• Journal of the Korean GEO-environmental Society
• /
• v.22 no.12
• /
• pp.41-50
• /
• 2021

This study investigated the changes in engineering characteristics of sand-tire chip mixtures during repetitive loading. To quantify the changes in the maximum shear modulus according to the tire chip content in the mixtures and the particle size ratio between sand particle and tire chip, the samples were prepared with tire chip content of TC = 0, 10, 20, 40, 60, and 100%, and the particle size ratios SR were also set to be SR = 0.44, 1.27, 1.87, and 4.00. The stress of the prepared sample was applied through a pneumatic cylinder. The experiment was conducted in the order of static loading (= 50 kPa), cyclic loading (= 50-150 kPa), static loading (= 400 kPa) and unloading. The stress applied to tested mixtures was controlled by a pressure panel and a pneumatic valve by using an air compressor. The shear wave velocity was measured during static and cyclic loadings by installing bender elements at the upper and lower caps of the mold. The results demonstrated that the change in maximum shear modulus of all tested materials with varying SR during repetitive loading is the most significant when TC ~ 40%. In addition, the mixture with smaller SR at a given TC shows greater increase in maximum shear modulus during repetitive loading.

• Elastomers and Composites
• /
• v.5 no.2
• /
• pp.181-187
• /
• 1970

In vulcanizates of NR/SBR blending compounds, the physical properties decrease as the contents of SBR increase for the most part. but the abrasives showed reverse performance. However, since these conditions enough satisfy the requirements of tread, carcass and sidewall of tire, we found it was possible to take use of the quantity of SBR contained high on tire manufacturing.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.4
• /
• pp.247-254
• /
• 2015

Ride comfort is one of the major factors in evaluating the performance of the vehicle. Tire is closely related to the ride comfort of the vehicle as the only parts in contact with the road surface directly. Vertical stiffness which is one of the parameters to evaluate the tire performance is great influence on the ride comfort. In general, the lower the vertical stiffness, the ride comfort is improved. Research for improving the ride comfort has been mainly carried out by optimizing the shape of the pneumatic tire. However, demand for safety of the vehicle has been increased recently such as a run-flat tire which is effective in safety improvement. But a run-flat tire have trouble in practical use because of poor ride comfort than general tire. Therefore, In this paper, the research was carried out for improving the ride comfort through the optimization of the SIR shape inside a run-flat tire. Meta-model was generated by using the design of experiment and it was able to reduce the time for the finite element analysis of optimization. In addition, Shape optimization for improving the ride comfort was performed by using the genetic algorithm which is one of the global optimization techniques.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.5
• /
• pp.746-755
• /
• 1997

This paper addresses the systematic procedure using sequential approach for the analysis of the coupled thermo-mechanical behavior of a steady rolling tire. Not only the knowledge of mechanical stresses but also of the temperature loading in a rolling tire are very important because material damage and material properties are significantly affected by the temperature. In general, the thermo-mechanical behavior of a pneumatic tire is highly complex transient phenomenon that requires the solution of a dynamic nonlinear coupled themoviscoelasticity problem with heat source resulting from internal dissipation and friction. In this paper, a sequential approach, with effective calculation schemes, to modeling this system is presented in order to predict the temperature distribution with reasonable sccuracies in a steady state rolling tire. This approach has the three major analysis modules-deformation, dissipation, and thermal modules. In the dissipation module, an analytic method for the calculation of the heat source in a rolling tire is established using viscoelastic theory. For the verification of the calculated temperature profiles and rolling resistance at different velocities, they were compared with the measured ones.

• Aerospace Engineering and Technology
• /
• v.6 no.1
• /
• pp.19-28
• /
• 2007

In this study, a nonlinear 2 degree of freedom mathematical model has been developed for impact analysis of the nose landing gear of a light aircraft which is composed of an wheel & tire, an Oleo-pneumatic shock strut and the castering wheel fork for the differential braking steering, and then the response of impact is computed using a numerical method. The mathematical model of a nose landing gear contains nonlinear characteristics which are an impact load - deflection property of a tire and internally frictional forces between an inner surface of an upper cylinder and a bearing of a lower rod due to side forces like the declined angle of strut, the moment due to an wheel fork, the side drag due to a steering and it is computed using the 4th-order Runge-Kutta method. The comparison process between analytical results and experimental results of the other proven nose landing gear is carried out to verify the mathematical model.

• Journal of Biosystems Engineering
• /
• v.12 no.4
• /
• pp.9-15
• /
• 1987

The vibrational characteristics of a radial-ply (155SR13 4PR) and a biased-ply tire (6.15-134PR) were investigated for examining the effects of tires with different structure on the ride characteristics of the vehicle. The natural frequencies at the tread band, mode shapes, and damping factors of two tires at the state of plane vibration were determined experimentally. The test work was performed at four levels of the inflation pressure, ranging from 171.7 kPa to 245.2 kPa, and three levels of the vertical load, deviating by 10% from the standard load designated by the Department of Transportation of the United States of America. The following results were drawn by the analysis of the test results: 1. The first-order natural frequencies of the radial-ply and the biased-ply tires at the tread band were 112 Hz and 159 Hz, respectively, at the state o f the free vibration when the inflation pressure of 196.2 kPa was applied. It was known that the biased-ply tire has higher resonant frequency than the radial-ply tire and the natural frequencies of the both tires move to the high frequency range as t he inflation pressure is increased. 2. The vibration modes of both tires were quite different. No big difference in mode shapes was examined as the inflation pressure was increased. But the natural frequencies of two tires were changed. For the radial-ply tire, no difference in mode shape was found whether the vertical load was applied or not. But a significant difference in mode shape was examined for the biased-ply tire. 3. Any difference was not found in damping factor as the different inflation pressures were applied. 4. When no vertical load was applied, damping factors of the radial-ply and biased-ply tire at the state of the natural vibration ranged from 2.6 to 5.9%, and from 4.1 to 7.8%, respectively. It was estimated that the radial-ply tire would have better cushioning than the biased-ply tire since the vertical spring rate of the radial-ply tire was much less than that of the biased-ply tire, even though the damping effect of the radial-ply tire was smaller than that of the biased-ply tire.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.4
• /
• pp.330-335
• /
• 2012

This study performed the structure analysis for development and localization of main and nose wheel in Korean Helicopter Program(KHP). Structural stability of wheel is evaluated using ANSYS. Considering wheel and tire interface, Stress analysis was conducted by applying pneumatic of tire, static load, radial load and combined load on main and nose wheel. Considering yield strength at which plastic deformation occurs, simulation results suggest the method which increases structure stability after comparing maximum stress and yield strength.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.22 no.5
• /
• pp.663-668
• /
• 2012

A TPMS(Tire Pressure Monitoring System) is a wireless communication system designed to monitor the pressure and temperature of pneumatic tires of a vehicle. In order to provide the aid in protecting a driver, this system reports tire pressure information to the driver of the vehicle. Since the wireless communication technique should be employed to transmit the TPMS data from each tire to signal processing unit in the vehicle, it suffers from interference signals from external electrical or electronics equipments. In this paper, we propose the TPMS interference cancellation technique based on GSC(Generalized Sidelobe Canceler), which does not have only the excellent performance like MVDR(Minimum-Variance-Distortionless-Response) but also has the low computational complexity comparing with MVDR. The performance of interference suppression is conformed by computer simulation examples.

• Elastomers and Composites
• /
• v.3 no.1
• /
• pp.32-38
• /
• 1968

The physical properties of NR-SBR and NR-BR blends were studied. 1. In blending, tensile strength decreased with increase in synthetic rubber contents. It was most effective when the ratio of NR/Syn. R is 75/25. 2. Tensile strength decreased with order of NR, SBR and BR and modulus after aging is proportional of synthetic rubber contents. 3. Elongation is less influenced by synthetic rubber ratio that on the other hand, the decrease of elongation is proportional to synthetic rubber contents after aging. 4. Hardness decreased with increase in the synthetic rubber contents and on the other hand, the hardness increased after aging.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.21 no.4
• /
• pp.436-441
• /
• 2011

A TPMS is a wireless communication system designed to monitor its condition inside the pneumatic tires on various types of vehicles. These systems report the tire pressure information to the driver of the vehicle. While wireless communications is used to transmit the measurement data from TPMS sensors to a central processing unit in the vehicle, it suffers from the various interferences such as sensors of each tire or outside electrical equipments. Based on the conventional beamformer, a switching beamforming technique is proposed to minimize the interference and efficiently receive valid data. Moreover, in order to minimize the interference and reduce power consumption for communication, a system with unique Gold Code is presented for each tire. The performance of interference suppression is illustrated by computer simulations.