• Journal of the Korean institute of surface engineering
• /
• v.48 no.3
• /
• pp.87-92
• /
• 2015

Carbon thin films were deposited on STS 316L sheets by inductively coupled plasma enhanced magnetron sputtering with or without substrate bias voltage. Typical Raman spectrum for amorphous diamond-like carbon (DLC) was obtained, and the interfacial contact resistance (ICR) was measured to show its conductive nature. The electrochemical impedance spectroscopy (EIS) was used to investigate the corrosion mechanism of the carbon coating under the polymer electrolyte membrane fuel cell (PEMFC) condition. According to the pore-corrosion mechanism, the electrolyte penetrates the carbon coating through the pores and reacts with the substrate. As the substrate corrosion proceeds, the pore enlargement occurs and the surface area of the substrate exposed to the electrolyte. Applicability of the carbon coating for the PEMFC bipolar plate was evaluated by potentiodynamic polarization experiments. Finally, an adhesion problem was briefly considered.

• Journal of the Korean Electrochemical Society
• /
• v.14 no.2
• /
• pp.110-116
• /
• 2011

Ru black was used for cathode catalyst in polymer electrolyte membrane fuel cell which showed low performance at the initial test. However, it was observed that the performance of Ru black cathode was dramatically enhanced after certain kind of experiment compared with initial one. It might be due to an electrochemical treatment in which a voltage was applied to the Ru cathode for constant period time. When a constant potential of 0.1 V was applied to Ru cathode for 30 min, the fuel cell performance of Ru cathode showed the best results. In order to investigate the effect of electrochemical treatment on the performance enhancement, the characteristics of electrochemically treated Ru black was compared with that of Ru black which was reduced under $H_2$ atmosphere. From XRD results, it was turned out that Ru black was not completely converted to metallic Ru by electrochemical treatment, but it is sufficient to be one of reasons for the performance enhancement. According to the results of CO stripping voltammetry, it was observed that some Ru was removed from Ru electrode by electrochemical treatment which might have a bad effect on the fuel cell performance. The removal of some Ru from as-received Ru black by electrochemical treatment is also another reason for the enhancement of fuel cell performance.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.10
• /
• pp.1031-1037
• /
• 2010

This paper proposed lightweight aluminum bipolar plates as an alternative for conventional graphite bipolar plates in fuel cell systems used as a power source for small reconnaissance UAVs. Since bipolar plates occupy more than 80% of the total weight of the fuel cell system, lightweight aluminum bipolar plates can improve the overall payload and flight time of the fuel cell UAV. The aluminum and graphite bipolar plates were fabricated to compare the performance of each of them. A 15% higher performance per weight was obtained from aluminum bipolar plates than the graphite bipolar plates. Also, the performance of a single cell using aluminum bipolar plates was evaluated under various operating conditions.

• New & Renewable Energy
• /
• v.17 no.2
• /
• pp.50-58
• /
• 2021

We proposed an MEA development methodology that accurately measures intrinsic MEA performance while considering the uneven reaction environments formed inside a large-area BP. To facilitate measurement of the inherent MEA performance, we miniaturized the active area of the MEA to 3 cm², and prepared two MEAs with different ionomer contents of 0.65 and 0.80 (I/C). By simulating the operating conditions of a 100 cm² BP at the inlet (I), center (C), and outlet (O), the oxygen concentration and relative humidity were determined to be 20.7, 13.8, 11.7%, and 50, 66.1, and 70.1% respectively. We measured the performance and electrochemical analysis of the prepared MEAs under the three simulated conditions. Based on the results of statistical analysis of the evaluated MEA performance data, I/C 0.65 MEA had a higher average performance and lower performance deviation than I/C 0.80 MEA. Hence, it can be concluded that an I/C 0.65 MEA is a more effective MEA for large-area BP. Based on the above research process, we confirmed the effectiveness of the proposed MEA development methodology.

• Journal of Electrochemical Science and Technology
• /
• v.15 no.2
• /
• pp.253-260
• /
• 2024

Proton exchange membrane water electrolysis (PEMWE) is an efficient method for utilizing renewable energy sources such as wind and solar powers to produce green hydrogen. For PEMWE powered by renewable energy sources, its durability is a crucial factor in its performance since irregular and fluctuating characteristics of renewable energy sources, especially for wind power, can deteriorate the stability of PEMWE. Triangular voltage cycle is well able to simulate fluctuating wind power, but its effect on the durability has not been investigated extensively. In this study, the performance degradation of the PEMWE cell operated with the triangular voltage cycling was investigated at different ramping rates. The measured current responses during the cycling gradually decreased for both ramping rates, and I-V curve measurements before and after the cycling confirmed the degradation of the performances of PEMWE. For both measurements, the degradation rate was larger for 300 mV s^-1 than 30 mV s^-1, and they were determined as 0.36 and 1.26 mV h^-1 (at the current density of 2 A cm^-2) at the ramping rates of 30 and 300 mV s^-1, respectively. The comparison with other studies on triangular voltage cycling also indicate that an increase in the ramping rate accelerates the deterioration of the PEMWE performance. X-ray photoelectron spectroscopy and transmission electron microscopy results showed that the Ir catalyst was oxidized and did not dissolve during the voltage cycling. This study suggests that the ramping rate of the triangular voltage cycling is an important factor for the evaluation of the durability of PEMWE cells.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.2
• /
• pp.135-143
• /
• 2016

Biogas is a renewable fuel from anaerobic digestion of organic matters such as sewage sludge, manure and food waste. Raw biogas consists mainly of methane, carbon dioxide, hydrogen sulfide, and water. Biogas may also contain other impurities such as siloxanes, halogenated hydrocarbons, aromatic hydrocarbons. Efficient power technologies such as fuel cell demand ultra-low concentration of containments in the biogas feed, imposing stringent requirements on fuel purification technology. Biogas is upgraded from pressure swing adsorption after biogas purification process which consists of water, $H_2S$ and siloxane removal. A polymer electrolyte membrane fuel cell power plant is designed to operate on reformate produced from upgraded biogas by steam reformer.

• New & Renewable Energy
• /
• v.2 no.4 s.8
• /
• pp.46-55
• /
• 2006

본 연구는 불소그룹을 함유한 술폰화된 아릴렌에테르계 블록 공중합체 고분자 전해질막의 제조 및 연료전지 특성에 관한 것이다. 이러한 불소그룹을 함유한 술폰화된 아랄렌에테르계 블록 공중합체를 제조하기 위하여 양말단에 불소계 비닐기를 가지면서, 고분자 전환시 상온에서 술폰화 가능한 biphenyl계 단량체와 술폰화가 불가능한 sulfonyl계 단량체를 각각 합성하였다. Biphenyl계 단량체로 부터 올리고머를 합성한 후 sulfonyl계 단량체와 열적 고리화 부가중합을 하여 다양한 몰조성을 갖는 일련의 perfluorocyclobutane(PFCB)기를 포함하는 블록 공중합체를 제조하였다. 제조된 블록 공중합체를 상온에서 술폰화제인 chlorosulfonic acid(CSA)를 이용하여 후술폰화시켜 강산 이온기인 sulfonic acid를 biphenyl계 올리고머 부분에 선택적으로 도입하였다. 이렇게 제조된 술폰화된 고분자를 제막한 후 연료전지 특성을 Nafion-115와 비교하였다. 술폰화가 되는 올리고머 블록의 비율 증가에 따라 이온교환능력 (IEC)이 증가하였고 , 그에 따른 팽윤도 역시 증가하는 것을 보였다. 술폰화된 고분자들은 건조 및 습윤 상태에서도 기계적 강도가 우수하였다. 최적화된 술폰화 블록 고분자(S-2) 를 대상으로 membrane electrolyte assembly(MEA) 를 제조하여 연료전지 초기성능을 측정한 결과 Nafion-112와 유사한 전기화학적 성능을 나타내었다.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.4
• /
• pp.288-294
• /
• 2013

This gas analysis data come from the hydrogen which is produced by proton exchange membrane. Main impurities of hydrogen are methane, oxygen, nitrogen, carbon monoxide, and carbon dioxide. The concentration of impurities is ranged between 0.0191 to $315{\mu}mol/mol$ for each impurity. Methane contamination is believed from the electrode reaction between carbon doped electrode and produced hydrogen. Nitrogen contamination should take place the sampling process error, not from PEM hydrogen Production system.

• Polymer(Korea)
• /
• v.34 no.2
• /
• pp.137-143
• /
• 2010

A series of partially fluorinated, sulfonated poly(biphenylene-co-sulfone)ether containing perfluorocyclobutane(PFCB) groups were prepared for fuel cell applications through three synthetic steps: synthesis of trifluorovinylether-terminated monomers, thermal cycloaddition and post-sulfonation. Two kinds of trifluorovinylether-terminated monomers were synthesized and statistically copolymerized via thermal cycloaddition to obtain a series of polymers containing 20-60 mol% of biphenyl units(PBS-X). The post-sulfonation of PBS-X was carried out using chlorosulfonic acid(CSA) to obtain copolymers with various sulfonation levels(SPBS-X). All the synthesized compounds, monomers and polymers were characterized by $^1H$-NMR, $^{19}F$-NMR and FT-IR. It was confirmed that the ion exchange capacity(IEC), water uptake and ion conductivity of SPBS-X increased with the increment of sulfonated biphenyl units. Particularly, SPBS-60 showed higher ion conductivity compared to Nafion$^{(R)}$-115 at 25~80 $^{\circ}C$.

• Journal of the Korean Society for Heat Treatment
• /
• v.27 no.4
• /
• pp.169-174
• /
• 2014

The effect of varying amounts of graphite and $TiB_2$ on the electrical conductivity of composite bipolar plates was systematically studied. In this study, Titanium diboride ($TiB_2$) which has a high electrical conductivity, was selected as a filler and a additive material instead of conventional graphite. For proper distribution of the filler and matrix materials, ball milling using alumina balls was conducted for 1h, and then the hot press method was applied for the preparation of composite samples. The results showed a rapid increase in the electrical conductivity of composite bipolar plates at the critical filler content. However, $TiB_2$ and graphite composite bipolar plates showed similar increases in the electrical conductivity even though $TiB_2$ has a higher electrical conductivity than graphite. In addition, it was also found that a small addition of $TiB_2$ to graphite filler could be very effective for increasing the electrical conductivity and flexural strength of the composite bipolar plate.