• Nuclear Engineering and Technology
• /
• 제52권10호
• /
• pp.2353-2360
• /
• 2020

An anodic electrophoretic deposition (EPD) technique is used to create a uniform TiO₂ thin film coating on boiling thin steel plates (1.1 mm by 90 mm). All of the effective parameters except time of the EPD method are kept constant. To investigate the effect of gamma irradiation on the critical heat flux (CHF), the test specimens were irradiated in a gamma cell to different doses ranging from 100 to 300 kGy, and then SEM and BET analysis were performed. For each coated specimen, the contact angle and capillary length were measured. The specimens were then tested in a boiling pool for CHF and boiling heat transfer coefficient. It was observed that irradiation significantly decreases the maximum pore diameter while it increases the porosity, pore surface area and pore volume. These surface modifications due to gamma irradiation increased the CHF of the nano-coated surfaces compared to that of the unirradiated surfaces. The heat transfer coefficient (HTC) of the nano-coated surfaces irradiated at 300 kGy increased from 83 to 160 kW/(㎡ K) at 885 kW/㎡ wall heat flux by 100%. The CHF of the irradiated (300 kGy) and unirradiated surfaces are 2035 kW/㎡ and 1583 kW/㎡, respectively, an increase of nearly 31%.

• 한국세라믹학회지
• /
• 제37권1호
• /
• pp.26-32
• /
• 2000

Preparation and characteristics of a matrix retaining electrolyte using SiC whisker, PES binder, and NMP(n-methyl-2-pyrrolidone) as a non-volatile solvent for a phosphoric acid fuel cell were investigated. The conditions of binder and plasticizer, and the effects of substituting a volatile solvent by a non-volatile solvent were also studied. The minimum amount of the binder was about 17 wt% for the proper bubble pressure and surrounding SiC whiskers. And the maximum amount of the plasticizer was about 10wt% to be fitted into the polymer chain of the binder. The matrix prepared by using a non-volatile solvent needed longer time to dry, and its pore size was smaller compared with that of the matrix prepared by using volatile solvent. The small pore size resulted in decrease of the overall pore volume. The ionic conductivity in the condition of the same thickness was decreased due to decrease of phosphoric acid absorbancy. As the internal resistance of the electrolyte increased, the fuel cell performance slightly decreased.

• 한국재료학회지
• /
• 제26권2호
• /
• pp.61-66
• /
• 2016

In order to fabricate porous mullite ceramics with controlled pore structure and improved mechanical strength, a freeze casting route has been processed using camphene mixed with tertiary-butyl alcohol (TBA) and coal fly ash/alumina as the solvent and the ceramic material, respectively. After sintering, the solidification characteristics of camphene and TBA solvent were evident in the pore morphology, i.e., dendritic and straight pore channels formed along the solidification directions of camphene and TBA ice, respectively, after sublimation. Also, the presence of microcracks was observed in the bodies sintered at $1500^{\circ}C$, mainly due to the difference in solidification volume change between camphene and TBA. The compressive strength of the sintered bodies was found generally to be dependent, in an inverse manner, on the porosity, which was mainly determined by the processing conditions. After sintering at $1300{\sim}1500^{\circ}C$ with 30~50 wt% solid loading, the resulting mullite ceramics showed porosity and compressive strength values in ranges of 83.8~43.1% and 3.7~206.8 MPa, respectively.

• Geomechanics and Engineering
• /
• 제15권3호
• /
• pp.851-859
• /
• 2018

There are two primary causes of the ground movement due to tunnelling in urban areas; firstly the lost ground and secondly the groundwater depression during construction. The groundwater depression was usually not considered as a cause of settlement in previous research works. The main purpose of this study is to analyze the combined effect of these two phenomena on the transverse settlement trough. Centrifuge model tests and numerical analysis were primarily selected as the methodology. The characteristics of settlement trough were analyzed by performing centrifuge model tests where acceleration reached up to 80g condition. Two different types of tunnel models of 180 mm diameter were prepared in order to match the prototype of a large tunnel of 14.4 m diameter. A volume loss model was made to simulate the excavation procedure at different volume loss and a drainage tunnel model was made to simulate the reduction in pore pressure distribution. Numerical analysis was performed using FLAC 2D program in order to analyze the effects of various groundwater depression values on the settlement trough. Unconfined fluid flow condition was selected to develop the phreatic surface and groundwater level on the surface. The settlement troughs obtained in the results were investigated according to the combined effect of excavation and groundwater depression. Subsequently, a new curve is suggested to consider elastic settlement in the modified Gaussian curve. The results show that the effects of groundwater depression are considerable as the settlement trough gets deeper and wider compared to the trough obtained only due to excavation. The relationships of maximum settlement and infection point with the reduced pore pressure at tunnel centerline are also suggested.

• 한국연초학회지
• /
• 제18권1호
• /
• pp.85-91
• /
• 1996

Commercially available activated carbon was treated with 0.2N NaOH/0.1N HCl to decrease the ash contents and to analyze the effect of demineralization. We have studied their properties and adsorptivity to solvents such as benzene, acetone, toluene and carbon tetrachloride, ammonia and also aldehydes of cigarette smoke. By demineralization with NaOH/HCl, surface area and pore volume were increased up to 10 - 20% according to developement of micro-pore and pH of activated carbon was also changed from 10.2 to 6.3. Surface acidity of the activated carbon treated with chemicals increased slightly. The chemical treatment led to small increase in adsorptioil properties of solvents, ammonia and aldehydes of cigarette smoke, but content of chlorine and sulfur in activated carbon were reduced. As the results of smoking test, charcoal taste caused by the activated carbon was reduced significantly by the treatment with NaOH/HCl.

• Bulletin of the Korean Chemical Society
• /
• 제33권5호
• /
• pp.1699-1702
• /
• 2012

$TiO_2$ nanostructures with various morphologies like cubes, spheres, hexahedral pillars and spherical tubes were synthesized by microwave-assisted hydrothermal process. Each structure was obtained by changing the relative concentrations of titanium tetraisoproxide (TTIP), tetrabutylammonium hydroxide (TBAH) and ethanol. Scanning electron microscopy (SEM), transmission electoron microscopy (TEM), X-ray diffraction and Brunauer-Emmett-Teller (BET) surface area analysis were used to characterize the synthesized $TiO_2$ nanostructures. From these results, it has been proved that $TiO_2$ structure could be controlled to have specific morphology, size, surface area, pore volume and pore size distribution.

• Bulletin of the Korean Chemical Society
• /
• 제27권3호
• /
• pp.399-402
• /
• 2006

Porous organic-inorganic hybrids have been prepared from tetraethylorthosilicate (TEOS) and organosilane precursors by sol-gel method. Two organosilanes, 3-(2,4-dinitrophenylamino)propyltriethoxysilane (DNPTES) and N-[[(2-nitrophenyl)methoxy]carbonyl]-3-triethoxysilylpropylamine (NPTES) were used to incorporate electron-accepting (di)nitrophenyl groups into the hybrids. The hybrids were characterized by FT-IR spectroscopy and elemental analysis, and their pore characteristics were studied by nitrogen sorption porosimetry. Surface area of the hybrids ranged from 563 to 770 $m^2$/g, pore volume, 0.23-0.30 $cm^3$/g, and porosity, 35-41%. It was demonstrated by UV-vis spectroscopy that aniline, ethylenediamine, and 1-aminonaphthalene could be removed from their hexane solutions in the presence of the hybrid powders. The removal of amines is attributable to donor-acceptor interaction between the electron-donating amines and electron-accepting (di)nitrophenyl moiety.

• 펄프종이기술
• /
• 제30권4호
• /
• pp.79-84
• /
• 1998

The process of double coating consists of bottom coating using relatively coaser pigments to improve characteristics of base paper and top coating using finer pigments to cover unevenness of the bottom coating and to give various function of the coated paper. The structure of precoating is influenced not only by its components, but also characteristics of base paper, Moreover pore size and its size distribution of precoating are expected to influence the top coating properties, but this is not well understood. Coating and printing operations involve the application of pigmented fluid on top of a porous substrate. The porosity of the substrate has been shown to influence the properties of the coating, but a good understanding of the mechanisms is lacking in the literature. The role of pore size and void volume on top coating structure is unclear.

• Carbon letters
• /
• 제4권3호
• /
• pp.140-145
• /
• 2003

Antibacterial behaviors of PAN-based activated carbon fibers (ACFs) containing silver metal were investigated. The effects of surface and pore structures of the ACFs were studied by $N_2$/77 K adsorption and D-R plot as a function of silver loading content. The antibacterial activities were investigated by a dilution test against Staphylococcus aureus (S. aureus; gram positive) and Klebsiella pnemoniae (K. pnumoniae; gram negative). As experimental results, the ACFs showed some decreases in specific surface areas, micropore volumes, and total pore volume with an increase of silver content. However, the antibacterial activities of the ACFs were strongly increased against S. aureus as well as K. pnumoniae, which could be attributed to the presence of antibacterial metal in the ACFs system.

• Carbon letters
• /
• 제6권4호
• /
• pp.248-254
• /
• 2005

Silver impregnated activated carbon fibers were post-modified using hydrochloric acid. Adsorption behaviors, SEM morphologies, and functional groups for the silver impregnated ACFs were compared with those of post-modified ACFs. Adsorption isotherms were used to characterize $S_{BET}$, the pore structure and volume of silver-activated carbon fibers (ACFs) before and after acid post-treatment. In order to the reveal the causes of the differences surface states after the samples were washed with hydrochloric acid, outer surface and pore structure were investigated by SEM. And the type and quality of various functional groups were studied from FT-IR spectra and Boehm titration method. Finally, the quantitative properties in silver contents were also examined by EDX spectra.