• Korean Journal of Materials Research
• /
• v.9 no.11
• /
• pp.1075-1082
• /
• 1999

Composite air electrodes of 50/50 vol% LSM- YSZ where LSM =$\textrm{La}_{1-x}\textrm{Sr}_{x}\textrm{MnO}_{3}$(0$\leq$x$\leq$0.5) were prepared by colloidal deposition technique. The electrodes were then examined by scanning electron microscopy (SEM) and studied by ac impedance spectroscopy in order to improve the performance of a solid oxide fuel cell (SOFC). Reproducible impedance spectra were confirmed by using the improved cell, consisting of LSM- YSZ/YSZ/LSM-YSZ. These spectra were a strong function of operating temperature and the stable conditions for the cells were typically reached at $900^{\circ}C$. The typical spectra measured for an air//air cell at $900^{\circ}C$ were composed of two arcs. Addition of YSZ to the LSM electrode led to a pronounced decrease in cathodic resistivity of LSM-YSZ composite electrodes. Polishing the electrolyte surface to eliminate the influences of surface impurities could further reduce cathode resistivity. The cathodic resistivity of the LSM-YSZ electrodes with catalytic interlayer (Ni or Sr) was much smaller than that of LSM-YSZ electrodes without catalytic interlayer. In addition, the cathodic resistivity of the LSM-YSZ electrodes was a strong function of composition of electrode materials, the electrolyte geometry, and applied current.

• Journal of the East Asian Society of Dietary Life
• /
• v.18 no.3
• /
• pp.361-367
• /
• 2008

This study examined the physicochemical properties of rice embryo in order to investigate the antioxidative effect of black rice bran pigment fraction on rice embryo lipid oxidation. Color stability of rice bran pigment fraction and acid value of added rice embryo were determined at various conditions of pH, temperature, and storage time. Rice embryo contained more crude protein (22.1%) compared to the rice bran (9.4%). However, rice embryo had a higher lipid content than rice bran, causing lipid oxidation during storage. Pigment fraction were relatively stable in acidic pH of 3.0 stored at $4^{\circ}C$ for 9 days. Rice embryo showed increased acid value with increased storage time and temperature. Furthermore, rice embryo with pigment fraction resulted in lower acid value compared to the control group. Therefore, addition of black rice bran pigment fractions to rice embryo improved storage capacity.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.6
• /
• pp.4237-4244
• /
• 2015

This study examined the efflorescence characteristics of a concrete sidewalk block manufactured using recycled stone powder sludge and photocatalytic generated by surface polishing during the sidewalk block manufacturing process. The study evaluated the characteristics of the sidewalk block in terms of its quality, based on the amount of stone powder sludge used, efflorescence, and further based on the mixing ratio and number of applications of the photocatalytic. The experimental results indicated that heavy metals such as lead, hexavalent chrome, cadmium, and mercury were not present in the concrete sidewalk block, thereby confirming the effectiveness of the recycled stone powder sludge. The optimum mixing ratio of used in the concrete sidewalk block (for satisfying KS standard values such as water absorption ratio and flexural strength) was found to be 20%. The concrete sidewalk block incorporating the stone powder sludge and photocatalytic exhibited a water absorption ratio of 5.4% and flexural strength of 5.2 MPa, thereby satisfying the quality standards. Additionally, when the photocatalytic was used, efflorescence did not occur even at the low temperature of $-5^{\circ}C$, and the by the sidewalk block was found to be 70% under normal conditions and 68% when subjected to an accelerated weathering test.

• Korean Journal of Optics and Photonics
• /
• v.33 no.2
• /
• pp.74-83
• /
• 2022

The entire process, from the raw material to the final system qualification test, has been developed to fabricate a large-diameter, lightweight reflective-telescope system for a satellite observation. The telescope with 3 anastigmatic mirrors has an aperture of 700 mm and a total mass of 66 kg. We baked a silicon carbide substrate body from a carbon preform using a reaction sintering method, and tested the structural and chemical properties, surface conditions, and crystal structure of the body. We developed the polishing and coating methods considering the mechanical and chemical properties of the silicon carbide (SiC) body, and we utilized a chemical-vapor-deposition method to deposit a dense SiC thin film more than 170 ㎛ thick on the mirror's surface, to preserve a highly reflective surface with excellent optical performance. After we made the SiC mirrors, we measured the wave-front error for various optical fields by assembling and aligning three mirrors and support structures. We conducted major space-environment tests for the components and final assembly by temperature-cycling tests and vibration-shock tests, in accordance with the qualifications for the space and launch environment. We confirmed that the final telescope achieves all of the target performance criteria.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.48 no.4
• /
• pp.467-475
• /
• 2021

The purpose of this study was to compare the effect of sodium fluoride(NaF) varnish and potassium iodide(KI) on remineralization efficacy of silver diamine fluoride(SDF) by measuring microhardness and evaluating surface morphology by scanning electron microscope(SEM). Artificial caries lesions were induced on extracted primary molars and vickers microhardness was measured. Specimens were randomly separated into 4 groups for treatment. The specimens in group I were treated with SDF, group II with NaF varnish after SDF, group III with KI after SDF and group IV with distilled water. After 8 days of pH cycling, vickers microhardness was measured and difference before and after treatment was calculated. For SEM, 2 samples were evaluated respectively after enamel polishing, lesion formation and after pH cycling. Group III showed highest increase in microhardness. Group I showed higher increase in microhardness than Group II but without statistical difference. Group IV showed lowest increase in microhardness value among 4 groups. On SEM image, group I, II and III showed smoother and less irregular surface compared to group IV. Amorphous crystal pellicles were observed in group III. In conclusion, SDF, SDF and NaF, SDF and KI groups showed smoother surface and increase in microhardness suggesting the possibility that remineralization effect might take place in oral conditions. In addition, in limited conditions of this study, applying NaF varnish after SDF did not increase the remineralization efficacy of SDF while KI significantly increased the remineralization efficacy of SDF. However, additional study considering various conditions that might affect demineralization and remineralization in clinical situations need to be conducted.

• International Journal of Ocean System Engineering
• /
• v.2 no.3
• /
• pp.185-194
• /
• 2012

A Macroscopic combination of two or more distinct materials is commonly referred to as a "Composite Material", having been designed mechanically and chemically superior in function and characteristic than its individual constituent materials. Composite materials are used not only for aerospace and military, but also heavily used in boat/ship building and general composite industries which we are seeing increasingly more. Regardless of the various applications for composite materials, the industry is still limited and requires better fabrication technology and methodology in order to expand and grow. An example of this is that the majority of fabrication facilities nearby still use an antiquated wet lay-up process where fabrication still requires manual hand labor in a 3D environment impeding productivity of composite product design advancement. As an expert in the advanced composites field, I have developed fabrication skills with the use of machinery based on my past composite experience. In autumn 2011, the Korea government confirmed to fund my project. It is the development of a composite sanding machine. I began development of this semi-robotic prototype beginning in 2009. It has possibilities of replacing or augmenting the exhaustive and difficult jobs performed by human hands, such as sanding, grinding, blasting, and polishing in most often, very awkward conditions, and is also will boost productivity, improve surface quality, cut abrasive costs, eliminate vibration injuries, and protect workers from exposure to dust and airborne contamination. Ease of control and operation of the equipment in or outside of the sanding room is a key benefit to end-users. It will prove to be much more economical than normal robotics and minimize errors that commonly occur in factories. The key components and their technologies are a 360 degree rotational shoulder and a wrist that is controlled under PLC controller and joystick manual mode. Development on both of the key modules is complete and are now operational. The Korean government fund boosted my development and I expect to complete full scale development no later than 3rd quarter 2012. Even with the advantages of composite materials, there is still the need to repair or to maintain composite products with a higher level of technology. I have learned many composite repair skills on composite airframe since many composite fabrication skills including repair, requires training for non aerospace applications. The wind energy market is now requiring much larger blades in order to generate more electrical energy for wind farms. One single blade is commonly 50 meters or longer now. When a wind blade becomes damaged from external forces, on-site repair is required on the columns even under strong wind and freezing temperature conditions. In order to correctly obtain polymerization, the repair must be performed on the damaged area within a very limited time. The use of pre-impregnated glass fabric and heating silicone pad and a hot bonder acting precise heating control are surely required.

• Korean Journal of Agricultural Science
• /
• v.8 no.1
• /
• pp.97-107
• /
• 1981

This study was carried out in order to provide the basic data necessary to develop the effective and desirable cooking method on large scale for investigating the physical characteristics of cooked rices and studying optimum cooking conditions by pressure in kettle cooking rices. Milyang-15, local Japonica type and Milyang-23, high yielding Indica type major varieties cultivated in Korea were used as cooking sample after polishing 70% and 90% respectively, and the results obtained are summarized as follows. 1. The average moisture content of cooked rice by open kettle and pressure kettle method in typical households were 65.17% and 64.52%, respectively. 2. In water absorption capacity of rice grain Milyang-23 was 4.5% higher than Milyang-15, and maximum water content after absorption in Milyang-23 was 29.14%. 3. The expansion volume of cooked rice was changed proportionally by water absorption, heating temperature and time, and maximum expansion volume of cooked rice was 3.2 times greater than rice grain. 4. The gelatinization degree of cooked rice intensively concerning in hardness of rice grain was increased as water-to-rice ratio, heating temperature and time increased, and it was 0.44 in Milyang-23 and 0.64 in Milyang-15 under the optimum cooking conditions as 160% water-to-rice ratio, $0.2kg/cm^2$ cooking pressure and 25 minutes cooking time. 5. The hardness of cooked rice was decreased as water-to-rice ratio, heating temperature and time increased, and it showed 2.35kg/wt in 90% polished Milyang-23 and 2.0kg/wt in 90 polished Milyang-15 under optimum cooking conditions. For maintaining the same level of hardness of cooking rice Milyang-23 required 25% much more water than Milyang-15. 6. The elasticity of cooked rice was changed proportionally by water-to-rice ratio, heating temperature and time, and it appeared 19.2mm and 15.7mm in 90% polished Milyang-15 and Milyang-23 respectively. 7. The gumminess of cooked rice was decreased as water-to-rice ratio, heating temperature and time increased, and it showed 60 and 73 in 90% polished Milyang-23 and Milyang-15, respectively. 8. The optimum cooking time on differerent pressure in kettle took 25 minutes at $0.2kg/cm^2$, 20 minutes at $0.4kg/cm^2$, 15 minutes at $0.6kg/cm^2$, and 10 minutes at $0.8kg/cm^2$.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.2
• /
• pp.91-96
• /
• 2012

In this study we investigated the effects of operational parameters of a multi-layered soil filtration (filter depth, filtration velocity, and continuous/intermittent operation) on removal of pollutants in river water. As filter depth increased removal of all the pollutants (COD, TP, TN, and $NH_4$-N) was increased because the increase in filter depth increased in contact time between media and pollutants. The removal of TP and $NH_4$-N more increased with the increase in filter depth, comparing to the biological COD removal which was performed only in the top layer, since the removal mechanism of TP and $NH_4$-N was physicochemical process occurring throughout the whole layers. However, the reduction in filtration velocity resulted in decrease of removal all the pollutants removal due to shorter retention time. Biological COD removal was more influenced with the reduction in filtration velocity (longer retention time), than the removal of TP and $NH_4$-N. Because biological process was occurred only in the top layer which has relatively shorter retention time, comparing with physicochemical process occurred throughout whole media. Therefore, it is desirable that the operation parameters be controlled toward increasing retention time, in order to achieve efficient pollutants removal. The change in operation mode (continuos vs. intermittent operations) did not provide significant effects on the pollutant treatment efficiency by the multi-layered soil filtration system. Our findings suggest that for stable long-term operation it should be considered keeping conditions for biological activity and accelerating clogging.

• Journal of Technologic Dentistry
• /
• v.33 no.1
• /
• pp.93-102
• /
• 2011

Purpose: The study aimed to evaluate working environment for dental technician by measuring dust level, ventilation conditions and the use of personal protective equipment and to provide basic information required to improve working environment and develop health education programs for dental technician. Methods: A total of 240 dental technician who are registered with the Daegu Association of Dental technician and working at 34 dental laboratories participated in the study. And the dust level was measured at 21 different spots in 16 dental laboratories out of 34. Results: Of 34 dental laboratories, 31 (91.2%) were equipped with a ventilator, but the remaining 3 (8.8%) did not have a ventilator. By the number of ventilator, 1 to 3 ventilators were found in 22 dental laboratories (71.0%), 4 to 6 ventilators were in 7 laboratories (22.5%) and more than 7 ventilators in 2 laboratories(6.5%). According to the frequence of changing filters in dust collector, 20 dental laboratories (58.9%) changed filters every four weeks, 10 laboratories (29.4%) changed them every six weeks and 4 laboratories (11.7%) changed them every eight weeks. Of total respondents, 114 (61.3%) said they wore a mask all the time while working, 56 (29.6%) said they frequently wore a mask, 19 (10.1%) said they did not wear a mask. As for the type of masks, 159 (84.1%) used a disposable mask, 25 (13.2%) used a cotton mask and 5 (2.7%) used an anti-dust mask. For dust sat on their outfits while working, 102 (54.0%) shook their uniforms inside workplace to keep dust off the uniforms, 64 (33.9%) did not anything until they wash their uniforms and 23 (12.1%) shook their uniforms outside workplace to keep dust off the uniforms. Of total respondents, 182 (96.3%) had a particle in their eyes while carrying out grinding work. Based on the measurement of floating dust at workplace, 3 dental laboratories showed dust concentration exceeding the minimum level of 10 mg/$m^3$ allowed under the permit for environment. Of those, 1 laboratory had the dust concentration that was more than 1.5 times higher than the minimum level. Dust concentration was higher in laboratories that used a dust collector with 0.5 horse power and changed filters more than 3 weeks ago. Dust comprised of nickel (more than 70%), chrome (9%) and others. The mean chrome concentration was more than twice higher than the minimum permissible level of 0.5 mg/$m^3$. There were two laboratories that showed chrome concentration exceeding the level of 0.4 mg/$m^3$. Like dust concentration, chrome level was higher in laboratories that used a dust collector with 0.5 horse power and changed filters more than 3 weeks ago. There were six laboratories that had nickel concentration exceeding the minimum permissible level of 1 mg/$m^3$. Of those, one laboratory had nickel concentration that was more than three times higher than the minimum permissible level. Nickel concentration was also higher in laboratories that used a dust collector with 0.5 horse power and changed filters more than 3 weeks ago. Conclusion: It is not likely that heavy metal concentrations found in the study constitute respiratory dust. It is however necessary for health of dental technician to apply the Industrial Safety and Healthy Law to dental laboratories and make recommendations for the use of personal protective equipment, installation of a proper number of ventilators, more frequent change of filters in dust collector and improved ventilation for polishing work. At the same time, dental technician need education on how to use personal protective equipment and how to efficiently remove dust from their uniforms.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.35 no.1
• /
• pp.10-24
• /
• 2017

The research takes note of the formation process and settling period of Gwandong-Palkyung(關東八景, Eight Sites of Eastern Korea), the representative palgyeong(prominent eight sites) and jipgyeong(集景, landscape collection of scenic beauty), and investigates the time of formation regarding the palkyung and jipgeyong of Gwandong's scenic beauty through the analysis and interpretation of bibliographic data, and reference data. The result of the study is as follows. As the first document that records the terminology of "Gwandong-Palkyung" is "Daphongeunggil(答洪應吉)" of Yi, Hwang(李滉), Gwandong-Palkyung is inferred to be settled within the recognition of the people even before the 16th century. The geographic analysis result including "Sinjeung Donggukyeojiseungram(新增東國輿地勝覽)", Gwandong-Palkyung expanded as Gwandong-Sipkyung in early to middle of the 16th century. The first confirmed landscape collection regarding Gwandong-Palkyung in this study is confirmed in Shin Zup(申楫)'s "Yeonggwandong-Palkyung(詠關東八景)", thus, the terminology of Gwandong-Palkyung existed before 16th century at the latest. The settlement time of current "Palkyung" collection is estimated to be early 17th century at the latest. Poetries regarding Gwandong-Palkyung, and the frequency on the appearance of Gwandong scenic beauties are analyzed as making clear of the concentrated phenomenon on the sceneries of Gwandong-Palkyung. On the other hand, the collection of Gwandong-Palkyung in the domain of arts is confirmed initially in the ${\ll}$Gwandongpalkyungdobyeong(關東八景圖屛)${\gg}$ of Heo, Pil(許泌). Gwandong-Palkyung, expressed as the actual scene landscape painting shows similar tendencies of the conditions in the jipgyeong from the poetry, but the appearance rate of the painting subject was more prominent in visual solidarity and cohesion due to the reflection of the importance on icon(圖像) of the art works produced with particular meaning in the case of fixed ideal system. From late Joseon to modern times, ${\ll}$palpokbyeongpung(八幅屛風)${\gg}$ of various forms of folk painting is a corroborative evidence notifying that the cultural phenomenon of Gwandong-Palkyung has entered the universal period of embrace. Also, the 13 scenic beauties of Gangwon-Do appearing in the games of Namseungdo and Myeongseungyuramdo include Gwandong-Palkyung, which confirms the settlement of Gwandog-Palkyung even within the culture of games in late Joseon. Such results demonstrate the existence of awareness regarding Gwandong-Palkyung from the first half of the 15th century, which is presumed to have completely settled in the 17th century through the continuous development of formative process in the 16th century. Ultimately, Gwandong-Palkyung is the concrete formation of regional scenic beauties that individually gained its reputations as scenery from the Koryo Dynasty to late 17th century. Gwandong-Palkyung of the scenic beauty of Gwandong is a unique cultural scenery of the region that have germinated and formed through the process of cutting and polishing of long time to collect the best eight of scenic beauty from the many participation of sightseeing culture.