• Nuclear Engineering and Technology
• /
• 제23권1호
• /
• pp.49-55
• /
• 1991

AUC공정으로 제조된 $UO_2$분말을 사용하여 소결체를 제조하여 미세 조직과 기공특성에 대하여 시험하였다. 개기공은 소결밀도 증가에 따라서 감소하였으며, 소결밀도 10.45 g/㎤ 이상에서는 거의 소멸하였다. 3$\mu$m보다 작은 크기의 둥근 기공이 모든 밀도에서 나타났고 낮은 밀도에서는 이것외에도 긴 기공이 관찰되었다. 같은 크기의 기공일지라도 밀도가 낮아지면 기공이 더욱 길게 나타났다. 기공크기에 따른 기공 면적의 분포는 mono 모우드이고, 2~3$\mu$m 기공크기에서 최대치를 보이는 분포를 보였다. 또한 밀도가 감소할수록 큰 기공에 관련된 면적이 증가하였다.

• 한국세라믹학회지
• /
• 제40권6호
• /
• pp.572-576
• /
• 2003

$UO_2$-20 wt% CeO$_2$ 소결 펠렛의 밀도에 따른 개/폐 기공도, 기공의 크기 및 그 분포 그리고 기공의 형태를 조사하였다. 이론 소결밀도 약 96% 이상에서는 기공도는 개기공이 거의 없는 폐기공으로 나타났다. 반면에 기공크기 분포는 소결밀도에 관계없이 bimodal 형태를 보이나, 소결밀도가 증가할수록 기공 개수만 적게 나타났다. 기공의 형태는 소결밀도가 증가할수록 불규칙한 형태에서 둥근 형태로 바뀌었다.

• 한국화재소방학회논문지
• /
• 제11권3호
• /
• pp.15-23
• /
• 1997

In this study, the alumina for gas sensor was prepared by anodic oxidation. It was stable thermally and chemically, and pore diameter and pore distribution was uniform. And the shape of pore was cylinderical. The aluminum plate was carried out by the thermal oxidation, chemical polishing and electropolishing pretreatment. The pore diameter, pore size distribution, pore density and thickness of alumina was observed with the change of reaction temperature, electrolyte concentration and current density. As a results, It was able to use for carrier because alumina which was prepared by anodic oxidationhas uniform pore size distribution.

• Geomechanics and Engineering
• /
• 제7권5호
• /
• pp.553-567
• /
• 2014

Borehole instability during drilling process occurs frequently when drilling through shale formation. When a borehole is drilled in shale formation, the low permeability leads to an undrained loading condition. The pore pressure in the compressed area near the borehole may be higher than the initial pore pressure. However, the excess pore pressure caused by stress concentration was not considered in traditional borehole stability models. In this study, the calculation model of excess pore pressure induced by drilling was obtained with the introduction of Henkel's excess pore pressure theory. Combined with Mohr-Coulumb strength criterion, the calculation model of collapse pressure of shale in undrained condition is obtained. Furthermore, the variation of excess pore pressure and effective stress on the borehole wall is analyzed, and the influence of Skempton's pore pressure parameter on collapse pressure is also analyzed. The excess pore pressure decreases with the increasing of drilling fluid density; the excess pore pressure and collapse pressure both increase with the increasing of Skempton's pore pressure parameter. The study results provide a reference for determining drilling fluid density when drilling in shale formation.

• 한국초지조사료학회지
• /
• 제7권2호
• /
• pp.109-112
• /
• 1987

tall fescue의 밀도변화에 미치는 토양경화는 공극율의 영향에 대하여 조사하였다. 1. 토양경화에 따라서 토양경도와 용적중은 증가되었다. (Table 1). 2. 10kg 처리구(토양경도 2.5kg/$\textrm{cm}^3$)의 밀도가 타처리구보다 유의하게 높았다. (Table 2, Fig. 1). 3. 토양공성율과 밀도와는 상관계수가 0.9804로써 1%수준의 정상란이 인정되었다. 4. 경화된 토양에서는 공성율이 37.5% 이상일 때 높은 밀도를 나타내었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제33권2호
• /
• pp.244-251
• /
• 2009

Porous media have especially large surface area per volume, which contain complex fluid passage. If porous media can be applied to cool a CPU or an electronic device with large heat dissipation, it could result in heat transfer enhancement due to the enlargement of the heat transfer area and the flow disturbance. This study is aimed to identify the heat transfer and pressure drop characteristics of high-porosity metal foams in a horizontal channel. Experiment is performed with the various heat flux, velocity and pore density conditions. Permeabilities, which is deduced from Non-Darcy flow model, become lower with increasing pore density. Nusselt number also decreases with higher pore density. High pore density with same porosity case shows higher pressure loss due to the increase of surface area per unit volume. The fiction factor decreases rapidly with increase of Reynolds number in Darcy flow region. However, it converges to a constant value of the Ergun coefficient in Non-Darcy flow region.

• 한국초전도ㆍ저온공학회논문지
• /
• 제16권1호
• /
• pp.19-22
• /
• 2014

The effects of Mg content on the pore formation, density and critical properties were investigated in in-situ reacted $MgB_2$ superconductors. The $Mg_{1+x}B_2$, (x=-0.2, 0.0, 0.05, 0.3, 1.0) bulk samples with different Mg contents were heat-treated at $900^{\circ}C$ for 1 h in an Ar atmosphere. The dimensional changes of a pellet's mass and volume after heat-treatment were measured. After heat-treatment process, the sample mass was decreased by Mg evaporation, but the sample volume was expanded by pore formation at the Mg site; therefore, the apparent density was decreased. Spherical pores the same as Mg particles were developed after heat-treatment in all samples, and the pore density was increased with increasing Mg content. As the x of Mg content was increased to 1.0, the apparent density of $Mg_{1+x}B_2$ samples was decreased due to a relatively larger reduction in a mass change. The critical current density of Mg excessive sample of x=0.05 showed the highest values over the applied magnetic fields because the excessive Mg may compensate Mg loss and enhance grain connectivity.

• Carbon letters
• /
• 제3권2호
• /
• pp.85-92
• /
• 2002

4D carbon fiber preforms were manufactured by weaving method and their carbon fiber volume fractions were 50% and 60%. In order to form carbon matrix on the preform, coal tar pitch was used for matrix precursor and high density carbon/carbon composites were obtained by high densification process. In this process, manufacture of high density composites was more effective according to pressure increasement. When densificating the preform of 60% fiber volume fraction with 900 bar, density of the composites reached at 1.90 $g/cm^3$ after three times processing. Degree of pressure in the densification process controls macro pore but it can not affect micro pore. During the carbonization process, micro pore of the preform were filled fully by once or twice densification processing. But micro pore were not filled easily in the repeating process. Therefore, over three times densification processing is the filling micro pore.

• 한국세라믹학회지
• /
• 제36권8호
• /
• pp.782-790
• /
• 1999

The compressibility sinterability sintering behaviour and thermal stability of AlOOH added UO2 pellt and PVA-Al(III) complex added UO2 pellet were investigated respectively. Compared with characteristics of AlOOH added UO2 pellet the green density and the sintered density of PVA-Al(III) complex added UO2 pellet were lowered but the grain size and the pore size of that were more increased in accordance with higher compacting pressure. The AlOOH added UO2 pellet had the grain size of about 14${\mu}{\textrm}{m}$ with monomodal pore size distribution while the PVA-Al(III) complex added UO2 pellet had the grain size of about 42 ${\mu}{\textrm}{m}$ with bimodal pore size distribution. The PVA-A(III) complex added UO2 pellet had a similiar open porosity to the AlOOH added UO2 pellet and a lower resintered density change than the AlOOH added UO2 pellet.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 춘계학술발표강연 및 논문개요집
• /
• pp.53-53
• /
• 2003

There has been increasing interest in the fabrication of nano-sized structures because of their various advantages and applications. Anodic Aluminum Oxide (AAO) is one of the most successful methods to obtain highly ordered nano pores and channels. Also It can be obtained diverse pore diameter, density and depth through the control of anodization condition. The three types of substrates were used for anodization; sheets of Aluminum on Si wafer and Aluminum on Mo-coated Si wafer. In Aluminum sheet, a highly ordered array of nanoholes was formed by the two step anodization in 0.3M oxalic acid solutions at 10$^{\circ}C$ After the anodization, the remained aluminum was removed in a saturated HgCl$_2$ solution. Subsequently, the barrier layer at the pore bottom was opened by chemical etching in phosphoric acid. Finally, we can obtain the through-channel membrane. In these processes, the effect of various parameters such as anodizing voltage, anodizing time, pore widening time and pre-heat treatment are characterized by FE-SEM (HITACH-4700). The pore size. density and growth rate of membrane are depended on the anodizing voltage and temperature respectively. The pore size is proportional to applied voltage and pore widening time The pore density can be controlled by anodizing temperature and voltage.