• Journal of the Korean Ceramic Society
• /
• v.45 no.11
• /
• pp.675-680
• /
• 2008

The effect of pore former content on both porosity and pore structure was investigated for porous sintered reaction-bonded silicon nitrides (SRBSNs). A spherical PMMA with $d_{50}=8{\mu}m$ was employed as a pore-former. Its amount ranged from 0 to 30 part. Porous SRBSNs were fabricated by post-sintering at various temperatures where the porosity was controlled at $12{\sim}52%$. The strong tendency of increasing porosity with PMMA content and decreasing porosity with sintering temperature was observed. Measured pore-channel diameter increased $(0.3{\rightarrow}1.1{\mu}m)$ with both PMMA content and sintering temperature.

• Journal of Environmental Science International
• /
• v.24 no.11
• /
• pp.1463-1471
• /
• 2015

The surface modified activated carbons (SMACs) were prepared with various $P_2O_5$ concentrations using two activated carbons (ACs: waste citrus peel-based activated carbon and coconut-based activated carbon). The characteristics and adsorptivity of bisphenol A (one of phenolic endocrine disrupting chemicals) were compared between ACs and SMACs. The contents of C, H and N of SMACs were similar to those of ACs, but the content of $P_2O_5$ for the former increased greatly than for the latter, due to the impregnation of $P_2O_5$ into the pores. The specific surface area, total pore volume, average pore diameter and iodine adsorptivity for the former decreased due to the impregnation of $P_2O_5$ into the pores, compared to those for the latter. The adsorptivity of bisphenol A for the former were higher than that for the latter, although specific surface area, total pore volume, average pore diameter and iodine adsorptivity for the former were lower than those for the latter.

• Journal of the Korean Ceramic Society
• /
• v.49 no.4
• /
• pp.363-368
• /
• 2012

Nitriding and post-sintering behavior of powder mixture compacts were investigated. As mixture compacts are different from simple Si compacts, the fabrication of a sintered body with a mixture composition has engineering implications. In this research, in specimens without a pore former, the extent of nitridation increased with $Si_3N_4$ content, while the highest extent of nitridation was measured in $Si_3N_4$-free composition when a pore former was added. Large pores made from the thermal decomposition of the pore former collapsed, and they were filled with a reaction product, reaction-bonded silicon nitride (RBSN) in the $Si_3N_4$-free specimen. On the other hand, pores from the decomposed pore former were retained in the $Si_3N_4$-added specimen. Introduction of small $Si_3N_4$ particles ($d_{50}=0.3{\mu}m$) into a powder compact consisting of large silicon particles ($d_{50}=7{\mu}m$) promoted close packing in the green body compact, and resulted in a stable strut structure after decomposition of the pore former. The local packing density of the strut structure depends on silicon to $Si_3N_4$ size ratio and affected both nitriding reaction kinetics and microstructure in the post-sintered body.

• Journal of the Korean Ceramic Society
• /
• v.39 no.1
• /
• pp.86-91
• /
• 2002

Solid Oxide Fuel Cells (SOFC) are of great interest of next generation energy conversion system due to their high energy efficiency and environmental friendliness. The basic SOFC unit consists of anode, cathode and solid electrolyte. Among these components, anode plays the most important role for the oxidation of fuel to generate electricity and also behaves as a substrate of the whole cell. It is normally requested that the anode materials should have the high electrical conductivity and gas permeability to reduce the polarization loss of the cell. In this study, the effect of pore former on the microstructure of anode substrate was investigated and thus on the electrical conductivity and the gas permeability. According to the results, microstructure and electrical conductivity of anode substrate were greatly influenced by the shape of pore former and especially by the anisotrpy of the pore former. The use of anisotropic pore former is supposed to deteriorate the cell performance by which the electrical conduction path is disconnected but also the effective gas diffusion path for the fuel is reduced.

• Journal of Powder Materials
• /
• v.18 no.6
• /
• pp.502-509
• /
• 2011

In this study, a novel-processing route for fabricating microcellular zirconia ceramics has been developed. The proposed strategy for making the microcellula zirconia ceramics involved hollow microspheres as pore former. Compared to conventional dense microspheres pore former, well-defined pore structured zirconia ceramics were successfully fabricated. Effects of hollow microsphere content and sintering temperature on microstructure, porosity, pore distribution, and strength were investigated in the processing of microcellular zirconia ceramics.

• Journal of the Korean Ceramic Society
• /
• v.35 no.3
• /
• pp.273-279
• /
• 1998

Unite cell of soid oxide fuel cell (SOFC) that consists of a dense yttria-stabilized zirconia(YSZ) electrolyte a porous nickel-YSZ cermet anode and a porous strontium- doped lanthanum manganate(LSM) cathod was fabricated from using pore former through co-firing technique. Initial sintering shrinkage rates of each layer were identified for fabricating SOFC. Heterogenous sintering was very effective in tailoring shrinkage rate for three layers. The powder tailoring necessary for shrinkage rate matching are as follows ; electrolyte of 60% TZ8YS/ 40% TZ8Y mixture anode of 51wt% NiO/49 wt% (70wt% TZ8YS/30 wt% UT ZrO2) mixture and cathode of 80% LSM/20% UT ZrO2 mixture . The overall sintering shrinkage rate differences of three layers using these compositions were maintained in a few percent.

• Journal of Pharmaceutical Investigation
• /
• v.41 no.4
• /
• pp.217-225
• /
• 2011

The aim of this work was to prepare porous osmotic pump tablets for controlled delivery of Aceclofenac. Aceclofenac solid dispersion was prepared to improve the solubility by using the drug - carrier (Mannitol) ratio of 1:1. The osmotic pump tablets were prepared using the solid dispersed product of Aceclofenac. The formulation contains potassium chloride as osmotic agent, cellulose acetate as semipermeable membrane, poly ethylene glycol (PEG 4000) as pore former and sodium lauryl sulphate (SLS) as solubility enhancer. The formulations were designed by the general factors such as osmotic agent and pore former. All formulations were evaluated for various physical parameters and, the in vitro release studies were conducted as per USP. The drug release kinetic studies such as zero order, first order, and Higuchi and Korsmeyer peppas were determined and compared. All the formulations gave more controlled release compared to the marketed tablet studied. Numerical optimization techniques were applied to found out the best formulation by considering the parameter of in vitro drug release kinetics and dissolution profile standards. It was concluded that the porous osmotic pump tablets (F7) composed of Aceclofenac solid dispersion/Potassium chloride/Lactose/Sodium lauryl sulphate/Magnesium Stearate (400/40/95/10/5, mg/tab) and coating composition with Cellulose acetate/ PEG 4000 (60/40 %w/w) is the most satisfactory formulation. The porous osmotic pump tablets provide prolonged, controlled, and gastrointestinal environment-independent drug release.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1999.10a
• /
• pp.214.1-214
• /
• 1999

• The Bulletin of The Korean Astronomical Society
• /
• v.38 no.1
• /
• pp.66.2-66.2
• /
• 2013

In this study, we present a pore-selection technique to estimate the size of pore. The estimation of the size of pore is important to examine the temporal evolution of size itself and corresponding intensity. The size of pore is typically estimated by applying the intensity threshold technique to the fixed box which contains the entire pore. The typical method has disadvantages in the following circumstances; there are small features near the pore or the image has low spatial resolution. In the former, it is difficult to define a box containing the pore only, excluding the small features near the pore. In the latter, the background and threshold intensity are insignificant due to the insufficient number of pixel in the box. To avoid these difficulties, we use a pore-selection technique which is simply based on the measurement of distances from the pore center. In addition, we will discuss the advantage of the technique for the imaging spectrograph data like the NST FISS.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.10
• /
• pp.2759-2760
• /
• 2010