• Journal of Adhesion and Interface
• /
• v.17 no.4
• /
• pp.131-135
• /
• 2016

We investigated the specific gravity and mechanical property changes of solid-state extruded polypropylene (PP)/talc composites before and after orientation. The specific gravity of the composites increases with increasing the filler contents. The specific gravity of the oriented specimen containing filler in PP matrix is found to be much smaller than that of pre-specimen due to the formation of more micro-voids. It was found that the tensile properties of the composites are increased up to the talc content of 10 wt%, but after the contents exceeding 10 wt%, the tensile properties are decreased. For oriented specimens, the tensile strength of the composites showed monotonously decrease with increasing talc contents. When the contents of talc is 10 wt%, the theoretical values according to Halpin-Tsai equation are close to the experimental values but over 20 wt% of talc contents, the deviation of the experimental values from the theoretical prediction becomes higher. The maximum flexural strength and modulus were observed for PP/talc composites when the talc contents was 10 wt% for both pre-specimen and oriented specimen.

• Journal of Adhesion and Interface
• /
• v.14 no.4
• /
• pp.175-182
• /
• 2013

In this work, we aim to investigate the specific gravity, thermal, and mechanical property changes of solid-state extruded polypropylene (PP)/calcium carbonate composites before and after orientation. For this work, we prepared $PP/CaCO_3$ composites having two different sizes (OM-1 and OM-10). On increasing the filler content, the specific gravity of the composites increases. The specific gravity of the oriented specimen containing filler in PP matrix is found to be much smaller than that of pre-specimen due to the formation of more microvoids. The presence of microvoids in case of oriented composite specimen significantly affected the tensile and flexural properties of the composites. It was observed that the effect of orientation on both flexural strength and modulus is much stronger than the effect of filler contents, regardless of the filler particle size.

• Polymer(Korea)
• /
• v.36 no.1
• /
• pp.65-70
• /
• 2012

Glycidyl methacrylate (GMA) was used to introduce epoxy groups on the surface of polypropylene (PP) plate, used as a substrate, through plasma-induced graft copolymerization. Emulsion polymerization was applied for graft copolymerization of GMA and was compared with conventional solution polymerization to confirm its effect. Plasma treatment conditions under one atmospheric pressure were fixed as follows; the RF power of 200 W, the treatment time of 30 sec, the Ar gas flow rate of 6 LPM, and the exposure time of treated PP samples in air of 5 min. For graft-copolymerization, GMA concentration, reaction temperature, and reaction time was optimized to maximize the grafting degree of GMA. The maximum grafting degree of GMA was obtained at the condition of 12%-GMA concentration, $90^{\circ}C$ reaction temperature, and 5 hr-reaction time. Analysis results supported that the emulsion polymerization was more effective than the solution polymerization for grafting more GMAs on the surface of PP plate under the same reaction conditions.

• Journal of Adhesion and Interface
• /
• v.20 no.2
• /
• pp.66-70
• /
• 2019

The surface of hydrophobic polypropylene (PP) fibers (spun-bonded fabric) was treated by an atmospheric plasma treatment method. These pre-treated hydrophilic PP fabrics were dip-coated in the aqueous poly(N-vinyl pyrrolidone) (PVP) solution. PVP layers on the surface of PP fiber were crosslinked by an irradiation of electron beam. The thickness of PVP hydrogels coated on the surface was easily controlled by changing the concentration of PVP in coating solution. The stepwise surface treatment, PVP coating, and hydrogel formation via electron beam irradiation were analyzed by the measurement of contact angle, scanning electron microscopy, and optical microscopy.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.65-68
• /
• 2006

This study is aimed to investigate the strength variation of fire-damaged reinforced concrete column with polypropylene by non-destructive test. It is studied to infer the recovery degree of residual strength of fire-damaged concrete. For measuring the surface hardness of RC columns, Schmidt hammer test is used. Testing is performed four-times: before fire test, directly after fire test, after 30 days and after 4 months.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.9
• /
• pp.724-730
• /
• 2014

It is essential to control noise and vibration in various industrial fields. In the automobile industry, various plastics have been developed and replaced metallic materials in order to reduce mass and vibration effectively. In this study, we measured and analyzed the Young's moduli and the loss factors of Acrylonitrile butadiene styrene(ABS) and Polypropylene(PP). In order to solve the fundamental error to determine the two quantities, a loudspeaker was used instead of conventional electromagnetic devices to generate bending motion to the specimens and a laser vibrometer was also used in detection of vibration signal of the specimen. The measured Young's moduli and loss factors of the ABS specimen were nearly constant as the temperature($-10{\sim}60^{\circ}C$) was increased. The loss factor of PP specimen showed peak value at $20^{\circ}C$ and it means that there is glass transition for the PP specimen. Young's modulus of PP specimen was linearly decreased as the temperature was increased.

• Computers and Concrete
• /
• v.26 no.2
• /
• pp.115-125
• /
• 2020

To reduce the damage of concrete in fire, a new type of lightweight cinder aggregate concrete was developed due to the excellent fire resistance of cinder. To further enhance its fire resistance, Polypropylene (PP) Fibers which can enhance the fire resistance of concrete were also used in this type of concrete. However, the bond behavior of this new type of concrete after fire exposure is still unknown. To investigate its bond behavior, 185 specimens were heated up to 22, 200, 400, 600 or 800℃ for 2 h duration respectively, which is followed by subsequent compressive and tensile tests at room temperature. The concrete-rebar bond strength of C30 PP fiber-reinforced cinder concrete was subsequently investigated through pull-out tests after fire exposure. The microstructures of the PP fiber-reinforced cinder concrete and the status of the PP fibre at different temperature were inspected using an advanced scanning electron microscopy, aiming to understand the mechanism of the bonding deterioration under high temperature. The effects of rebar diameter and bond length on the bond strength of PP fiber-reinforced cinder concrete were investigated based on the test results. The bond-slip relation of PP fiber-reinforced cinder concrete after exposure at different temperature was derived based on the test results.

• Applied Chemistry for Engineering
• /
• v.7 no.3
• /
• pp.424-432
• /
• 1996

The fiber reinforced thermoplastic composites(FRTP) were prepared with polypropylene fiber(PPF) as matrix and vinylon(VF), Aramid(KF) or nylon fiber(PAF) as reinforcing materials using the integrated fiber mixing apparatus. The composite sheets were prepared by compression molding and their impact and morphological properties were characterized. VF/PP system showed the maximum value in Izod impact strength, while KF/PP system showed the maximum value in high rate impact properties. Ductility Index(DI) order was VF/PP>KF/PP>PAF/PP. A maximum DI for VF/PP, 2.43, was obtained when the weight fraction of VF was 20%. The optimum amount of the reinforcing organic fiber was found to be 20~30%. As a result, it is concluded that VF/PP system has better interfacial adhesion properties than either KF/PP or PAF/PP.

• Clean Technology
• /
• v.29 no.3
• /
• pp.185-192
• /
• 2023

This study was conducted to obtain basic process simulation data before conducting pyrolysis experiments for the development of a thermochemical conversion system by recirculation of heat carrier and gases thereby. In this study, polypropylene (PP) was used as a pyrolysis sample material as an alternative to waste plastics, and fluid sand was used as a heat transfer medium in the system. Manganese (Mn) was chosen as the catalyst for the pyrolysis experiment, and the catalyst pyrolysis was performed by impregnating it in the sand. The basic properties of PP were analyzed using a thermogravimetric analyzer (TGA), and liquid oil was generated through catalytic pyrolysis under a nitrogen atmosphere at 600℃. The carbon number distribution of the generated liquid oil was confirmed by GC/MS analysis. In this study, the effects of the presence and the amount of Mn loading on the yield of liquid oil and the distribution of hydrocarbons in the oil were investigated. When Mn/sand was used, the residue decreased and the oil yield increased compared to pyrolysis using sand alone. In addition, as the Mn loading increased, the ratio of C₆~C₉ range gasoline in the liquid oil gradually increased, and the distribution of diesel and heavy oil with more carbon atoms than C₁₀ in the oil decreased. In conclusion, it was found that using Mn as a catalyst and changing the amount of Mn could increase the yield of liquid oil and increase the gasoline ratio in the product.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.04a
• /
• pp.126-129
• /
• 2003

폴리프로필렌(PP) 필름사는 크게 스플리트사(split yam)는 슬리트사(slit yarn)로 구분된다. 이러한 PP 필름사의 제조공정은 필름압출와 연신공정이 연속적으로 이루어져 있으며 고도로 연신되고 가공되기 때문에 전형적인 멀티필라멘트사 제조공정과 비교하여 압출공정이 간단하고 소규모로도 가능하므로 경제적이라 할 수 있다[1-3]. 스플리트사는 슬리트사 제조공정에서 연신과정에 새로이 해섬장치를 부착하여 기계적으로 슬리트된 필름사를 일정한 기하학적 구조로 미세화하여 제조한다[2]. (중략)