• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.456-459
• /
• 2000

Thin films of vanadium oxide(V$O_x$) have been deposited by r.f. magnetron sputtering from $V_2$$O_5$ prget in gas mixture of argon and oxygen. Crystal structure, surface morphology, chemical composition and bonding properties of films in-situ annealed in $O_2$ ambient with various heat-treatment conditions are characterized through XRD, SEM, AES, RBS and FTIR measurements. The filrns annealed below 200 $^{\circ}C$are amorphous, and those annealed above 30$0^{\circ}C$ are polycrystalline. The growth of grains and the transition of vanadium oxide into the higher oxide have been obsenred with increasing the annealing temperature and time. The increase of O/V ratio with increasing the annealing temperature and time is attributed to the diffusion of oxygen and the partial filling of oxygen vacancies. It is observed that the oxygen atoms located on the V-0 plane of $V_2$$O_5$ layer participate more readily in the oxidation process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.471-474
• /
• 2000

A flat type microgas sensor was fabricated on the p-type silicon wafer with low stress S $i_3$ $N_4$, whose thickness is 2${\mu}{\textrm}{m}$ using MEMS technology and its characteristics were investigated. W $O_3$thin film as a sensing material for detection of N $O_2$gas was deposited using a tungsten target by sputtering method, followed by thermal oxidation at several temperatures (40$0^{\circ}C$~$600^{\circ}C$) for one hour. N $O_2$gas sensitivities were investigated for the W $O_3$thin films with different annealing temperatures. The highest sensitivity when operating at 20$0^{\circ}C$ was obtained for the samples annealed at $600^{\circ}C$. As the results of XRD analysis, the annealed samples had polycrystalline phase mixed with triclinic and orthorhombic structures. The sample exhibit higher sensitivity when the system has less triclinic structure. The sensitivities, $R_{gas}$ $R_{air}$ operating at 20$0^{\circ}C$ to 5 ppm N $O_2$of the sample annealed at $600^{\circ}C$ were approximately 90. 90.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.12-13
• /
• 2006

Ferroelectric Cerium-substituted $Bi_4Ti_3O_{12}$ thin films with a thickness of 200 nm were deposited using the liquid delivery metal organic chemical vapor deposition process onto a Pt(111)/Ti/$SiO_2$/Si(100) substrate. At annealing temperature above $600^{\circ}C$, the BCT thin films became crystallized and exhibited a polycrystalline structure. The BCT thin film annealed at $720^{\circ}C$ showed a large remanent polarization ($2P_r$) of $44.56\;{\mu}C/cm^2$ at an applied voltage of 5V. The BCT thin film exhibits a good fatigue resistance up to $1{\times}10^{11}$ switching cycles at a frequency of 1 MHz with applied electric field of ${\pm}5\;V$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.10
• /
• pp.884-889
• /
• 2009

Recently, the control of size, morphology and dimensionality in inorganic materials has been rapidly developed into a promising field in materials chemistry. 3D nanostructured flower-like ZnO architecture with different size and shapes have been simply synthesized by hydrothermal process, using zinc acetate and ammonium hydroxide as reactants. In this study, the ZnO thin-films were deposited by RF magnetron sputtering in other to get high adhesion and uniformity of 3D nanostructured flower-like ZnO architecture on a $SiO_2$ substrate. The XRD patterns identified that the obtained the nanocrystallized ZnO architecture exhibited a wurtzite structure. SEM images illustrated that the flower-like ZnO bundles consisted of flower-like or chestnut bur, which were characterized by polycrystalline and (002) preferential orientation.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.35 no.8
• /
• pp.177-184
• /
• 2019

Recently, electric power usages and peak loads from buildings are increasing due to higher outdoor air temperatures and/or abnormal climate during the summer period. As one of the eco-friendly measures, a renewable energy system has been received much attention. Particularly, interest on a photovoltaic (PV) system using solar energy has been rapidly increasing in a building sector due to its broad applicability. In using the PV system, one of important factors is the PV efficiency. The normal PV efficiency is determined based on the STC(Standard Test Condition) and the NOCT(Nominal Operating Cell Temperature) performance test. However, the actual PV efficiency is affected by the temperature change at the module surface. Especially, higher module temperatures generally reduce the PV efficiency, and it leads to less power generation from the PV system. Therefore, the analysis of the relation between the module temperature and PV efficiency is required to evaluate the PV performance during the summer period. This study investigates existing algorithms for calculating module surface temperatures and analyzes resultant errors with the algorithms by comparing the measured module temperatures.

• Korean Journal of Metals and Materials
• /
• v.48 no.4
• /
• pp.353-356
• /
• 2010

InSb thin films with a thickness of approximately 300 nm were prepared using single- and double-source vacuum evaporation methods and their structures and properties were investigated in terms of a heat treatment procedure. The double-source InSb films, prepared by the alternate stacking of In and Sb, were polycrystalline in structure and included small amounts of unreacted In and Sb phases. After annealing at elevated temperatures below the melting point of InSb (525$^{\circ}C$), the films changed into the InSb phase and were found to contain small amounts of unreacted In. The formation capability of the InSb compound was slightly lower for multilayer films than for single-layer films. The electrical and galvanomagnetic properties were found to be strongly related to the microstructures of the films. The maximum value of the Hall mobility and the magnetoresistance were determined to be $4.3{\times}10^3cm^2$/Vs and 70%, respectively, for the single-layer films, while these values for the alternately stacked films were respectively $2.9{\times}10^3cm^2$/Vs and 29% for the $[Sb(2.5)/In(2.5)]_{60}$ films, and $3.1{\times}10^3cm^2$/Vs and 10% for the $[Sb(150)/In(150)]_1$ films.

• Journal of Ceramic Processing Research
• /
• v.20 no.6
• /
• pp.603-608
• /
• 2019

In this study, the multilayered thin films of (Ba,Sr)TiO3/K(Ta,Nb)O3 were fabricated by the sol-gel and spin coating methods, and their structural and electrical properties were investigated. The specimen showed polycrystalline X-ray diffraction (XRD) characteristics with a tetragonal structure. The average grain size and film thickness for one coating were about 30~40nm and 60nm, respectively. The phase transition temperature of specimen was lower than 10 ℃. The dielectric constant and loss at 20 ℃ of the specimen coated six times were 1,231 and 0.69, respectively. The rate of change in dielectric constant at an applied direct current (DC) voltage of the six times coated thin films was 17.3%/V. The electrocaloric effect was the highest around the temperature at which the remanent polarization rapidly changed. When an electric field of 660kV/cm was applied to the triply coated thin films, the highest electrocaloric property of 4.41 ℃ was observed.

• Journal of Ceramic Processing Research
• /
• v.13 no.spc2
• /
• pp.394-397
• /
• 2012

In this work, we studied the influence of the dopant elements concentration on the properties of SnO2 thin films deposited by pulsed laser deposition. X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), Hall effect measurement and UV-Vis studies were performed to characterize the deposited films. XRD results showed that the films had polycrystalline nature with tetragonal rutile structure. FE-SEM micrographs revealed that the as deposited films composed of dense microstructures with uniform grain size distribution. All the films show n-type conduction and the best transparent conductive oxide (TCO) performance was obtained on 6 wt% Sb2O5 doped SnO2 film prepared at pO2 of 60mtorr and Ts of 500 ℃. Its resitivity, optical transmittance, figure of merit are 7.8 × 10-4 Ω cm, 85% and 1.2 × 10-2 Ω-1, respectively.

• Korean Journal of Materials Research
• /
• v.22 no.12
• /
• pp.711-716
• /
• 2012

Tungsten bronze structure $Sr_{1-x}Ba_xNb_2O_6$ (SBN) single crystals were grown primarily using the Czochralski method, in which several difficulties were encountered: striation formation and diameter control. Striation formation occurred mainly because of crystal rotation in an asymmetric thermal field and unsteady melt convection driven by thermal buoyancy forces. To optimize the growth conditions, bulk SBN crystals were grown in a furnace with resistance heating elements. The zone of $O_2$ atmosphere for crystal growth is 9.0 cm and the difference of temperature between the melt and the top is $70^{\circ}C$. According to the growth conditions of the rotation rate, grown SBN became either polycrystalline or composed of single crystals. In the case of as-grown $Sr_{1-x}Ba_xNb_2O_6$ (x = 0.4; 60SBN) single crystals, the color of the crystals was transparent yellowish and the growth axis was the c-axis. The facets of the crystals were of various shapes. The length and diameter of the single crystals was 50~70 mm and 5~10 mm, respectively. Tungsten bronze SBN growth is affected by the temperature profile and the atmosphere of the growing zone. The thermal expansion coefficients on heating and on cooling of the grown SBN single crystals were not matched. These coefficients were thought to influence the phase transition phenomena of SBN.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05b
• /
• pp.70-73
• /
• 2002

Thin films of vanadium oxide($VO_{x}$) have been deposited by r.f. magnetron sputtering from $V_{2}O_{5}$ target in gas mixture of argon and oxygen. The oxygen/(oxygen+argon) partial pressure ratio of 0% and 8% is adopted. Crystal structure, chemical composition, molecular structure and optical properties of films sputter-deposited under different oxygen gas pressures and in-situ annealed in vacuum at $400^{\circ}C$ for 1h and 4h are characterized through XRD. RBS, FTlR and optical absorption measurements. The films as-deposited are amorphous and those annealed for time longer than 4h are polycrystalline. $V_{2}O_{5}$ and lower oxides co-exist in sputter-deposited films and as the oxygen partial pressure is increased the films become more stoichiometric $V_{2}O_{5}$. When annealed at $400^{\circ}C$, the as-deposited films are reduced to a lower oxide. It is observed that the oxygen atoms located on the V-O plane of $V_{2}O_{5}$ layer participate more readily in the oxidation and reduction process. The optical transmission of the films annealed in vacuum decreases considerably than the as-deposited films and the optical absorption of all the films increases rapidly between 400 and 550nm.