• Fibers and Polymers
• /
• v.5 no.4
• /
• pp.264-269
• /
• 2004

The present paper deals with improvement in disperse dyeablility as well as imparting of cationic dyeablility to difficultly dyeable polypropylene by a melt blending technique. Isotactic polypropylene (PP) was blended with fibre grade polybutylene terephthalate (PBT), cationic dyeable polyethylene terephthalate (CDPET) and polystyrene (PS), individually. The resulting binary blends were spun and drawn into fibres at draw ratio 2, 2.5, and 3. The compatibility of blends, structural changes of fibres in terms of X-ray crystallinity, relative crystallinity, sonic modulus, birefringence and thermal stability were examined. The blended fibres were found to be disperse dyeable by the conventional method of high temperature and high pressure dyeing. And this dye ability increased with increase in the level of substitution. PP/CDPET blend also exhibited dyeablility with cationic dyes in addition to that with disperse dyes. The optimum level of blending was predicted keeping in view of tenacity and thermal stability of melt blend fibres. The wash fastness properties of the dyed fibres were found to be of high rate.

• Journal of Radiation Industry
• /
• v.9 no.2
• /
• pp.57-62
• /
• 2015

In this study, we fabricated effect of storage conditions on graft of polypropylene (PP) non-woven fabric induced by electron beam. The electron beam irradiations on PP non-woven fabric were carried out over a range of irradiation doses from 25 to 100 kGy to make free radicals on fabric surface. The radical measurement was established by electron spin resonance (ESR) for confirming the changes of the alkyl radical and peroxy radical according to effect of storage time, storage temperature and atmosphere. It was observed that the free radicals were increased with irradiation dose and decreased with storage time due to the continuous oxidation. However, the radical extinction was significantly delayed due to reduced mobility of radicals at extremely low temperature. The degree of graft based on the analysis of ESR was investigated. The conditions of graft reaction were set at a temperature: $60^{\circ}C$, reaction time: 6 hours and styrene monomer concentration: 20 wt%.

• Journal of Adhesion and Interface
• /
• v.15 no.1
• /
• pp.9-13
• /
• 2014

The purpose of this work is to investigate the specific gravity, thermal, and mechanical property changes of polypropylene (PP)/mica composites before and after solid-state extrusion. On increasing the filler content, the specific gravity of the composites increased. The specific gravity of the oriented specimen containing filler in PP matrix is found to be much smaller than that of pre-specimen due to the formation of more microvoids. The presence of microvoids in the case of oriented composite specimen significantly affected the tensile and flexural properties of the composites. Both flexural strength and modulus of the composites showed maxima when the mica contents was 10 wt%, regardless of the orientation via solid state extrusion.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2003.11a
• /
• pp.517-523
• /
• 2003

The physical properties of polypropylene (PP) membranes under the radiation field were investigated. To calculate radiation flux affecting to PP, it was used MCNP4A Code. The PP membrane and deoxygenation equipment were standardized to bar structure in order to calculate the phonton flux with MCNP4A Code. The change in the properties of the PP membrane to be used in deoxygenation equipment was rarely occurred during the usage work because the radiation level of reactor coolant water was very low level and The doses of radiation workers are very low. From the results, it was found that the Physical properties of PP membranes which used for nuclear power plant reactor coolant water disposal were not rarely changed under the simulated radiation field.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.108-111
• /
• 2004

The polypropylene(PP) fiber is poised as a low cost alternative for reinforcement in structural applications in comparison with other high performance fibers, such as the polyvinyl-alcohol(PVA), polyethylene, carbon and aramid fiber. The mechanical properties of the composite are strongly determined by the interfacial behavior of fiber and cementitious matrix. The crack bridging mechanism contribute to composite toughness from activation of the fiber-matrix interface where energy is dissipated through debonding of the interface and fiber pullout. In this study, therefore, the pullout behavior of PP fibers is investigated. Experimental work includes the investigation of the interfacial properties, and the composite property. The quantification of interfacial properties, the frictional bond is achieved through single fiber pullout test. A study on the effect of inclination angle on fiber pullout behavior is also conducted.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.10
• /
• pp.1881-1887
• /
• 2011

In this work the recyclable new polyethylene(PE) and polypropylene(PP), which are thermoplastic, have been investigated as the eco-friendly insulating candidates to replace the cross-linked polyethylene (XLPE). The temperature dependence of conductivities of these materials has been measured and its effects on electric field and space charge distribution in polymeric insulated power cable under temperature gradient have been calculated. It is shown that the sensitivity of conductivity to temperature change has more critical influence to determine the electric field distribution in the power cable than the absolute value of conductivity does and it can be said that the temperature dependence is one of most important factors for the power cable design.

• Journal of the Korean Applied Science and Technology
• /
• v.23 no.4
• /
• pp.362-367
• /
• 2006

This paper describes the experiments for investigating the effects of thermal stability of several commercial carpet mate materials. The melting point and thermal decomposition temperature was measured by means of a differential scanning calorimeter(DSC) in air condition. The DSC data and burning test results of nylon bulked continuous filament(N-BCF) yarn 100%, nylon(NY), polypropylene(PP), and a new material named polytrimethyleneterephthalate(PTT) were analysed to obtain the effect on their thermal stability. Conclusively, we observed that PTT and PP were approximately $380^{\circ}C$ and $240^{\circ}C$ to start the thermal decomposition, respectively. In other words, PTT is thermally the most stable material for carpet manufacturing.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.290-290
• /
• 2006

The toughening mechanisms of polypropylene (PP) containing 9.2 vol % of calcium carbonate ($CaCO_{3}$) nanoparticles were investigated using optical microscopy and transmission electron microscopy. Double-notch four-point bending (DN-4PB) Charpy impact specimens were utilized to study the fracture mechanism(s) responsible for the observed toughening effect. A detailed investigation reveals that the $CaCO_{3}$ nanoparticles act as stress concentrators to initiate massive crazes, followed by shear banding in PP matrix. These toughening mechanisms are responsible for the observed improved impact strength.

• Transactions of Materials Processing
• /
• v.13 no.4
• /
• pp.365-373
• /
• 2004

The sheet formability of single AA5182 sheets and sandwich sheets comprising of AA5182/polypropylene/AA5182 (AA/PP/AA) was studied. Rolling without lubrication and subsequent recrystallization annealing led to the formation of favorable ｛111｝//ND fiber textures in AA5182 sheets, which provided a higher plastic strain ratio of $R_m=1.5$. $R_m$ value of 1.58 was obtained in the AA/PP/Ah sandwich sheet sample. Furthermore, a proper combination of the sample direction of the upper and lower skin sheet gave rise to an optimization of the sheet formability of the sandwich sheets.

• Analytical Science and Technology
• /
• v.23 no.6
• /
• pp.615-618
• /
• 2010

An oxygen bomb combustion procedure were studied for determination of heavy metal in polymer materials such as polyvinyl chloride and polypropylene by ICP-AES. This method is proposed as a rapid and simple sample preparation for decomposition of polymer containing certified contents of the analytes by teflon coated oxygen bomb combustion using different absorbing solution. The recoveries of metal were found to be 30~102% from absorbed solution by ICP-AES method using polypropylene certified reference material(PP CRM-As, Ba, Cd, Hg, Pb, Zn). The recoveries of metal using PVC CRM(Cd, Hg, Pb) was found to be 45 ~101% with same procedures.