• Journal of Welding and Joining
• /
• 제25권2호
• /
• pp.43-48
• /
• 2007

Laser Transmission Joining (LTJ) of plastics is a process in which light of suitable wavelength is transmitted through a transparent substrate that is in contact with an absorbing one. In this paper, LTJ is investigated by preliminary experiments from the viewpoint of mechanical engineering. To understand transmitting characteristics of each polymer substrate, transmission rate, reflection rate and absorption coefficient of polymer are measured by using a laser power-meter. Characteristics of joining in the spot welding and seam welding are investigated by measuring the fracture load. Fracture load increases in accordance to the laser power and irradiation time. However, when the laser power is over 60W and irradiation time over 4seconds, fracture load decreases. This phenomenon is probably due to heat-softening of materials. Besides, cavities are generated at a joint by evaporation of water molecules, which can be suppressed by introduction of a gap between two substrates.

• 한국레이저가공학회지
• /
• 제15권2호
• /
• pp.15-20
• /
• 2012

A novel joining technology was developed to compensate the camber in polymers. The preheating laser beam circulates on the joining location and the accumulated heat serves to increase the flexibility of neighboring polymers. The temperature rises up to the glass transient temperature of the polymers and continually loading spring force closes the gap of camber. The irradiated laser was 808nm central wavelength and the power varied between 2Watt and 5Watt. The laps were adjusted between 3 and 10 and the optimum process parameters were 3Watt and 5 laps for the specific application. An FEM analysis was introduced to understand the mechanism of joining by the transient temperature distribution on the polymers. Thermocouples experiments were also tried to correlate the numerical analysis results and it showed the trend of heat accumulation in experiments.

• 마이크로전자및패키징학회지
• /
• 제28권2호
• /
• pp.89-94
• /
• 2021

최근 플렉시블 기기의 상용화를 위하여 기계적 신뢰성 연구가 활발히 진행되고 있으며 이를 고려하여 신뢰성 높은 다양한 접합부의 구현이 중요하다. 기기의 많은 부피를 차지하는 고분자 기판 또는 필름을 접합할 때에는 재료의 약한 내열성으로 접합공정 중 열 손상이 발생할 수 있으므로 신뢰성을 확보를 위해 상온 접합공정이 필요하다는 제약이 있다. 기존의 기판 접합을 위해 사용되는 에폭시 또한 고온 경화가 요구되는 경우가 많고, 특히 경화 접합 후 에폭시는 접합부 유연성 및 피로 내구성에서 한계를 보인다. 이를 해결하기 위하여 접착제 사용이 없는 저온 접합 공정의 개발이 필요한 상황이다. 본 연구에서는 마이크로파에 의한 탄소나노튜브 가열을 이용한 고분자 기판의 저온 접합공정을 개발하였다. PET 고분자 기판에 다중벽 탄소나노튜브 (MWNT)를 박막 코팅한 뒤 이를 마이크로파로 국부 가열함으로써 접합 기판 전체는 저온을 유지하며 CNT-PET 기계적 얽힘을 유도하는 방식이다. PET/CNT/PET 접합시편에 600 Watt 출력의 마이크로파를 10초간 조사함으로써 유연기판 접합에 성공하였고 매우 얇은 CNT 접합부를 구현하였다. 접합 시편의 기계적 신뢰성을 평가하기 위해 중첩 전단 강도 시험, 삼점 굽힘 시험, 반복 굽힘 시험을 수행하였으며 각 시험으로부터 우수한 접합강도, 유연성, 굽힘 내구성이 확인되었다.

• 마이크로전자및패키징학회지
• /
• 제29권2호
• /
• pp.113-119
• /
• 2022

플렉서블, 웨어러블 디바이스 등을 포함한 차세대 전자 기기의 기계적 신뢰성 향상을 위하여 다양한 유연 접합부에서 높은 수준의 기계적 신뢰성이 요구되고 있다. 기존 고분자 기판 접합을 위한 에폭시 등의 유기 접착소재는 접합부 두께 증가가 필연적이며, 반복 변형, 고온 경화에 의한 열기계적 파손 문제를 수반한다. 따라서 유연 접합을 위해서 접합부 두께를 최소화하고 열 손상을 방지하기 위한 저온 접합 공정 개발이 요구된다. 본 연구에서는 플렉서블 기판의 유연, 강건, 저 열 손상 접합이 가능한 플렉서블 레이저 투과 용접(flexible laser transmission welding, f-LTW)를 개발하였다. 유연 기판 위 탄소나노튜브(carbon nanotube, CNT)를 박막 코팅하여 접합부 두께를 줄였으며, CNT 분산 빔 레이저 가열을 통한 고분자 기판 표면의 국부적 용융 접합 공정이 개발되었다. 짧은 접합 공정 시간과 기판의 열 손상을 최소화하는 레이저 공정 조건을 구축하였으며 고분자 기판과 CNT 접합 형성 메커니즘을 분석하였다. 또한 접합부의 강건성 및 유연성 평가를 위해 인장강도 시험, 박리 시험과 반복 굽힘 시험을 진행하였다.

• Journal of Welding and Joining
• /
• 제23권5호
• /
• pp.55-60
• /
• 2005

A precise bonding technique, transmission laser bonding using energy transfer, for polymer micro devices is presented. The irradiated IR laser beam passes through the transparent part and absorbed on the opaque part. The absorbed energy is converted into heat and bonding takes place. In order to optimize the bonding quality, the temperature profile on the interface must be obtained. Using optical measurements of the both plates, the absorbed energy can be calculated. At the wavelength of 1100nm $87.5\%$ of incident laser energy was used for bonding process from the calculation. A heat transfer model was applied for obtaining the transient temperature profile. It was found that with the power of 29.5 mW, the interface begins to melt and bond each other in 3 sec and it is in a good agreement with experiment results. The transmission IR laser bonding has a potential in the local precise bonding in MEMS or Lab-on-a-chip applications.

• 한국정밀공학회지
• /
• 제9권3호
• /
• pp.110-116
• /
• 1992

Electromgnetic joining of aluminum alloy tubes to high toughness polyurethane rubber cores is studied in order to estimate the joining strength and to analyze the effect of the process variables. The equation which can estimate the joining strength is proposed under considering the elastic recovery of the polyurethane core and the radial shrinkage of the core by pulling it axially. The obtained results are as follows : 1) The joining strength is mainly dependent on the magnitude of residual elastic strain of the polyurethane core. 2) The radial shrinkage (residual strain reduction) of the core during the axial pulling causes the joining strength to decrease severely. The equation for the reduced axial strength is proposed and it is found that the estimated values agree well with experimental results. 3) The magnitude of radial shrinkage could be reduced for the smaller value of ratio l/r. 4) The joining strength in metal/polymer joining increases as the friction coefficient increases. But its effect of friction coefficient is insignificant in comparison with the case of metal/metal joining.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1997년도 특별강연 및 춘계학술발표 개요집
• /
• pp.112-115
• /
• 1997

• Journal of Welding and Joining
• /
• 제33권2호
• /
• pp.78-84
• /
• 2015

Self-piercing rivet(SPR) is mechanical joining methods and which can be joining dissimilar materials. Unlike conventional riveting, SPR also needs no pre-drilled holes. During plastically deformation, SPR pierces upper sheet and joins it to under sheet. SPR has been mainly applied to the joining the automobile body and some materials, such as glass fiber reinforced polymer and aluminum alloy, which represent the sheet-formed materials for lightweight automobile. Glass fiber reinforced plastic(GFRP) has been considered as a partial application of the automobile body which is lighter than steels and stronger than aluminium alloys. It is needed SPR to join Al alloy sheets and GFRP ones. In this paper, in order to design the rivet and anvil, which are suitable for GFRP, the joinability was examined through simulations of SPR joining between GFRP and Al alloy sheets. For this study, AutoCAD was used for the modeling and the simulated using commercial FEM code DEFORM-2D. The simulated results for SPR process joining between GFRP and Al alloys were confirmed by the same conditions as experimental trials.

• Journal of Welding and Joining
• /
• 제32권4호
• /
• pp.20-25
• /
• 2014

Laser heat source was applied on 3D poly urethane model built by 3D printer and cellulous acetate for joining. A diode laser with 808nm wavelength was transmitted through the 3D model and applied on the boundary of ABS/Acetate and 3D poly urethane model. Based on the experimental result, the ABS and 3D built poly-urethane polymers was successfully joined, but the mechanical strength was not enough at the joining boundaries in the range of 6watt to 8watt of laser heat source. However, biodegradable acetate was successfully joined without damaging the 3D built model and mechanical strength was properly achieved. The optimum laser power was found between 5watt and 8watt with scanning speed of 500mm/min, 700mm/min and 1,000mm/min. Based on the SEM analysis the filling mechanism was that the applied pressure on 3D built model squeezed the fluidic thermoplastics, ABS and acetate, into the structure of 3D model. Therefore soundness of joining was strongly depending on the viscosity of thermoplastics in polymers. The developed laser process is expected to increase productivity and minimize the cost for the final products.

• Journal of Welding and Joining
• /
• 제28권3호
• /
• pp.42-48
• /
• 2010

Polycarbonate (PC) and Acrylonitrile Butadiene Styrene (ABS) were welded by a combination of a diode laser and a CNC machining center. Laser beam delivered through the transparent PC and was absorbed in an opaque ABS. Polymers were melted and joined by absorbed and conducted heat. Experiments were carried out by varying working distance from 44mm to 50mm for the focus spot diameter control, laser input power from 10W to 25W, and scanning speed from 100 to 400mm/min. The weld bead and cross-section were analyzed for weld quality, and tensile results were presented through the joint force measurement. With focus distance at 48mm, laser power with 20W, and welding speed at 300mm/min, experimental results showed the best welding quality which bead size was measured to be 3.75mm. The shear strength at the given condition was $22.8N/mm^2$. Considering tensile strength of ABS is $43N/mm^2$, shear strength was sufficient to hold two materials. A single process was possible in a CNC machining system, surface processing, hole machining and welding. As a result, the process cycle time was reduced to 25%. Compared to a typical process, specimens were fabricated in a single process, with high precision.