• 치위생과학회지
• /
• 제13권3호
• /
• pp.290-295
• /
• 2013

본 연구는 심미 치과보철물에 사용되는 지르코니아, lithium disilicate 코어와 전장도재 사이의 전단결합강도를 측정하고, 금속도재관을 대조군으로 설정하여 비교하였다. 직사각기둥 모양의 시편을 각각 10개씩 제작하여 코어와 전장도재 사이의 전단결합강도를 측정한 후 파절면의 양상을 실체현미경을 통해 관찰하였다. 제한된 조건하에 시행된 실험을 통하여 심미보철 분야에 널리 적용되고 있는 치과용세라믹 코어의 전단결합강도를 확인하였으며, 측정 후 비교분석된 결과는 다음과 같다. 2종의 치과용 세라믹 코어와 전장도재 간에 전단결합강도는 금속도재관의 전단결합강도와 유의한 차이가 있었다 (p<0.05). 본 실험 결과를 토대로 ZB군은 임상적으로 받아들여지는 전단결합강도 범위 내 분포를 보이지만, LB군은 임상허용 범위에 못 미치는 결과값을 보였다. 금속도재관과 달리 지르코니아, lithium disilicate 전부도재관은 모두 혼합형 파절양상을 보였다. 결론적으로 전단결합강도 실험에 사용된 시편이 임상적인 치과보철물의 형태와는 달리 실험을 위한 시편의 형태로 제작되어 임상적 결과를 반영하지 못했으며 구강 내의 상황과도 다르다는 한계점을 가지고 있다. 추후에는 이를 보완하여 치과보철물과 유사한 형태의 시편을 이용한 전단결합 강도의 측정과 구강 내 조건을 고려한 추가 실험이 필요하다고 생각된다.

• Restorative Dentistry and Endodontics
• /
• 제24권3호
• /
• pp.473-481
• /
• 1999

This study evaluated the shear bond properties of IPS Empress glass ceramic to enamel and dentin surfaces with three ceramic surface treatments, and three resin cements. The influence of thermocycling was also investigated. The purpose of this study was to investigate the influences of resin cements, ceramic surface treatments, and thermocycling on shear bond properties. Ninety freshly extracted, noncarious human molars were selected for this study. The surface treatments of ceramic were etching <5.0% hydrofluoric acid, application of silane coupling agents(Tokuso Ceramic Primer, Clearfil porcelain bond, Monobond-S), and the combination of the two methods. Empress cylinders were bonded to enamel and dentin surfaces with three kinds of resin cements(Bistite resin cement, Panavia 21, Variolink). The specimens were aged in $37^{\circ}C$ distilled water for 24 hours. Half of the specimens were then thermocycled 500times between $5^{\circ}C$ and $55^{\circ}C$ with a dwell time of 15 seconds. Each specimen was debonded in shear mode and measured shear bond properties by using the universal testing machine(Zwick 020, Germany). The data were analyzed by SPSS/PC+(one-way ANOVA, Scheffe' s test and t-test). The results were as follows : 1. Without thermocyling, there was significant difference of shear bond strength to enamel surface between Bistite Resin Cement and Panavia 21 in case of etched and silane-treatment(p<0.05). 2. Without thermocyling, the shear bond strength of a group treated with silane and etching was significantly higher than that of a group treated with silane or etching with the application of Panavia 21 and Variolink(p<0.05). 3. A group treated with etching with the application of Variolink only showed a decrease of shear bond strength after thermocycling(p<0.05).

• 박물관보존과학
• /
• 제6권
• /
• pp.55-66
• /
• 2005

도자기 복원재로서 사용되는 에폭시수지 3종( Epo-Tek 301, Araldite 103, Araldite 106 )과 안료 3종(분채, 파스텔, 콘테)을 실험재료로 선택하고, 이 재료들을 다양한 비율로 혼합한 시편들에서 색도변화율과 기공률, 그리고 침전률을 관찰하였다. 또한 저점도의 맑고 투명한 특징을 가진 Epo-tek 301에 4종의 백색안료와 6종의 충진제를 혼합한 시편들을 만들고 200시간동안 자외선을 조사하여 에폭시 수지의 산화를 관찰하였다. 그 결과, 파스텔은 Epo-tek 301과 혼합하면 화학적 변화가 심하였다. 분채와 콘테는 안료 발색력이 높았지만 다른 첨가물이 혼합되면 콘테의 발색력이 낮아졌다. Epo-tek 301은 소량의 첨가물에서는 몰림 현상이 나타났고 다량의 첨가물에는 포화상태가 되면서 끓어 넘쳤으며, AW 106은 점도가 높기 때문에 소량안료에는 발색이 잘 안되었지만 첨가물이 많을 때 오히려 발색이 잘되었다. AY 103은 첨가물의 양에 상관없이 규칙적이면서도 급격하지 않은 색도 변화를 나타내었다. 기공률은 [파스텔> 분채≒ 콘테], [Epo-tek 301< AY 103< AW 106]순서로, 침전률은 [분채> 콘테> 파스텔], [Epo-tek 301> AY 103> AW 106]순서로 나타났다. 황변도 측정에서 티타늄, 파스텔, 실리콘디옥사이드와 카올린은 황변이 잘되었고 분채, 콘테, 규조토와 수산화칼슘은 황변에 강했다.

• 보존과학회지
• /
• 제31권2호
• /
• pp.131-145
• /
• 2015

문화재 보존처리는 손상된 문화재의 수명을 연장하고 그 가치를 재조명하는 실질적 수단으로서 높이 평가 받고 있다. 그러나 보존처리 과정은 대부분 보존처리자의 경험과 기술에 의한 수작업에 의존하고 있어 이에 따르는 많은 시간과 노력이 요구된다. 최근에는 문화재의 재질 특성과 형상에 따라 보다 정확하고 손쉽게 보존처리를 진행할 수 있는 방법을 채용할 수 있게 되었다. 즉, 지금까지 수작업으로 이루어지는 보존처리과정을 3D 프린터를 이용하여 컴퓨터상에서 구현된 입체 형상 데이터를 실물로 출력하는 방법을 이용하는 것이다. 먼저 문화재의 결손 부분을 컴퓨터상의 데이터로 구축한 다음 3D 프린터로 출력하여 결손 부분을 손쉽게 성형 및 가공 과정을 거치는 것이다. 3D 프린터 적용결과 반복적인 출력 및 디지털데이터의 형태 및 수치 조정이 가능하였으며, 다양한 소재를 활용한 여러 가지 복원재료로 부터 시험출력을 통하여 문화재 복원의 완성도를 향상시킬 수 있었다. 본 연구에서 도자기 결손부분 복원을 위한 3D 프린터 적용 시험을 위하여 현대 재현품인 청자칠보무늬향로와 차륜식토기 2점을 인위적으로 파손시켰다. 복원결과 수작업에 비해 작업시간 단축 및 정확한 형태의 재현 등에서는 좋은 효과를 나타내었다. 반면 정밀한 접합 및 표면 질감을 생생하게 표현하기 위해서는 약간의 2차적인 수작업이 필요하였다.

• 한국결정성장학회지
• /
• 제25권1호
• /
• pp.20-26
• /
• 2015

세라믹 잉크젯 기술은 아트타일, 장식용 도자기 등에 이용되고 있으며, 원료의 효율이 높고 낮은 제작비용으로 다양한 이미지를 빠르고 정확하게 인쇄할 수 있다는 장점을 가지고 있다. 잉크젯 프린팅 타일에 나노세라믹안료를 적용하기 위해서는 안정적인 잉크분산성 확보가 필수적이다. 본 논문에서는 잉크젯 인쇄용 수계 pink-red 세라믹잉크의 특성을 보여주고 있다. $CaCr_{0.1}Sn_{0.8}SiO_5$ 안료는 고상법을 이용하여 합성하였고, 잉크 토출 시 잉크젯 헤드의 노즐 막힘을 방지하기 위해 어트리션밀을 이용하여 분쇄한 안료를 사용 하였다. 수계 세라믹잉크 제조 시 $CaCr_{0.1}Sn_{0.8}SiO_5$ 나노안료의 농도는 10 wt%로 고정하였고, sodium dodecyl sulfate(SDS)를 0.4 wt% 첨가 하였을 때 최적의 분산성을 가지는 것을 확인할 수 있었다. 또한 수계 세라믹 잉크의 원활한 토출을 위해 polyvinyl alcohol(PVA)을 0.18 wt% 첨가하여 점도 조절을 하였다. 제조된 pinkred 세라믹 잉크는 토출 시 $180{\mu}s$ 이후 구형의 단일액적을 형성 하는 것을 확인할 수 있었다.

• 대한치과기공학회지
• /
• 제37권3호
• /
• pp.131-144
• /
• 2015

Purpose: This study set out to propose plans for more efficient and effective clinical practice by investigating the current state of clinical practice in the field of dental technology and thus provide basic data to develop pre- and post-education programs for clinical practice. Methods: The subjects include dental technicians at dental technical laboratories that were appointed as the place of clinical practice by the Department of Dental Technology of G University. The survey period spanned from December 22, 2014 to January 20, 2015. Total 250 questionnaires were distributed to them, and 190(76.0%) were returned. After excluding 23 whose answers were uncertain or seemed to lack reliability, total 167(66.8%) were used in final analysis. Results: 1. The most frequent practice the student did during clinical practice was articulator attachment, which was followed by pin operation or model making, one's own task and practice, sand and crow sculpturing, burying, casting, and grinding. 2. In case of going through the entire process, porcelain had the most students at 39(23.4%), being followed by crown & bridge at 28(16.8%), clinical model at 23(13.8%), full denture at 17(10.2%), and partial denture at 17(10.2%) in the order. 3. Of the students, 59.8%(30.5% for reinforced basic practice; 29.3% for intensive practice education) said that intensive practice education should be reinforced in school; and 22.3% said that intensive theory and practice education was needed, which indicates that 82.6% voiced their opinion of reinforcing education around practice. 4. The students felt that they lacked diligence, passion, and theoretical knowledge somewhat and were relatively good at clinical adaptation and operational skills. Conclusion: The findings show that the students felt an absolute lack of practice education as the school education was focused on theory and national exams in the field of dental technology, thus raising a need to reinforce practice education. Of all the respondents, 62.9% said there was a need to improve the current education with a focus on jobs. In future, education of dental technology should work to bring up able dental technicians that can perform in clinical dental technology right after graduation by reinforcing job-based practice education.

• 대한치과기공학회지
• /
• 제36권4호
• /
• pp.277-296
• /
• 2014

Purpose: This study intends to set standard for organizing the curriculum of short-term dental technicians and the change of job environment, as well as the knowledge & training, by identifying the importance and actual job performance of dental technicians following job analysis in the university education of Dept. of Dental Laboratory Technology, and furthermore to foster junior executives to cope with modernization and globalization. Methods: The tools used in this study are based on the job analysis of research report suggested by National Health Personnel Licensing Examination Board(Lee Gyu-seon, 2011), and it consists of general characteristic 7 items. Every competence duty was measured through Likert 5 point gauging, and internal consistency through Cronbach's Alpha. The competence importance of entire questionnaire was .984 and its performance was .874, reflecting considerably high level, and in terms of each competence duty, high credibility was proved and high internal consistency was verified with competence importance ranging from the minimum .655 to the maximum .966 and its performance ranging from the minimum .677 to the maximum .993. Results: Competence importance and its performance in each duty on the job analysis of dental technicians were measured. In competence importance in each duty, the highest was "checking design order form"(average, 4.52), followed by "selling dental prosthesis"(average 4.49), "making removable orthodontic appliance"(average, 4.48), "open managing dental laboratory"(average, 4.46) in order. However, "making complete denture" was found the lowest(average, 4.23), with importance of all competence dutys was considerably high level. In the performance of its competence duty, "checking design order form"(average, 4.04) was found to be the most importance competence, followed by "making conservative restoration"(average, 4.00), "making porcelain"(average 3.98), "checking working cast"(average, 3.90) in order. However it was found out that "making fixed orthodontic appliance"(average, 3.12) was the lowest, and the importance of all competence dutys was quite high level. Conclusion: The duties of dental technicians consist of 13 kinds, in total, and it was found out that "checking design order form"(average, 4.52) was the most important in the competence importance and job performance. In particular, it was revealed that there was a great difference between the competence importance and its performance in the order of "selling dental prosthesis", "open managing dental laboratory", "making removable orthodontic appliance", "making CAD/CAM prosthesis", and then "making fixed orthodontic appliance".

• 대한치과보철학회지
• /
• 제39권5호
• /
• pp.463-476
• /
• 2001

Since the treatment of edentulous patients with osseointegrated implant was first introduced more than 30 years ago, implant therapy has become one of the most important dental treatment modalities today. Based on the previous experience and knowledge, $Br{\aa}nemark\;Novum^{(R)}$ protocol was introduced with the concept of simplifying surgical and prosthetic technique and reducing healing time recently. This protocol recommends the installation of three 5mm wide diameter futures in anterior mandible and the prefabricated titanium bars for superstructure fabrication. This study was designed to analyze the stress distribution at fixture and superstructure area according to changes of fixture number, diameter and superstructure materials. Four 3-dimensional finite element models were fabricated. Model 1 - 5 standard fixtures (13mm long and 3.75mm in diameter) & superstructure consisted of type IV gold alloy and resin Model 2- 3 wide diameter fixtures (13mm long and 5.0mm in diameter) & superstructure consisted of type IV gold alloy and resin Model 3-3 wide diameter fixtures (13mm long and 5.0mm in diameter) & superstructure consisted of titanium and resin Model 4-3 wide diameter fixtures (13mm long and 5.0mm in diameter) & superstructure consisted of titanium and porcelain A 150N occlusal force was applied on the 1st molar of each model in 3 directions - vertical($90^{\circ}$), horizontal($0^{\circ}$) and oblique($120^{\circ}$). After analyzing the stresses and displacements, following results were obtained. 1. There were no significant difference in stress distribution among experimental models. 2. Model 2, 3, 4 showed less amount of compressive stress than that of model 1. However, tensile stress was similar. 3. Veneer material with a high modulus of elasticity demonstrated less stress accumulation in the superstructure. Within the limites of this study, $Br{\aa}nemark\;Novum^{(R)}$ protocol demonstrated comparable biomechanical properties to conventional protocol.

• 대한치과보철학회지
• /
• 제38권4호
• /
• pp.446-460
• /
• 2000

All-ceramic restorations have had a more limited life expectancy than metal ceramic crowns be-cause of their lower strength. The relatively lower strength has limited the use of all-ceramic crowns to the areas where occlusal loads are lower Therefore many researches have been done to increase the strength of all-ceramic crowns. IPS Empress 2 is a new type of lithium disilicate glass-ceramic with enhanced physical characteristics which has been in use clinically since 1998. Previous researches reported that the flexural strength of all-ceramic material was greater than 300 MPa, and all-ceramic crowns can be used in staining or layering technique. The objective of this study was to investigate the influence of the thickness of IPS Empress 2 ceramic on fracture strength. Both staining technique and layering technique was investigated. Vita VMK was used as control. For all three groups, five specimens each of 0.8mm, 1.0mm, 1.4mm, 1.8mm, and 2.2mm thick-ness (a total of 75 specimens) were prepared. Control group : Vita VMK Porcelain specimens were prepared with dentine ceramic and liquid glazing was done. Group I : IPS Empress 2 were prepared with staining technique and stained twice and glazed once. Group II : IPS Empress 2 were prepared with layering technique and glazed after wash firing. The thickness and diameter of the specimen were measured and controlled after specimen preparation. Biaxial Flexure Test (ASTM Standard F394-78) was adopted as this test method produces results least affected by the edge condition of the specimens. Fracture strength was measured with Instron Universal Testing Machine. Conclusions are as follow : 1. The fracture strength was increase in order of control group, test group I, test group II. 2. Fracture strength of the group I (Empress 2 Staining) was 65.54 N in 0.8mm, 155.2 N in 1.0mm, 233.5 N in 1.4mm, 434.5 N in 1.8mm, and 600.1 N in 2.2mm. 3. Fracture strength of the group II (Empress 2 Layering) was 190.0 N in 0.8mm, 283.5 N in 1.0mm. 437.2 N in 1.4mm, 732.0 N in 1.8mm, and 1115.0 N in 2.2mm. 4. No statistical difference was found in flexural strengths according to thickness in a specified group(p>0.05).

• 한국조경학회지
• /
• 제18권1호
• /
• pp.1-8
• /
• 1990

서울시내 아파트 40가구를 대상으로 1986년과 1989년에 실내조경식물을 조사한 결과, 다음과 같다1. 1986년에 비해서 1989년에는 전제실내식물의 종류는 46%, 식물의 수는 68%가 증가되었으며, 가장 많이 재배되는 종류는 '86년에는 동양란 아프리칸 바이올렛, Scindapsus, 선인장, 군자란 '89년에는 동양란, 선인장, Chlorophytum, 군자란, Dracena순이었다. 2. 원예학적 분류방법에 의한 식물의 종류는 '86년, '89년 모두 관엽식물이 가장 많았다. 3. 초장에 따른 식물의 크기는 '86년에는 15~30cm가 제일 많았고, '89년에는 31~80cm가 가장 많았다. 4. 식재용기의 종류는 '86년과 '89년 모두 플라스틱이 가장 많았으며, 자기 분의 경우 '86년에 비해서 '89년에는 매우 증가되었다. 5.식물의 배치형태는 '86년과 '89년에 조사한 모든 아파트에서 마루에 그대로 놓아둔 floor group이 있었으며, 그 비율도 가장 높았고 선반의 경우 '86년에 비해서 '89년에는 매우 많이 이용되었다. 6. Terrarium의 경우 '86년에는 Fittonia와 선인장이 가장 많이 이용되는 소재였으나, '89년에는 Adianrum과 Maranta가 많이 이용되었다. 7. 식물이 가장 많이 배치되는 장소는 '86년, '89년 모두 베란다로 조사한 모두 가구에서 이용하고 있었다. 8.'86년에는 가구당 평균 16개를 보유하고 있었으나 '89년에는 평균 27개를 보유하고 있었다. 9.식물의 생육형태는 대체로 양호한 편이었으며, 실내조경식물의 재배관리에 대한 관심이 증가 하고있었다.