• 한국인쇄학회지
• /
• 제16권3호
• /
• pp.43-60
• /
• 1998

The photosensitive properties and spectroscopic characteristics in the organic photoconductor(OPC) with carrier generation layer(CGL) of poly(vinylbutyral)(PVB) and polycarbonate(PC) doped with titanyl phthalocyanine(TiOPc) were investigated. The change of crystal structure of TiOPc dispersed with PVB and PC was shown by UV-visible reflective spectrum and FT-IR spectrum and mainly caused by the difference of solubility of solvent and the interaction between TiOPc and binder. The particle size of TiOPc dispersed with PVB measured by SEM was smaller than in PC. The crystal structure of TiOPc dispersed with PVB was amorphous type and in PC was $\alpha$type. It was found that the photosensitive properties of OPC were dependent on the change of absorbance and ionization potential of TiOPc occurred from the difference of crystal structure. In this work, the photosensitivity of OPC of TiOPc dispersed with PVB was better than PC due to the crystal type and the smaller particle size.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2003년도 학술발표논문집
• /
• pp.379-382
• /
• 2003

In this study, methyl methacrylate (MMA)- modified unsaturated polyester mortar, in which the MMA was added to the unsaturated polyester resin, was developed for improving the early-age strength and the workability of the conventional polymer concrete, binder of which was the unsaturated polyester resin. Then the strength properties of the MMA-modified unsaturated polyester mortar were surveyed. The experimental results showed that early-age strength was greater when the MMA contents were increased in the range of $20{\sim}40%$, but the strength rather showed a tendency of decrease when the MMA contents was 50%.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.289-292
• /
• 2006

The purpose of this study was to evaluate a performance of latex-modified repair material applied to the substrate concrete. The experimental variables were latex-cement ratios (5, 10, 15%), polymer(0.5%, 1%) and admixtures. The flow, air content, compressive strength, flexural strength were tested. Test results showed that compressive and flexural strength decreased by adding hydroxyethyl cellulose and increasing water-binder ratio. The compressive and flexural strength were increased when addition of defoamer.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.711-714
• /
• 2005

This paper focused on development of geopolymer for wood wool ceramic board. Geopolymer can substitude ordinary portland cement and its accelerator of wood wool cement board as inorganic polymer. In this study, what we would obtain geopolymer's properties such as initial setting time(KS L 5108), flow(KS L 5102) and compressive strength of 3days aged(KS L 5105), was less than 1 hour, more than $110\%$, more than 40Mpa. Geopolymer have three essential materials called filler, hardener and geopolymer liquor. So, We applied filler by quartz, hardener by blast furnace slag powder, metakaoline and fly ash, geopolymer liquor by NaOH, KOH and sodium silicate solution. As result of this experiment, what we could obtain best fitted geopolymer's properties such as initial setting time, flow and compressive strength of 3days aged, was 45min, $116\%$ and 43.6Mpa. This result can be applicable to commercial wood wool ceramic board.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 추계 학술논문 발표대회
• /
• pp.253-254
• /
• 2011

The purpose of this study is to investigate chloride ion adsoption property of cement mortar using nitrite type hydrocalumite(calumite) with self-corrosion inhibition function. Superior corrosion inhibition function of the VA/E/MMA-modified mortars with calumite was ascertained from accelerated corrosion test in the previous study. In this study, VA/E/MMA-modified mortars with calumite were prepared with calumite contents of 0, 5, 10% and polymer-binder ratio of 0, 10%, and tested for chloride ion adsorption to make it clear how calumite gives self-corrosion inhibition function to cement mortar. As a result, chloride ion adsorption property of VA/E/MMA-modified mortars with calumite was improved by increasing calumite contents compared to unmodified mortar regardless of using VA/E/MMA terpolymer powder or not.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.688-693
• /
• 2003

The PSP technique has been used to measure pressure distribution on a model surface quantitatively. The objective of this study is to develop PSP technique which can be applied to low-speed flows. Four different PSP formulations including two porphyrins (PtOEP and PtTFPP) and two polymers (Poly(TMSP) and RTV-118) were tested and the performance of each combination was checked. In the static calibration, the luminescent intensity of the PSP coatings was measured from 0kPa to 11kPa with 0.5, 1, 2kPa increments. Among 4 PSP formulations tested, the combination of PtOEP and RTV-118 shows the best performance. The PSP technique was applied to an oblique impinging jet to measure the pressure field distribution on the impinging plate.

• 한국응용과학기술학회지
• /
• 제27권2호
• /
• pp.216-221
• /
• 2010

Polyvinyl acetate (PVAc) prepared by emulsion polymerization has broad applications for additive such as paint binder, adhesive for wood and paper due to its low glass transition temperature which help to plasticize substrate resins. Since emulsion polymerization has a disadvantage that surfactant and ionic initiator degrade properties of the product polymer, poly (vinyl acetate-eo-ethyl acrylate) (VAc-EA) was synthesized using potassium persulfate as catalyst and polyvinylalcohol (PVA) as protective colloid to prevent the degradation. The copolymer latex product was internally plasticized and has enhanced adhesion, water resistance during VAc-EA emulsion polymerization. No coagulation and complete conversion occur with the reactant mixture of 10 mmol/L potassium persulfate, 10 mmol/L poly ( vinyl alcohol) (PVA 17). As the concentrations of PVA increase, the viscosity becomes increase.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 초전도 자성체
• /
• pp.37-40
• /
• 2002

Superconductor wire fabricated by electrophoresis showed its critical current density depended on parameters such as applied voltage and deposition time. Substrate and suspension solutions. and its properties are also important parameters. When same optimal parameter and condition was used, deposition density of superconductor film affect directly its critical current density. In this study, therefore, electrophoretic deposition technique was utilized for a densification of YBCO superconducting wire, and researches on electrophoretic suspension solutions and additive were experimentally performed for an improvement of the critical current density of fabricated electrophoretically superconducting wire. The samples fabricated in the solution with the additive, 8 vol.% of 1% PEG(1000), showed the highest critical current density.

• 대한조선학회논문집
• /
• 제41권1호
• /
• pp.82-87
• /
• 2004

The purpose of this paper is to obtain the data for manufacturing of microbe carriers as a method of FRP waste recycling technology. Since FRP waste is polymer, the experiment of the thermogravity analyzing was carried out to find thermal behavior. After that, microbe carriers were prepared from waste FRP powder, which had been decomposed, milled, and mixed with clay as a binder and CaCO3 as a flux and a loaming agent, respectively. finally it was made by filing of the sample up to 1,05$0^{\circ}C$. It was investigated how the variation of the additives and firing temperature effect apparent density, water absorption and micro structure.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2019년도 춘계 학술논문 발표대회
• /
• pp.116-117
• /
• 2019

3D printing technology can be applied to various industries, and is trapped by major technologies that change existing manufacturing processes. 3D printing materials must satisfy designability, economy and productivity, and building materials are required to have strength and economy secured technology. 3D printing technology of construction field can be divided into structural materials and internal and external materials, and is mainly done by extruding and adapting. Particularly when it is applied as an exterior materials, it is mainly applied to an unstructured exterior materials and high accuracy is required. The exterior materials can be used as a cement composite materials, it is suitable also for a lamination type, and the role of a cement base composite material is important. In this research, we developed a cementitious base binder applicable as a 3D printing exterior materials, confirmed high temperature strength characteristics for application as an exterior materials of buildings and confirmed its possibility.