• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.3
• /
• pp.353-358
• /
• 2010

This research introduces a new and improved design for a pneumatic cylinder driven roll feeder wherein each of the principal rotating feeder parts is configured so as to have feeding accuracy and to be low manufacturing cost. The feed pitch accuracy of the proposed roll feeder was evaluated by measuring lengths of cut offs of the strip stock with a shear attached to an air press. The air press was designed, manufactured, and mounted on the same table of the proposed roll feeder such that the strip stock maintained horizontal plane until the strip stock entered into the shear. The proposed roll feeder and the air press were designed to be operated automatically by a PLC employed controller. The feed pitch accuracy of the proposed roll feeder was analyzed by setting the pitch as 10, 12.5, and 15mm. At each predetermined feed pitch, the proposed roll feeder was tested 300 times as one test set and replicated three times. The average lengths of the cut offs of the strip stock ranged from 9.98 to 10.13mm, from 12.42 to 12.57mm, and from 14.96 to 15.06mm at the predetermined 10, 12.5, and 15mm feed pitch, respectively, among the total of 900 samples of each feed pitch. Main cause of variation of the length of the cut off of the strip stock fed by the proposed roll feeder was considered to be fluctuation of the air press during recompressing period of the air compressor to pressurize the air in the air tank. The largest difference between the maximum and the minimum length of the cut off was appeared while the air compressor recompressing the air. The air compressor used for this study restricted the air delivered to the proposed roll feeder while it was still running. Thus, this air delivery restriction problem should be improved by stabilizing the air press while the proposed roll feeder is running.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.5 s.182
• /
• pp.155-161
• /
• 2006

This paper introduces a new type of mechanical tape feeder for chip mounter. The mechanical feeder is composed of a pneumatic linear actuator and a linear feeding module with the application of a cam-slider. As semiconductor chips are getting smaller, PCB assembly makers require the feeder to position the chip with high accuracy. The linear feeding system improves the positioning accuracy of the chip by getting rid of the index error, which brings into existence on the sprocket rotating feeder. It also can make greatly reduce the dumping rate. The dumping error is caused by the impact occurred as the pawl to interrupt ratchet wheel rotation. The paper discusses its mechanism and mechanical performance. The positioning accuracy and the dynamic characteristic were measured for long time operation and analyzed. As a result, the feeder showed very good performance. However, the feeding system was dynamically unstable due to the cover film eliminator that is required to be modified

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.4 s.181
• /
• pp.132-138
• /
• 2006

A tape feeder is an important part to supply a micro chip such as 1005 and 0603 components in SMT process. Traditional sprocket wheel type feeder has several problems such as backlash and indexing errors, low compatibility and confidence. However, it is very difficult to solve such problems due to the inevitable fraction defectives of sprocket wheel. Thus, the object of this works is to develop a linear type high precision tape feeding system using cam-slider mechanism. The proposed cam-slider mechanism is composed of several links and a plate, pneumatic actuator is used to generate linear motion. The proposed mechanism has distinct advantages over the conventional mechanism. It has reduced feeding errors, long lift-cycle, and slim width. As a result, the developed tape feeder using cam-slider mechanism shows special characteristics far high precision feeding for chip-mounters.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.852-855
• /
• 2009

고압 미분탄 공급 기술은 건식 석탄가스화기 시스템의 안정적인 연속운전을 위한 핵심이 되는 기술로서, 본 연구에서는 스크류피더 방식 및 기류수송 방식의 pilot급 고압 미분탄 공급장치를 이용한 미분탄 공급량 제어 기술 개발을 진행하였다. 그리고, 일반적으로 dense phase 형태로 다량의 미분탄을 공급하는 기류수송 방식 고압 미분탄 공급장치에서 가스화기로 공급되는 미분탄의 공급량을 감소시키기 위하여 다공 chamber를 통하여 가압 질소를 공급할 경우, 차압이 증가함에 따라 미분탄의 공급량이 증가하기는 하지만 lean 또는 medium phase 형태로 미분탄 공급량 제어가 가능함을 확인할 수 있었다.

• Journal of Biosystems Engineering
• /
• v.6 no.2
• /
• pp.33-47
• /
• 1982

To modernize the conventional rice post production technology and reduce grain losses, a transition toward the wet-paddy threshing system has been strongly demanded. The head-feeding type thresher with pneumatic separation has been used dominantly for threshing dried-paddy, but some adverse effects in separation performance for threshing wet-paddy is encounterred. In order to solve the problems, the development of thresher with an additional oscillating sieve to the conventional pneumatic separation has been recommanded. This study was intended to evaluate the separating performance of thresher with oscillating sieve which was attached additionally to the conventional auto-thresher equipped with separation system of blower and suction fan. For different feed rates and rice varieties, wet-and dry-material were tested with threshers attached with and without oscillating sieve. Results of the study are summarized as follows: 1. When the feed rates were 480 and 640 kg/hr, there was no statistically significant difference in power reqirements between the threshers with and without an additional sieve device for both dry-and wet-threshing. However, when the feed rate was 960 kg/hr, power requirements of thresher without sieve were greater for wet-paddy threshing than the thresher with the additional sieve separator by about 20% points. 2. With additional oscillating sieve device, the ratios of total weights of whole grains including grains with branch let and damaged grains to the total output did not show statistical difference among the feed rates. However, with pneumatic separation the ratio was decreased as the level of feed rate increased. 3. The total amount of grains with branchlet (including broken panicle) increased with the moisture content. For both the wet-and dry-material threshing with the additional oscillating sieve, the percent of grains with branchlet to the total output decreased greatly as the feed rate increased. 4. The output of the damaged grains increased as moisture content decreased. Especially, for the dry-paddy threshing, the additional sieve separating device produced more damaged grains than the pneumatic separation at all feed rates. 5. Generally, for dry paddy threshing, the separating performance of the thresher with the additional sieve device was better at all feed rates, showing greater difference with increasing feed rates. 6. Separating losses were greater with the pneumatic than sieve separation for both the wet-and dry-threshing. 7. The overall comparison of separating performance of threshers tested with and without an additional sieve device showed that the former was more effective than the latter for the dry-material threshing. However, for the wet-paddy threshing, the separation performance with a sieve device was better than the pneumatic only when the feed rate was high.

• 대한공업교육학회지
• /
• v.31 no.1
• /
• pp.211-225
• /
• 2006

Gabion can be used for the purpose of preventing overflow of river and side loss of road. However the manufacturing process of the gabion is manually controlled especially to the joining process at the terminal part of gabion with small diameter wire. In this paper automatic feeding guide system was designed and fabricated to make automation. The fabricated system was tested in the factory level. Pneumatic system was considered as the main idea of the feeding system. 3/2-way and 5/2-way manual control valve, eight double-acting cylinders were used. The system took 46.48 seconds during a cycle. Additional environmental noise and vibration were not detected when the machine operated at the working area. Based on the theoretical simulation and actual test the fabricated system was well controlled. The system was applied to the patent in 2006.

• Journal of the Korean Society of Safety
• /
• v.25 no.5
• /
• pp.15-21
• /
• 2010

Regenerative Energy Storage System(ESS) is a system that saves regenerative energy which generated instantly in the regenerative braking of Electric Multiple Unit(EMU) and disappear, and reuse the stored energy when EMU is in powering. Such system related to a research field of renewable energy which emerged concerning climate change and high oil prices. In the case of existing domestic rolling stock, about 25% to 30% of generated regenerative energy is restored to power source and is regarded as direct factor of raising catenary voltage. Such rapid change of catenary voltage is a cause of the failure of EMU's electronic equipment and lowering its reliability and is also a cause of train's fault occurred by tripping circuit breaker. In this paper, we intend to investigate the effect on blending characteristics of electric-braking and pneumatic-braking whether the regenerative energy storage system is used or not in urban transit DC 1,500V feeding system, while trains run. And we also intend to investigate its effect on stabilization of the blending, fluctuation of catenary voltage and various electric equipments.

• Journal of Chest Surgery
• /
• v.27 no.4
• /
• pp.331-334
• /
• 1994

Pneumatic rupture is a rare cause of esophageal injury, as evidenced by only 19 cases reported in the literature. We experienced one case of esophageal rupture due to bursting of a truck inner tube. The patient, who was a 45-year old male, had severe chest pain, respiratory distress, flushing in the face and neck, and subcutaneous emphysema after tire explosion. Three days after the incident, a diagnosis of rupture of the thoracic esophagus was established by esophagogram using water soluble contrast media, and then emergency operation was done. The operation involved mediastinal and thoracic drainage and resection of the esophagus combined with cervical esophagostomy and feeding gastrostomy. On the 105th day after the operation, cervical esophagogastrostomy via substernal route was performed. The patient was successfully treated with the staged operations. As in the other reported cases, the injury was located in the lower one third of the esophagus. Four main characteristics of the clinical signs of pneumatic rupture are 1] wounds or burns to the face or mouth, 2] chest pain or epigastric pain, 3] subcutaneous emphysema, and 4] respiratory distress. We emphasize that the high index of suspicion of esophageal rupture is very important in diagnosis and that diagnosis should be based on the same findings common to other forms of esophageal injury.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.607-614
• /
• 1996

A computer vision based automatic intelligent sorting system for dried oak mushrooms has been developed. The developed system was composed of automatic devices for mushroom feeding and handling, two sets of computer vision system for grading , and computer with digital I/O board for PLC interface, and pneumatic actuators for the system control. Considering the efficiency of grading process and the real time on-line system implementation, grading was done sequentially at two consecutive independent stages using the captured image of either side. At the first stage, four grades of high quality categories were determined from the cap surface images and at the second stage 8 grades of medium and low quality categories were determined from the gill side images. The previously developed neuro-net based mushroom grading algorithm which allowed real time on-line processing was implemented and tested. Developed system revealed successful performance of sorting capability of approximate y 5, 000 mushrooms/hr per each line i.e. average 0.75 sec/mushroom with the grading accuracy of more than 88%.

• Pediatric Gastroenterology, Hepatology & Nutrition
• /
• v.25 no.4
• /
• pp.300-311
• /
• 2022

Purpose: Dysphagia, vomiting and feeding difficulties are common symptoms, with which children present. Esophageal function testing with high resolution manometry can help in diagnosing and treating these patients. We aim to access the clinical utility of high-resolution manometry of esophagus in symptomatic pediatric patients. Methods: A retrospective chart review was done on all symptomatic patients who underwent esophageal high-resolution manometry between 2010 and 2019 at Sydney Children's Hospital, Australia. Manometry results were categorized based on Chicago classification. Demographic data, indication of procedure, manometric findings, and details of treatment changes were obtained and analyzed. Results: There were 62 patients with median age of 10 years (9 months-18 years). The main indication for the procedure was dysphagia (56%). Thirty-two percent of patients had a co-morbid condition, with esophageal atresia accounting for 16%. The majority (77%) of patients had abnormal manometry which included, ineffective esophageal motility in 45.2%. In esophageal atresia cohort, esophageal pressurization was seen in 50%, aperistalsis in 40% and 10% with prior fundoplication had esophago-gastric junction obstruction. Patients with esophago-gastric junction obstruction or achalasia were treated by either pneumatic dilation or Heller's myotomy. Patients with ineffective esophageal motility and rumination were treated with a trial of prokinetics/dietary texture modification and diaphragmatic breathing. Conclusion: Esophageal high-resolution manometry has a role in the evaluation of symptomatic pediatric patients. The majority of our patients had abnormal results which led to change in treatments, with either medication, surgery and/or feeding modification with resultant improvement in symptoms.