• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.9
• /
• pp.651-657
• /
• 2003

We have demonstrated an in-line polarization splitter based on a side-polished fiber coupler including a thin metal intermediate layer. The experimental results revealed that the metal layer with proper thickness prevents TE polarization component from optical coupling between two contacted side-polished fibers, whereas it allows TM polarization component to the coupling. The design and fabrication techniques about the polarization splitter exploiting the side-polished fibers have been presented. The fabricated polarization splitter exhibited 18dB and 23dB of isolation ratio for TE polarization and TM polarization, respectively. The measured insertion loss for TE and TM polarization was 0.7dB and 1.3dB, respectively.

• Tribology and Lubricants
• /
• v.19 no.1
• /
• pp.31-35
• /
• 2003

This paper reports the studies on the wear-corrosion behavior of ductile cast iron in the various pH environments. In the variety of pH solutions, corrosion and wear-corrosion loss of GCD 600 were investigated. Also, the anodic polarization test of GCD 600 using potentiostat/galvanostat was carried out. And rubbed surface of GCD 60 using scanning electron micrographs after immersion and wear-corrosion test was examined in the environment of various pH values. The main results are as following In alkali zone, the wear-corrosion loss of GCD 600 increases, but corrosion loss decreases. The unevenness and crack of wear-corrosion surface in neutral zone becomes duller than that in alkali zone. As the corrosive environment is acidified, wear-corrosion behavior of GCD 600 with passing immersion time becomes sensitive.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.05a
• /
• pp.152-157
• /
• 2001

This paper was studied on the characteristics of crevice corrosion prevention of SS 400 in marine environment. In NaCl solution, polarization behavior under the crevice corrosion was investigated. And Weight loss rate of SS 400 applied cathodic protection and non cathodic protection was measured according to the NaCl concentration. The main results obtained are as follows : The weight loss rate of Al-alloy galvanic anode was increased as the concentration of NaCl solution increased by 3.5% but the concentration increased over 3.5%, that of Al-alloy galvanic anode become decreased. The protective potential of SS 400 used Al-alloy galvanic anode becomes more cathodic polarization with increasing concentration of NaCl solution. Effects of oxygen on the weight loss rate of Al-alloy sacrificial anode for cathodic protection as the concentration of 3.5% NaCl solution become sensitive than that of 0% NaCl solution.

• Transactions of the Korean hydrogen and new energy society
• /
• v.21 no.6
• /
• pp.533-539
• /
• 2010

Ni-YSZ supported button cells were prepared by spray-coating YSZ and screen-printing YSZ-LSM powder as an electrolyte and oxygen electrode on Ni-YSZ cermet disks. In order to identify the polarization loss mechanism in high temperature electrolysis current-voltage characteristics coupled with electrochemical impedance spectroscopy were investigated as a function of temperature, current load, and the humidity. The effects of the different current collectors of platinum and silver for oxygen electrodes were compared. With Ag current collector two polarization losses were distinguished. The high frequency component was attributed to the Ni-YSZ cermet which was less susceptible to temperature variation but increasing in loss with humidity. The lower frequency component was attributed to the LSM electrode. Platinum current collector led to a much lower polarization loss.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.20 no.2
• /
• pp.72-78
• /
• 2021

This paper proposes a wide-band dual-polarization stacked patch array antenna for satellite SAR system applications. The array antenna was designed for loss minimization and wide-band characteristics to enhance the performance of the SAR system and optimize it for active return loss in applications to active phased arrays. The fabricated array antenna showed a performance of 19.26%/19.79% fractional bandwidth within the -10 dB reference level of the active return loss and showed loss characteristics of 0.797 dB/0.799 dB averaged within the operational frequency for both H/V-polarization cases. The pattern performance was verified by comparing the measured patterns with the calculated patterns obtained by the array factor.

• Journal of Information Display
• /
• v.10 no.1
• /
• pp.28-32
• /
• 2009

The correlation between the optical performance of the reflective polarizer, which is a key optical component for the brightness enhancement of the liquid crystal display (LCD), and the configuration of optical sheets was investigated in a direct-lit CCFL (cold-cathode fluorescent lamp) backlight. The optical gain of the reflective polarizer, the polarization state of the light emitted from each film, and the loss factor for the polarization conversion process occurring in the lower part of the backlight were determined using a phenomenological approach for the polarization recycling process. The present study suggests that the correlation between the optical performance of the brightness enhancement films and the backlight configuration should be carefully considered in the optimization of the backlight structure.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.33 no.3
• /
• pp.112-117
• /
• 1984

The dielectric propertries of polymers are very important to investigate the molecular structure of polymer. The characteristrics of the dielectric absorption in vulcanized natural rubber were studied in the range of frequency from 10[KHz] to 32[MHz] at the temperature of 25[$^{\circ}C$]. As the results. it has been confirmed that in the case of natural ruber vulcanized between 2 and 4phr the specimens exhibit two kind of dielectric losses due to the dipole polarization by impurites and sulfure, and of above 7phr was only a loss due to the dipole polarization by sulfure and of natural rubber exhibit two kind of losses due to the interfacial and the dipole polarization. Furthermore, dielectric loss maximun tan spectrum, which removed to the low frequency according to increasing sulfure, depends greatly on sulfure. The volume resistivity of $10^{7}$~$10^{11}$[$\Omega\cdot$cm], regardness whether the crosslinking of rubber are tired by sulfure or, was observed.

• Corrosion Science and Technology
• /
• v.5 no.5
• /
• pp.160-167
• /
• 2006

S-Acetyl Isothiourea Acetate (S-AITA) was synthesized in the laboratory and this influence on the inhibition of corrosion of mild steel in 1.11 N hydrochloric and 1.12 N sulphuric acids was investigated by weight loss and potentiostatic polarization techniques at 303K, 353K and 403K. These results were confirmed by the impedance technique. The inhibition efficiency increased with increase in concentration of inhibitor and decreased with rise in temperature from 303K to 403K. The maximum inhibition efficiency of S-AITA was found to be 99.95% (0.5% of S-AITA) at 303K in sulphuric acid. The adsorption of this compound on the mild steel surface from the acids has been found to obey Temkin's adsorption isotherm. The potentiostatic polarization results revealed that S-AITA was a mixed type inhibitor. Some thermodynamic parameters i.e., activation energy (Ea), free energy of adsorption (${\Delta}G_{ads}$), enthalpy of adsorption (${\Delta}H$) and entropy of adsorption (${\Delta}S$) were also calculated from weight loss data.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.9B
• /
• pp.1534-1541
• /
• 2000

Wavelength tunable fiber ring laser can be tuned by causing a resonance on the optical path having the least loss which is controlled by a polarization adjustment. It is observed that lasing wavelengths having 1 nm FSR(Free Spectral Range) can be tuned over the range of 1540-1560 nm when a polarization controller and an intra-cavit polarizer with 1.5 mm air gap are adjusted. The characteristics of wavelength shift in the laser output are analyzed by introducing an optical path modeling and the concept of a birefringence loss.

• Korean Journal of Optics and Photonics
• /
• v.13 no.5
• /
• pp.408-413
• /
• 2002

We demonstrated a polarization dependent type 2$\times$2 optical switch, using a binary reflection type SLM. Reflection type FLC was used as a half wave retardation plate. Two inputs were controlled by each SLM for the desired output direction. In conclusion, in the "1" state the average optical loss was 6.6 ㏈, and in the "0" state the average optical loss was 14.6 ㏈, and measured the switching speed as 75 $mutextrm{s}$. By using this method, a polarization dependent type 2$\times$2 optical switch can be demonstrated and the possibility of a 4-port WDM optical switch also verified.