• Journal of the Korean Wood Science and Technology
• /
• v.47 no.4
• /
• pp.425-441
• /
• 2019

In this study, sound absorption capability and sound transmission loss of several kinds of target densities and thickness for six species of wood bark particle were estimated by the transfer function and transfer matrix methods. Resultantly, the mean sound absorption coefficient of a 100-mm thick Hinoki wood bark particle mat was 0.90 in the frequency range of 100-6400 Hz, whereas the mean sound absorption rate of a 50-mm thick Hinoki wood bark particle mat was 0.84 in the same frequency range. Particularly, at a thickness of 100 mm, it reached almost up to 100% in the frequency range of 1 KHz. The sound transmission losses of 100-mm thick Hinoki wood bark particle mat with a target density of 0.16 at 500 and 1000 Hz were 15.30 and 15.73 dB, respectively. When a 10-mm thick plywood was attached to the back of the wood particle mat, the sound transmission losses was increased by 20-30 dB. Wood bark can be used as an acoustical material owing to its high sound absorption rate and transmission loss.

• Journal of the Society of Naval Architects of Korea
• /
• v.59 no.4
• /
• pp.207-213
• /
• 2022

LNG CCS which is a special type of cargo hold operated at -163℃ for transporting liquefied LNG is composed of a primary barrier, plywood, insulation panel, secondary barrier, and mastic. Currently, glass fiber is used to reinforce polyurethane foam. In this paper, we evaluated the possibility of replacing glass fiber-reinforced polyurethane foam with basalt fiber-reinforced polyurethane foam. We conducted a thermal conductivity test to confirm thermal performance at room temperature. To evaluate the mechanical properties between basalt and glass-fiber-reinforced polyurethane foam which is fiber content of 5 wt% and 10 wt%, tensile and an impact test was performed repeatedly. All of the tests were performed at room temperature and cryogenic temperature(-163℃) in consideration of the temperature gradient in the LNG CCS. As a result of the thermal conductivity test, the insulating performance of glass fiber reinforced polyurethane foam and basalt fiber reinforced polyurethane foam presented similar results. The tensile test results represent that the strength of basalt fiber-reinforced polyurethane foam is superior to glass fiber at room temperature, and there is a clear difference. However, the strength is similar to each other at cryogenic temperatures. In the impact test, the strength of PUR-B5 is the highest, but in common, the strength decreases as the weight ratio of the two fibers increases. In conclusion, basalt fiber-reinforced polyurethane foam has sufficient potential to replace glass fiber-reinforced polyurethane foam.

• Journal of the Korean Wood Science and Technology
• /
• v.2 no.4
• /
• pp.4-14
• /
• 1974

The total forest land area in Korea accounts for some 67 percent of the nation's land total. Its productivity, however, is very low. Consequently, forest production accounts for only about 2 percent of the gross national product and a minor proportion of no more than about 5 percent versus primary industry. In this case, however, only the direct income from forestry is taken into account, making no reference to the forestry output induced by other industrial sectors. The value added Or the induced forestry output in manufacturing the primary wood products into higher quality products, makes a larger contribution to the economy than direct contribution. So, this author has tried to analyze the structure of forestry and compute the repercussion effect and the induced output of primary forest products when utilized by other industries for their raw materials, Hsing the input-output table and attached tables for 1963 and 1966 issued by the Bank of Korea. 1. Analysis of forestry structure A. Changes in total output Durng the nine-year period, 1961-1969, the real gross national product in Korea increased 2.1 times, while that of primary industries went up about 1. 4 times. Forestry which was valued at 9,380 million won in 1961, was picked up about 2. 1 times to 20, 120 million won in 1969. The rate of the forestry income in the GNP, accordingly, was no more than 1.5 percent both in 1961 and 1962, whereas its rate in primary industries increased 3.5 to 5.4 percent. Such increase in forestry income is attributable to increased forest production and rise in timber prices. The rate of forestry income, nonetheless, was on the decrease on a gradual basis. B. Changes in input coefficient The input coefficient which indicates the inputs of the forest products into other sectors were up in general in 1966 over 1963. It is noted that the input coefficient indicating the amount of forest products supplied to such industries closely related with forestry as lumber and plywood, and wood products and furniture, showed a downward trend for the period 1963-1966. On the other hand, the forest input into other sectors was generally on the increase. Meanwhile, the input coefficient representing the yolume of the forest products supplied to the forestry sector itself showed an upward tendency, which meant more and more decrease in input from other sectors. Generally speaking, in direct proportion to the higher input coefficient in any industrial sector, the reinput coefficient which denotes the use of its products by the same sector becomes higher and higher. C. Changes in ratio of intermediate input The intermediate input ratio showing the dependency on raw materials went up to 15.43 percent m 1966 from 11. 37 percent in 1963. The dependency of forestry on raw materials was no more than 15.43 percent, accounting for a high 83.57 percent of value added. If the intermediate input ratio increases in any given sector, the input coefficient which represents the fe-use of its products by the same sector becomes large. D. Changes in the ratio of intermediate demand The ratio of the intermediate demand represents the characteristics of the intermediary production in each industry, the intermediate demand ratio in forestry which accunted for 69.7 percent in 1963 went up to 75.2 percent in 1966. In other words, forestry is a remarkable industry in that there is characteristics of the intermediary production. E. Changes in import coefficient The import coefficient which denotes the relation between the production activities and imports, recorded at 4.4 percent in 1963, decreased to 2.4 percent in 1966. The ratio of import to total output is not so high. F. Changes in market composition of imported goods One of the major imported goods in the forestry sector is lumber. The import value increased by 60 percent to 667 million won in 1966 from 407 million won in 1963. The sales of imported forest products to two major outlets-lumber and plywood, and wood products and furniture-increased to 343 million won and 31 million won in 1966 from 240million won and 30 million won in 1963 respectively. On the other hand, imported goods valued at 66 million won were sold to the paper products sector in 1963; however, no supply to this sector was recorded in 1963. Besides these major markets, primary industries such as the fishery, coal and agriculture sectors purchase materials from forestry. 2. Analysis of repercussion effect on production The repercussion effect of final demand in any given sector upon the expansion of the production of other sectors was analyzed, using the inverse matrix coefficient tables attached to the the I.O. Table. A. Changes in intra-sector transaction value of inverse matrix coefficient. The intra-sector transaction value of an inverse matrix coefficient represents the extent of an induced increase in the production of self-support products of the same sector, when it is generated directly and indirectly by one unit of final demand in any given sector. The intra-sector transaction value of the forestry sector rose from 1.04 in 1963 to 1, 11 in 1966. It may well be said, therefore, that forestry induces much more self-supporting products in the production of one unit of final demand for forest products. B. Changes in column total of inverse matrix coefficient It should be noted that the column total indicates the degree of effect of the output of the corresponding and related sectors generated by one unit of final demand in each sector. No changes in the column total of the forestry sector were recorded between the 1963 and 1966 figures, both being the same 1. 19. C. Changes in difference between column total and intra-sector transaction amount. The difference between the column total and intra-sector transaction amount by sector reveals the extent of effect of output of related industrial sector induced indirectly by one unit of final demand in corresponding sector. This change in forestry dropped remarkable to 0.08 in 1966 from 0.15 in 1963. Accordingly, the effect of inducement of indirect output of other forestry-related sectors has decreased; this is a really natural phenomenon, as compared with an increasing input coefficient generated by the re-use of forest products by the forestry sector. 3. Induced output of forestry A. Forest products, wood in particular, are supplied to other industries as their raw materials, increasng their value added. In this connection the primary dependency rate on forestry for 1963 and 1966 was compared, i. e., an increase or decrease in each sector, from 7.71 percent in 1963 to 11.91 percent in 1966 in agriculture, 10.32 to 6.11 in fishery, 16.24 to 19.90 in mining, 0.76 to 0.70 in the manufacturing sector and 2.79 to 4.77 percent in the construction sector. Generally speaking, on the average the dependency on forestry during the period 1963-1966 increased from 5.92 percent to 8.03 percent. Accordingly, it may easily be known that the primary forestry output induced by primary and secondary industries increased from 16, 109 million won in 1963 to 48, 842 million won in 1966. B. The forest products are supplied to other industries as their raw materials. The products are processed further into higher quality products. thus indirectly increasing the value of the forest products. The ratio of the increased value added or the secondary dependency on forestry for 1963 and 1966 showed an increase or decrease, from 5.98 percent to 7.87 percent in agriculture, 9.06 to 5.74 in fishery, 13.56 to 15.81 in mining, 0.68 to 0.61 in the manufacturing sector and 2.71 to 4.54 in the construction sector. The average ratio in this connection increased from 4.69 percent to 5.60 percent. In the meantime, the secondary forestry output induced by primary and secondary industries rose from 12,779 million Wall in 1963 to 34,084 million won in 1966. C. The dependency of tertiary industries on forestry showed very minor ratios of 0.46 percent and 0.04 percent in 1963 and 1966 respectively. The forestry output induced by tertiary industry also decreased from 685 million won to 123 million won during the same period. D. Generally speaking, the ratio of dependency on forestry increased from 17.68 percent in 1963 to 24.28 percent in 1966 in primary industries, from 4.69 percent to 5.70 percent in secondary industries, while, as mentioned above, the ratio in the case of tertiary industry decreased from 0.46 to 0.04 percent during the period 1963-66. The mining industry reveals the heaviest rate of dependency on forestry with 29.80 percent in 1963 and 35.71 percent in 1966. As it result, the direct forestry income, valued at 8,172 million won in 1963, shot up to 22,724 million won in 1966. Its composition ratio lo the national income rose from 1.9 percent in 1963 to 2.3 per cent in 1966. If the induced outcome is taken into account, the total forestry production which was estimated at 37,744 million won in 1963 picked up to 105,773 million won in 1966, about 4.5 times its direct income. It is further noted that the ratio of the gross forestry product to the gross national product. rose significantly from 8.8 percent in 1963 to 10.7 percent in 1966. E. In computing the above mentioned ratio not taken into consideration were such intangible, indirect effects as the drought and flood prevention, check of soil run-off, watershed and land conservation, improvement of the people's recreational and emotional living, and maintenance and increase in the national health and sanitation. F. In conclusion, I would like to emphasize that the forestry sector exercices an important effect upon the national economy and that the effect of induced forestry output is greater than its direct income.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.4 no.1
• /
• pp.1-10
• /
• 1984

This dissertation presents an exact solution for the shearing and normal stresses of an orthotropic plane body loaded by a pairtial-uniform shear load. The solution satisfies the equilibrium and compatibility equations concurrently. An Airy stress function is introduced to solve the problem related to an orthotropic half-infinite plane under a partial-uniform shear load. All the equations for orthotropy must be degenerated into the expressions for isotropy when orthotropic constants are replaced by isotropic ones. The author has evaluated all the equations of orthotropy and succeeded in obtaining exactly identical expressions to the equations of isotropy which were derived independently by means of L'hospital's rule. The analytical results of, isotropy ate compared with the simple results of other investigator. Since a concentrated shear load is a particular case of partial-uniform shear load, all the equations of partial-uniform shear load case are degenerated into the expressions for concentrated load case of isotropy and orthotropy. The formal solution is expressed in terms of closed form. The numerical results for orthotropy are evaluated for two kinds and two different orientations of the grain of wood. The type of wood considered are three-layered plywood and laminated delta wood. The distribution of normal and shearing stresses are shown in figures. It is noted that the distribution of stresses of orthctropic materials dependson the type of materials and orientations of the grain.

• Journal of the Korean Wood Science and Technology
• /
• v.10 no.3
• /
• pp.118-131
• /
• 1982

1. In order to investigate the effect of variation of assembly time on glue bond strength, and to determine the optimum range of assembly time with given glue, this experiment was made at the suggestion of the Wood Technology Laboratory, School of Forestry, Yale University. 2. For this investigation, three-ply-plywoods with 1/22 inch, birch veneer, phenolic resin, and soybean glue were made at the following variation of assembly time, that is, 1, 5, 10, 25, 35, 50, and 70 minutes, under both open and closed assembly manners, and the shear strength test at dry and wet were adoptted. 3. The shear strength and wood failure of each plywood panel constructed at the given assembly time have been illustrated in Tables 1, 2, 3 and 4. It has shown that there is a remarkable tendency, for increasing assembly time to give lower shear strength and wood failure throughout almost all cases. The effective range of assembly time of tested glues in this investigation for both open and closed assembly are summarized in the Table 7. Thus, allowable assembly time for Phenolic resin may be up to 10 minutes under open assembly and up to 50 minutes under closed assembly. For soybean glue, the permissible assembly time may be up to 5 minutes under open assembly and up to 15 minutes under closed assembly. The allowable assembly time for open assembly with the same glue is reduced by approximately one third or more than one third as compared with closed assembly time. This might mean that the closed asembly time for these glues is more practical than the open assembly.

• The Journal of Art Theory & Practice
• /
• no.6
• /
• pp.77-99
• /
• 2008

The purpose of this study is to show that the reason behind the ambivalent characteristic displayed in Niki de Saint Phalle's works is in her trauma and how such characteristic can be extracted from her works. During her creative years, Saint Phalle worked on various materials from different genres such as assemblages, shooting paintings, a series on Bride and Monster, 'Nana', 'Tarot Garden'and public sculptures. One commonality found among her various works is the ambivalent characteristic that contains contrasting elements simultaneously. Saint Phalle suffered a terrible psychological damage inflicted by her parents during her childhood. Specifically, she was sexually assaulted by her father and emotionally neglected by her mother, the trauma that affected her for the rest of her life. As a result, she came to develop extreme love- hate relationships with her parents and this became the main reason for the ambivalent characteristic displayed in her works. The love-hate relationship Saint Phalle developed can be identified through various researches done on the subject of the affect of sexual assault. It is common for incest victims to develop ambivalent feelings towards the perpetrator and Saint Phalle was no exception. Dissociation disorder and a snake well explain the trauma from her father. It is a generally accepted belief in the field of psychology that dissociation disorder commonly occurs to children who experience incest. And dissociation disorder is similar to the characteristic of ambivalence in the sense that a single entity contains more than two contrasting elements at the same time. In addition, the amputated doll objects used in her assemblages coincide with the expression of body detachment of people with dissociation disorder. These facts clearly indicate that the trauma from her father is showing through in her works. A snake is a subject matter that reflects the ambivalent tendency of Saint Phalle that resulted from her trauma. She remembers her father's rape as an image of a snake which is related to a phallic symbol in mythology or art reflecting her trauma. Moreover, she displays a similar pattern of ambivalent emotion like love and hate or fear towards a snake and her father. This is also confirmed by her portrayal of a snake as a monster or reversely as a creature with fundamental vitality in her works. The lack of affection from her mother can be explained by her mother's maternal deprivation. It appears that Saint Phalle's mother possessed all the causes for maternal deprivation such as maternal separation, personality disorder and inappropriate attitude towards child rearing. Especially, a study that shows mother's negative attitude towards child breeding tends to increase dissociation experience of children is another important evidence that supports Saint Phalle's dissociation tendency. These traces of Saint Phalle's trauma are clearly revealed in her assemblages and shooting paintings. The violent objects in her assemblages such as a hammer, razor, nail represent the rage and defensiveness towards her father. The objects such as fragments of broken plates of feminine patterns, pots and mirrors that her mother used symbolize the affection towards her mother. On the other hand, the destructed objects can be interpreted as her hate and resentment towards her mother. Shooting paintings contain her extreme fury and hate. Things such as acts of shooting and the image associated with blood after shooting are blunt expressions of her bursts of emotions. I have tried to define and classify the ambivalent characteristics shown in her assemblages and shooting paintings as hate, rage, violence, calm, love and pleasure according to the frame of Thanatos and Eros. Out of the six, hate, rage, violence and clam are associated with Thanatos while love and pleasure are associated with Eros and they correspondingly form an ambivalent structure. These ambivalent characteristics can be found in her assemblages and shooting paintings. The objects in her assemblages such as a razor, saw, hammer imply hate, rage, violence and the silence felt throughout her works represent calmness. And, as mentioned, the feminine objects can be seen as symbolizing love. In shooting paintings, hate, rage, violence can be found in the use of force and in the traces of watercolor after shooting, and a sense of pleasure in her feelings of catharsis after her shooting. Moreover, a shielded calmness can be found on the plywood all covered with plaster before the shooting. This study looked into the ambivalent characteristic of Saint Phalle's works by examining her trauma to find its correlation, and a meaning of this study can be found from the fact that it refocused the origin of Saint Phalle who is generally known as a feminist artist. Additionally, a meaning of the study can be found also from the fact that it examined the ambivalent characteristics of her works through a frame of Thanatos and Eros.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.3
• /
• pp.374-380
• /
• 2015

The quality characteristics of the woodpellet manufactured from two domestic pines (Pinus densiflora S. et Z. and Pinus rigida Mill.) were investigated for the efficient energy use of woody biomass resources. Properties of woodpellets such as moisture content, heating value, ash content, apparent density and durability were determined by using the standard test method of woodpellets of Korea Forest Research Institute (KFRI) and elemental analysis. The results of elemental analysis for C, H, O and N showed 61.42% carbon, 5.56% hydrogen, 32.87% oxygen, and 0.15% nitrogen for Pinus densiflora S. et Z. and 61.03% carbon, 5.96% hydrogen, 32.83% oxygen, and 0.18% nitrogen for Pinus rigida Mill. No significant difference between Pinus densiflora S. et Z. and Pinus rigida Mill was observed on elemental analysis. Heating values of each woodpellet were ranged from 19.00 to 19.42 MJ/kg which satisfied the first grade quality standard (${\geq}18.0MJ/kg$) by KFRI. The ash contents of woodpellet were slightly different between Pinus densiflora S. et Z. and Pinus rigida Mill., and satisfied the first grade quality standard (${\leq}0.7%$) by KFRI. Apparent density of woodpellet (Pinus densiflora S. et Z.) was passed the first grade standard level (${\geq}640kg/m^3$), and woodpellets from Pinus rigida Mill. satisfied the second grade quality of the standard. The moisture contents of each woodpellet were satisfied by the first grade quality standard (${\leq}10%$). The durability of woodpellet (Pinus densiflora S. et Z.) was passed the third grade level (${\geq}95%$), but Pinus rigida Mill. woodpellet was insufficient to satisfy the quality standard.

• Journal of Preventive Medicine and Public Health
• /
• v.19 no.1 s.19
• /
• pp.16-30
• /
• 1986

In order to prepare the fundamental data for the improvement of noisy working environments and the effective hearing conservation program on workers exposed to industrial noise, the authors surveyed the working processes and evaluated the noise levels on 56 manufacturing industries in Pusan area from April to July in 1985. The results were summarized as follows : 1. The noise level was the highest in shipbuilding and repairing(95.6 dBA), and followed by steel rolling(94.0 dBA), manufacture of motor vehicles(93.1 dBA), manufacture of fishing nets(92.9 dBA), manufacture of testiles(92.5 dBA), iron and steel foundries(89.3 dBA), manufacture of metal products(89.1 dBA), preserving and processing of marine foods(87.0 dBA), manufacture of rubber products(85.3 dBA), manufacture of plywood(84.9 dBA) and manufacture of paints(84.5 dBA). 2. Among fifty surveyed working processes, the noise level of twenty-one processes (42%) exceeded the threshold limit value for 8 hours per day. 3. As the allowable exposure times by governmental threshold limit values to industrial noise level(dBA), cocking of shipbuilding and repairing and plating(CGL) of steel rolling were the shortest(30 minutes), and followed by assembling(rivet) of manufacture of motor vehicles(1 hour) weaving of manufacture of textiles and shot, machine, pipe laying of shipbuilding and repairing(2 hours). 4. By the result of octave band analysis on noisy working processes in excess of 90 dBA, the sound level was the highest at 2,000 Hz or 4,000 Hz. 5. It was recognized that the measurement of overall sound pressure level was also effective as octave band analysis in evaluating the industrial noise.

• Journal of the Korean Wood Science and Technology
• /
• v.12 no.1
• /
• pp.3-10
• /
• 1984

Taro-UF mixed type resin system was developed for gluing plywoods. The taro adhesive that was activated with sodium hydroxide was mixed with the definite ratios of UF resin adhesive. At the sametime, wheat-UF mixed type resin was also applied with the same method as taro-UF mixed type resin The mixing ratios of taro or wheat adhesive: UF resin were 0:100, 10:90, 20:80, 30:70, 40:60, 50:50, 60:40, 80:20, and 100:0 by weight. In addition, the UF resins extended with wheat powder at the extending ratios of wheat powder UF resin, 10:90, 20:80, 30:70, 40:60, and 50:50 by weight, were also used. The dry and wet shear strengths of the plywoods of 30:70 (taro adhesive : UF resin) mixing ratio were highest. The dry shear strengths of the plywoods manufactured with the UF resin-mixing taro adhesive were higher than those of the plywoods with the UF resin-mixing wheat adhesive at 10:90, 20:80, 30:70, 40:60, 50:50, and 60:40 (taro or wheat adhesive: UF resin) mixing ratios. At all mixing ratios, the wet shear strengths of the plywoods manufactured with the UF resin-mixing taro adhesive were higher than those of the plywoods with the UF resin-mixing wheat adhesive. The dry and wet shear strengths of the plywoods manufactured with the UF resin-mixing wheat adhesive were higher than those of the plywoods with the wheat powder-extending UF resin at the mixmg ratios, 10:90, 20:80, 30:70, and 40:60 (wheat adhesive or wheat powder: UF resin). So, it was found that the plywoods manufactured with the UF resin-mixing taro adhesive and the UF resin mixing wheat adhesive had better shear strength than the plywoods with the wheat powder-extending UF resin. It was because the taro adhesive and wheat adhesive themselves took the bonding properties after being activated with alkali.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.9 no.3
• /
• pp.215-221
• /
• 1976

In this study, noise arresting effect of the noise control room from the transmission of surrounding noise was tested when the packing noise control rooms were set up in the test room in which the prerecorded noise from an engine room was reradiated at the same level as the original pressure. The inner space of control room A is $3.389m^3(1.19\times1.19\times2.14m)$ having walls furnished with plywood board 9mm in thickness and noise control room door$(60\times45cm) $ and illumination lamp are placed. In case of the control room B, noise absorption board(10mm fiber board which holds the corntype concavity with diameter of 5mm, depth 5mm, space 15mm) is adhered to the internal ceiling and styrol foam boards(20mm) to the walls. The other struction is same as the control room A. Type C is the same as B except wool board(Glass Fiber, 33mm) on the walls. Type D is same as type A except that the thickness of wall is 12mm and wood pyramid type cone$(5\times5\times13cm)$ is adhered to the ceiling ana walls(Fig. 1). When the recorded noise and vibrated noise were controlled in various levels. The noise pressure which passed through the control rooms was measured by sound level meter(Bruel & Kjar 2205, measuring range 37-140dB). In order to calculate the absorption rate in the control rooms the noise pressure was measured at different distances when the recorded noise pressure was radiated. The followings are the results obtained from the experiment. 1. When the noise pressure of the test room was 60dB, transmission rate of type A was $69.7\%$ and increased $3.3\%$ per 10dB. At the same condition, the rate was $53.9\%$ and increased $4.5\%$ per 10dB in type D. Type D was the most effective in noise arresting of the four and the effect was D,C,B and A in order(Fig.2). 2. When the oscillator sound and vessels noise were radiated in 1,000Hz, at one meter distance to the type A and D, the oscillator sound pressure were 77dB and 73dB, while the vessels noise pressure were 73.3dB and 66.2dB respectivley(Fig.3). 3. Refering to the influence of the frequency to the lower oscillator sound(1,000Hz) pressure, both type C and D were almost same at 140cm but type C was 0.3dB lower than type D at 20cm distance(Fig.4).