• Restorative Dentistry and Endodontics
• /
• v.25 no.1
• /
• pp.17-40
• /
• 2000

Resin cements are used for cementing indirect esthetic restorations such as resin or porcelain inlays. Because of its limitations in curing of purely light cured resin cements due to attenuation of the curing light by intervening materials, dual cured resin cements are recommended for cementing restorations. The physical properties of resin cements are greatly influenced by the extent to which a resin cures and the degree of cure is an important factor in the success of the inlay. The purpose of this study was to evaluate the influence of porcelain thickness and exposure time on the polymerization of resin cements by measuring the microhardness and the degree of conversion, to investigate the nature of the correlation between two methods mentioned above, and to determine the exposure time needed to harden resin cements through various thickness of porcelain. The degree of resin cure was evaluated by the measurements of microhardness [Vickers Hardness Number(VHN)] and degree of conversion(DC), as determined by Fourier Transform Infrared Spectroscopy(FTIR) on one light cured composite resin [Z-100(Z)] and three dual cured resin cements [Duo cement(D), 3M Resin cement(R), and Dual cement(DA)] which were cured under porcelain discs thickness of 0mm, 1mm, 2mm, 3mm with light exposure time of 40sec, 80sec, 120sec, and regression analysis was performed to determine the correlation between VHN and DC. In addition, to determine the exposure time needed to harden resin cements under various thickness of porcelain discs, the changes of the intensity of light attenuated by 1mm, 2mm, and 3mm thickness of porcelain discs were measured using the curing radiometer. The results were obtained as follows ; 1. The values of microhardness and the degree of conversion of resin cements without intervening porcelain discs were 31~109VHN and 51~63%, respectively. In the microhardness Z was the highest, followed by R, D, DA. In the degree of conversion, D and DA was significantly greater than Z and R(p<0.05). 2. The microhardness and the degree of conversion of the resin cements decreased with increasing thickness of porcelain discs, and increased with increasing exposure time, D and R showed great variation with inlay thickness and exposure time, whereas, DA showed a little variation. 3. The intensity of light through 1mm, 2mm, and 3mm porcelain inlays decreased by 0.43, 0.25, and 0.14 times compared to direct illumination, and the respective needed exposure times are 53 sec, 70 sec, and 93 sec. In D and R, 40 sec of light irradiation through 2mm porcelain disc and 80 sec of light irradiation through 3mm porcelain disc were not enough to complete curing. 4. The microhardness and the degree of conversion of the resin cements showed a positive correlationship(R=0.791~0.965) in the order of R, D, Z, DA. As the thickness of porcelain discs increased, the decreasing pattern of microhardness was different from that of the degree of conversion, however.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.11
• /
• pp.1531-1540
• /
• 2002

With the invention of the inlaying technique for celadon in the latter half of the 12th century, the Koryo potters reached a new height of artistic and scientific achievement in ceramics chemical technology. Inlaid celadon shards, collected in 1991 during the surface investigation of Kangjin kilns found on the southwestern shore of South Korea, were imbedded in epoxy resin and polished for cross-section examination. Backscattered electron images were taken with an electron microprobe equipped with an energy dispersive spectrometer. The spectrometer was also used to determine the composition of micro-areas. Porcelain stone, weathered rock of quartz, mica, and feldspar composition were found to be the raw material for the body and important components in the glaze and white inlay. The close similarity between glaze and black inlay in the microstructure suggests that the glaze material was modified by adding clay with high iron content, such as biotite, for use as black inlay. The deep soft translucent quality of celadon glaze is brought about by its microstructure of bubbles, remnant and devitrified minerals, and the schlieren effect.

• The Journal of Korean Academy of Prosthodontics
• /
• v.38 no.3
• /
• pp.366-374
• /
• 2000

FRC/ceromer system provides the clinician with a durable, flexible, and esthetic alternative to conventional porcelain fused to metal crowns. FRC is the matrix which is silica-coated and embedded in a resin matrix. The ceromer material which is a second generation indirect composite resin contains silanized, microhybrid inorganic fillers embedded in a light-curing organic matrix. FRC/ceromer restoration has a several advantages: better shock absorption, less wear of occluding teeth, translucency, color stability, bonding ability to dental hard tissues, and resiliency. It has versatility of use including inlay, onlay, single crown, and esthetic veneers. With adhesive technique, it can be used for single tooth replacement in forms of inlay adhesion bridge. In single tooth missing case, conventional PFM bridge has been used for esthetic restoration. However, this restoration has several disadvantages such as high cost, potential framework distortion during fabrication, and difficulty in repairing fractures. Inlay adhesion bridge with FRC/ceromer would be a good alternative treatment plan. This article describes a cases restored with Targis/Vectris inlay adhesion bridge. Tooth preparation guide, fabrication procedure, and cementation procedure of this system will be dealt. The strength/weakness of this restoration will be mentioned, also. If it has been used appropriately in carefully selected case, it can satisfy not only dentist's demand of sparing dental hard tissue but also patient's desire of seeking a esthetic restorations with a natural appearance.

• Proceedings of the KACD Conference
• /
• 2001.11a
• /
• pp.595-595
• /
• 2001

As the interest for esthetic restoration is increasing, the usage of composite resin is increasing. The usage of composite resin is not limited to anterior teeth but is spreading to posterior area using direct ＆ indirect methods. Generally, dual or chemical cure resin cement has been used for setting composite or porcelain inlay restoration. However, chemical cure resin cement has limited working time and it's difficult to remove excess cement from the tooth and the restoration. The dual cured composite is also difficult to remove from the tooth surface.(omitted)

• Restorative Dentistry and Endodontics
• /
• v.23 no.1
• /
• pp.487-501
• /
• 1998

In the case of CAD/CAM ceramic inlay restorations, if isthmus width is widened too much, it may cause fracture of remaining tooth structure or loss of bonding at the luting interface because of excessive displacement of buccal or lingual cusps under occlusal loads. So to clarify the criterior of widening isthmus width, this study was designed to test the tensile bond strength and bond failure mode between dentin and ceramic cemented with luting composite resin cements. Cylindrical ceramic blocks(Vita Cerec Mark II, d=4mm) were bonded to buccal dentin of 40 freshly extracted third molars with 4 luting composite resin cements(group1 : Scotchbond Resin Cement/Scotchbond Multi-Purpose, group2 : Duolink Resin Cement/ All-Bond 2, group3: Bistite Resin Cement/Ceramics Primer, and group4:Superbond C&B). Tensile bond test was done under universal testing machine using bonding and measuring alignment blocks(${\phi}ilo$ & Urn, 1992). After immersion of fractured samples into 1 % methylene blue for 24 hours, failure mode was analysed under stereomicroscope and SEM. Results: The tensile bond strength of goup 1, 2 & 4 was $13.97{\pm}2.90$ MPa, $16.49{\pm}3.90$ MPa and $16.l7{\pm}4.32$ MPa, respectively. There was no statistical differences(p>0.05). But, group 3 showed significantly lower bond stregnth($5.98{\pm}1.l7$ MPa, p<0.05). In almost all samples, adhesive fractures between dentin and resin cements were observed. But, in group 1, 2 & 4, as bond strength increased, cohesive fracture within resin cement was observed simultaneously. And, in group 3, as bond strength decreased, cohesive fracture between hybrid layer and composite resin cement was also observed. Cohesive fracture within dentin and porcelain adhesive fracture were not observed. In conclusion, although adhesive cements were used in CAD/CAM -fabricated ceramic inlay restorations, the conservative priciples of cavity preparation must be obligated.

• Restorative Dentistry and Endodontics
• /
• v.23 no.2
• /
• pp.647-655
• /
• 1998

심미도재수복시의 와동의 폭과 교두의 capping이 응력의 분포에 미치는 영향을 비교하기 위하여 연속사진 촬영술을 이용하여 상악제1소구치의 3차원 유한요소 모델을 제작하였다. 법랑질, 상아질, 도재 및 복합레진시멘트의 각각의 재질에 대한 물성치를 부여하고, 140N의 하중을 가하여 Super SAP 프로그램으로 해석하여 다음과 같은 결과를 얻었다. 1. 응력은 탄성계수값이 큰 법랑질과 도재를 따라 분포되고, 연질의 상아질에는 적게 발생된다. 2. 와동의 협측치수선각부위에서는 인레이모델의 경우에는 와동폭의 증가에 따른 응력의 증가는 관찰되지 않으나, 온레이모델에서는 응력의 증가가 관찰된다. 3. 온레이모델의 경우에는 근심협측교두를 피개하고 있는 도재부위에 최대주응력이 크게 나타나고, 치은변연부의 도재에서는 교두를 피개하지 않은 인레이모델의 해당되는 법랑질에 비해 응력이 1/2정도로 감소된다. 4. 하중이 증가되면 잔존치질의 파절은 근심와동의 협측치은선각부위에서 협측보다는 치은을 향해 경사지게 일어날 것이다. 5. 교두를 피개하면 교두피개부위에서의 도재의 파절가능성은 증가되고, 치은변연에서는 도재와 하부의 치질의 파절가능성은 감소된다. 6. 도재를 이용하여 교두를 피개할 경우에는 응력을 견딜 수 있는 도재의 두께를 부여할 수 있도록 교두를 충분히 삭제하여야 하고, 충분한 강도를 갖는 도재를 선택하여야 한다.

• Journal of Technologic Dentistry
• /
• v.12 no.1
• /
• pp.5-14
• /
• 1990

The purpose of this study were to investigate the patterns of prosthetic restorations according to sex and age. We had surveyed the out-patents of dental clinics it Jeon-Ju, Iri and Gun roan area. The abtained result were as follow ; 1. The patterns of prosthetic restoration in female was higher than male and 20$\sim$30 age groups was higher than others. 2. The crown was higher in prosthetic restoration. 3. The procelain appliance area was high in male and female on 20$\sim$29 age. 4. The partial denture was higher than full denture in both sex. 5. The crown appliance area was not different in both sex. 6. The 3 unit bridge was higher than other bridge in both sex. 7. The porcelain appliance area was high in male and female on upper anterior. 8. The inlay appliance area of lower posterior was higher than upper posterior. 9. The upper posterior was high in male, and the lower posterior was high in female in partial denture. 10. The full dentur was high in old age group.

• Proceedings of the KACD Conference
• /
• 2001.05a
• /
• pp.235-237
• /
• 2001

;Dentistry has benefited from tremendous advances in technology with the introduction of new techniques and materials, and patients are aware that esthetic approaches in dentistry can change one's appearance. Increasingly. tooth-colored restorative materials have been used for restoration of posterior teeth. Tooth-colored restoration for posterior teeth can be divided into three categories: 1) the direct techniques that can be made in a single appointment and are an intraoral procedure utilizing composites: 2) the semidirect techniques that require both an intraoral and an extraoral procedure and are luted chairside utilizing composites: and 3) the indirect techniques that require several appointments and the expertise of a dental technician working with either composites or ceramics. But, resin restoration has inherent drawbacks of microleakage. polymerization shrinkage, thermal cycling problems. and wear in stress-bearing areas. On the other hand, Ceramic restorations have many advantages over resin restorations. Ceramic inlays are reported to have less leakage than resin restoration and to fit better. although marginal fidelity depends on technique and is laboratory dependent. Adhesion of luting resin is more reliable and durable to etched ceramic material than to treated resin composite. In view of color matching, periodontal health. resistance to abrasion, ceramic restoration is superior to resin restorationl. Materials which have been used for the fabrication of ceramic restorations are various. Conventional powder slurry ceramics are also available. Castable ceramics are produced by centrifugal casting of heat-treated glass ceramics. and machinable ceramics are feldspathic porcelains or cast glass ceramics which are milled using a CAD/CAM apparatus to produce inlays (for example, Cered. They may also be copy milled using the Celay apparatus. Pressable ceramics are produced from feldspathic porcelain which is supplied in ingot form and heated and moulded under pressure to produce a restoration. Infiltrated ceramics are another class of material which are available for use as ceramic inlays. An example is $In-Ceram^{\circledR}$(Vident. California, USA) which consists of a porous aluminum oxide or spinell core infiltrated with glass and subsequently veneered with feldspathic porcelain. In the 1980s. the development of compatible refractory materials made fabrication easier. and the development of adhesive resin cements greatly improved clinical success rates. This case report presents esthetic ceramic inlays for posterior teeth.teeth.

• Journal of Technologic Dentistry
• /
• v.23 no.2
• /
• pp.75-93
• /
• 2002

This research was preformed for the purpose of preparing the items of standard model of the national dental technician test base on the duty analysis of the dental technician. The results of the duty analysis for the dental technician follows. 1. The dental technician is a profession to make the oral function smooth through the dental supplement and equipment in a scientific method and the skilled technique. 2. The duty of the dental technician are determined as A. preparation for manufacture B. manufacture C. management of the place of the dental technology D. self-development. A. The field of "the preparation for manufacture" are determined as 1. to confirm work authorization 2. To confirm the working model, B. The field of "In manufacture" are determined as 1. to manufacture the temporary crown 2. to manufacture the inlay and crown & bridge prosthesis 3. to manufacture the porcelain fused metal crown prosthesis 4. to manufacture the all ceramic crown prosthesis 5. to manufacture the temporary denture prosthesis 6. to manufacture the partial denture prosthesis 7. to manufacture the complete denture prosthesis 8. to manufacture the attachment prosthesis 9. to manufacture implant prosthesis 10. to manufacture the removable orthodontic device, 11. to manufacture the fixed orthodontic device, 12. to manufacture the orthodontic study cast C. The field of "in management of the dental lab." are determined as 1. management 2. to control the dental lab. D. The field of "In the self-development" are determined as 1. to improve the professionalism 2. self-control. 3. The developing items selected under the duty evaluation of the dental technician are l7s in the manufacture preparation, 1,011s in the manufacture, 7s in the management for the dental technology, 5s in self-development, and in all together 1,040s

• The Journal of Korean Academy of Prosthodontics
• /
• v.18 no.1
• /
• pp.99-109
• /
• 1980

An investigation was made Into 1,357 fixed bridges which had been performed at the Department of Prosthetic Dentistry, Seoul National University Hospital from 1973 to 1979. The purpose of this investigation was to establish a basic reference of the treatment with fixed bridges by obtaining statistical conclusions from the data concerning the patients who had been treated with fixed bridges. The following conclusions were obtained; 1. The ratio of the fixed bridges made on the maxillae to those made on the mandible was 1:1. 2. The cases of fixed bridges with one pontic were the most frequent, i.e., 946 cases out of total 1,357 cases, which were 69.7% of the total. 3. As the number of missing teeth increased, the number of the relevant cases of fixed bridges decreased. 4. The most frequent age group of the patients who had been treated with fixed bridges was the twenties, which was 40.8% of the total. As the age of the patients increased, the number of corresponding cases of fixed bridges decreased. 5. Most of the fixed bridges with more than three pontics were made at the anterior portion samely on the maxilla and on the mandible. 6. As for the retainers, the porcelain fused to metal crown and the partial veneer crown were frequently used at the anterior portion, while the full veneer crown was frequently used and the inlay and the attachment were used in some cases at the posterior portion. The locations of fixed bridges in the order of their frequency were: canine, lateral incisor, second bicuspid, central incisor, second molar, first bicuspid, first molar, and third molar on the maxilla; second bicuspid, second molar, first bicuspid, first molar, canine, third molar, lateral incisor, and central incisor on the mandible.