미세균열의 방향성과의 상관성은 암석의 파괴 연구에 주요하게 적용될 수 있다.
세공분포가 서로 다른 두 종류(KHT, X-5)의 ${\gamma}$-알루미나 pellet에 아황산가스를 흡착 제거시킬 경우 반응이 진행되면서 각각의 세공벽에 반응생성층이 형성되어 반응속도 상수($K_v$), 세공률(${\varepsilon}_p$), 유효내부 확산계수($D_e$)의 변화와 세공반경이 줄어들어 세공막힘 현상이 일어나게 된다. 이들 영향을 고려하여 세공분포를 이용한 Random pore model로 최적반응온도 $450^{\circ}C$에서 산화구리의 각 담지농도(4, 6, 8, l0 wt%)와 아황산가스의 농도(1000, 2000ppm)에 대한 전환율을 수학적 모델로부터 계산하였다. 산화구리의 담지농도가 증가할수록 세공내의 유효반응 표면적과 세공률의 감소, 내부확산저항의 증가, 미세세공의 세공막힘 현상으로 전환율은 감소하였다. 총괄 전환율은 ${\gamma}$-알루미나 pallet의 표면 국부 전환율에 크게 의존하였으며 산화구리의 담지농도가 낮고 아황산가스의 농도가 클수록 증가하였다. 반응기에 유입되는 아황산가스의 유속은 반응초기 CuO의 전환율에 영향을 주었고 세공분포가 발달하여 세공율이 큰 ${\gamma}$-알루미나 pellet일수록 전환율은 높게 나타났다.
처분 안전성 평가를 위해서는 지하매질을 통한 방사성핵종의 이동특성 규명과 신뢰성 있는 지하 핵종이동 모델의 확보가 무엇보다 중요하다. 본 연구에서는 지하핵종이동 모델 개발을 위한 기초연구로서 충전층 실험을 수행하고, 실험결과를 제안된 핵종이동모델과 비교ㆍ검토하였다. 실험에서는 분쇄응회암으로 충전된 칼럼에서의 핵종이동 현상을 규명하고, 모델 시뮬레이션을 통해서는 세공확산을 모델에 고려하여 핵종이동에서 세공확산의 역할을 검토하였다. 충전층 실험에서 수력학적 분산계수는 비흡착성의 iodine을 사용하여 측정하였으며, 이 때 측정한 분산계수는 공극율 $\varepsilon$=0.483, 평균유속 (equation omitted)=0.915$\times$$10^{-2}$ cm/min에서 D$_{L}$=0.11$\times$$10^{-2}$$\textrm{cm}^2$/min이었다. 그리고 중ㆍ저준위 방사성폐기물의 대표 핵종으로 사용한 Cs-137은 응회암에 대해 높은 지연특성을 보였으며, 파과곡선은 비대칭 형태로서 단말현상이 길게 나타났다. 모델 시뮬레이션 결과, 매질 세공내 확산과정은 다공성의 지하매질을 통한 핵종이동에서 중요한 율속단계 역할을 하였다.다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.