• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.24 no.1
• /
• pp.1-9
• /
• 2016

In this paper, we integrate three degree of freedom(3DOF) point-mass model for aircraft and three-dimensional path generation algorithms using dubins curve and nonlinear path tracking law. Through this integration, we apply the path generation algorithm to the path planning, and verify tracking performance and feasibility of using the aircraft 3DOF point-mass model for air traffic management. The accuracy of modeling 6DOF aircraft is more accurate than that of 3DOF model, but the complexity of the calculation would be raised, in turn the rate of computation is more likely to be slow due to the increase of degree of freedom. These obstacles make the 6DOF model difficult to be applied to simulation requiring real-time path planning. Therefore, the 3DOF point-mass model is also sufficient for simulation, and real-time path planning is possible because complexity can be reduced, compared to those of the 6DOF. Dubins curve used for generating the optimal path has advantage of being directly available to apply path planning. However, we use the algorithm which extends 2D path to 3D path since dubins curve handles the two dimensional path problems. Control law for the path tracking uses the nonlinear path tracking laws. Then we present these concomitant simulation results.

• Journal of Advanced Navigation Technology
• /
• v.21 no.3
• /
• pp.264-271
• /
• 2017

This paper presents air traffic control simulation model for generating 4D trajectory, and aircraft dynamic model based on 4D trajectory information. With aircraft parameters from BADA and Total Energy Model, the trajectory is defined through modified Bezier curve and the simulation supports two aircraft control methods based on controlled time of arrival (CTA) or airspeed. The simulation results shown that flight time and path were almost identical to the defined trajectory, and derived the differences of each control methods according to wind conditions. Based on the simulation model developed in this study, it is expected to be applied to various air traffic management researches. Future studies will focus on applying optimization techniques in order to minimize the difference between generated trajectories and actual flight routes. This work will increase utilization of developed simulation futhermore.

• Advances in aircraft and spacecraft science
• /
• v.10 no.3
• /
• pp.245-256
• /
• 2023

In order to improve aerodynamic performance of multi-stage axial flow turbines used in aircraft engines, a one-dimensional aerodynamic design and optimization framework is constructed. In the method, flow path is generated by solving mass continuation and energy conservation with loss computed by the Craig & Cox model; Also real gas properties has been taken into consideration. To obtain an optimal result, a multi-objective genetic algorithm is used to optimize the efficiencies and determine values of various design variables; Final design can be selected from obtained Pareto optimal solution sets. A three-stage axial turbine is used to verify the effectiveness of the developed optimization framework, and designs are checked by three-dimensional CFD simulation. Results show that the aerodynamic performance of the optimized turbine has been significantly improved at design point, with the total-to-total efficiency increased by 1.17% and the total-to-static efficiency increased by 1.48%. As for the off-design performance, the optimized one is improved at all working points except those at small mass flow.

• 한국항공운항학회:학술대회논문집
• /
• 2015.11a
• /
• pp.247-251
• /
• 2015

본 논문에서는 항공기의 3자유도 질점 모델과 Dubins 곡선을 이용한 3차원 경로생성 알고리즘 및 비선형 경로추종 유도기법을 통합하여 항공기의 경로계획을 위해 적용한 경로생성 알고리즘을 검증하고, 경로추종 성능과 항공교통관리를 위한 시뮬레이션에 3자유도 질점 항공기 모델 사용의 타당성을 확인하였다. 최적경로 생성을 위해 사용된 Dubins 곡선의 경우 계산속도가 빠르고 경로계획에 바로 적용이 가능하다는 장점이 있다. 하지만 주로 2차원 상의 경로문제를 다루기 때문에 이를 3차원 비행경로로 확장시킨 알고리즘을 사용하였다. 경로추종을 위한 유도제어법칙은 Specific Acceleration 명령을 통해 자세를 제어하는 비선형 경로추종 유도법칙을 활용하였으며, 이에 대한 결과를 확인하였다.

• Advances in aircraft and spacecraft science
• /
• v.3 no.3
• /
• pp.243-257
• /
• 2016

The increase of air traffic volume has brought an increasing amount of issues related to carbon and NOx emissions and noise pollution. Aircraft manufacturers are concentrating their efforts to develop technologies to increase aircraft efficiency and consequently to reduce pollutant discharge and noise emission. Ultra High By-Pass Ratio engine concepts provide reduction of fuel consumption and noise emission thanks to a decrease of the jet velocity exhausting from the engine nozzles. In order to keep same thrust, mass flow and therefore section of fan/nacelle diameter should be increased to compensate velocity reduction. Such feature will lead to close-coupled architectures for engine installation under the wing. A strong jet-wing interaction resulting in a change of turbulent mixing in the aeroacoustic field as well as noise enhancement due to reflection phenomena are therefore expected. On the other hand, pressure fluctuations on the wing as well as on the fuselage represent the forcing loads, which stress panels causing vibrations. Some of these vibrations are re-emitted in the aeroacoustic field as vibration noise, some of them are transmitted in the cockpit as interior noise. In the present work, the interaction between a jet and wing or fuselage is reproduced by a flat surface tangential to an incompressible jet at different radial distances from the nozzle axis. The change in the aerodynamic field due to the presence of the rigid plate was studied by hot wire anemometric measurements, which provided a characterization of mean and fluctuating velocity fields in the jet plume. Pressure fluctuations acting on the flat plate were studied by cavity-mounted microphones which provided point-wise measurements in stream-wise and spanwise directions. Statistical description of velocity and wall pressure fields are determined in terms of Fourier-domain quantities. Scaling laws for pressure auto-spectra and coherence functions are also presented.

• Korean Journal of Remote Sensing
• /
• v.28 no.6
• /
• pp.693-704
• /
• 2012

Space-born remote sensing camera systems tend to be developed to have very high performances. They are developed to provide extremely small ground sample distance, wide swath width, and good MTF (Modulation Transfer Function) at the expense of big volume, massive weight, and big power consumption. Therefore, the camera system occupies relatively big portion of the satellite bus from the point of mass and volume. However, the camera systems for lunar exploration don't need to have such high performances. Instead, it should be versatile for various usages under various operating environments. It should be light and small and should consume small power. In order to be used for national program of lunar exploration, electro-optical versatile camera system, called MAEPLE (Multi-Application Electro-Optical Payload for Lunar Exploration), has been designed after the derivation of camera system requirements. A ground model of the camera system has been manufactured to identify and secure relevant key technologies. The ground model was mounted on an aircraft and checked if the basic design concept would be valid and versatile functions implemented on the camera system would worked properly. In this paper, results of design and functional test performed with the field campaigns and air-born imaging are introduced.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.4
• /
• pp.92-98
• /
• 2002

In this study, maximum launch range and F-pole are evaluated and analyzed for the semi-active radar missile concerning various launch condition, performance limitation and target maneuvers. Furthermore, general evasion maneuvers are considered when shooter approaches to target with head-on conditions. A point-mass target, shooter and missile model is used including aircraft and missile dynamics. More realistic missile motion simulation is conducted using aerodynamic performance data, geometry, performance limitation, radar seeker performance and so on. Maximum launch range, which is the distance for intercept satisfying target and missile motion and performance, is evaluated using root finding method. F-pole, which is the distance between target and shooter when intercept is completed, is evaluated assuming that shooter maneuvers through pursuit guidance to target.