• 한국자동차공학회논문집
• /
• 제10권5호
• /
• pp.121-128
• /
• 2002

In this paper, the fuel economy of plug-in type hybrid electric vehicle is investigated through simulation. For the simulation study, 2 shaft type parallel hybrid powertrain is chosen and its operation modes are described. The operation algorithm which yields operation points of minimal fuel cost is suggested. Dynamic model fur operation of HEV and simulation procedure is described. Simulation results of fuel economy is compared to non plug-in type HEV as well as conventional vehicle. With total driving distance of 37km and full usage of 2kwh of electric energy stored in battery pack, plug-in type HEV shows 28-30% improved fuel economy compared to non plug-in type HEV and 86-93% improved fuel economy compared to conventional vehicle.

• 오토저널
• /
• 제13권3호
• /
• pp.32-42
• /
• 1991

In SI engine research the pressure data in cylinder is the most important fundamental ones leading to engine efficiencies and performances. It is, therefore, necessary to obtain accurate pressure data and yet it is often impossible to install a reliable data producing, flush-mounted type pressure transducer in a cylinder of small and medium size multicylinder SI engines. When flush mounting the transducer is not possible, the spark-plug type pressure transducer is commonly used as an alternative. In this case, the transmission tube of spark-plug type pressure transducer introduces distortions in the pressure signal. Efforts were made to understand the dynamic characteristics of spark-plug pressure transducer by shock tube tests and real engine experiments. In engine experiment the cylinder pressure data were simultaneously obtained by both flush mounted and spark-plug type pressure transducers of certain transmission tube geometry. Those pressure data collected by spark-plug type pressure transducer were tested for correction to flush mounted ones by the application of transfer function. As a result of the calibration the IMEP difference between F/M data and improved S/P data was shown to be corrected about 75-98% from the original ones.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2001년도 춘계학술대회 논문집
• /
• pp.170-177
• /
• 2001

Since plug type passenger door has two motion modes, power transmission unit must be capable of plug-in or plug-out, and sliding mode. Complex planetary gear train is proposed, which is composed of two 2K-H, I type planetary gear units. For the proposed complex planetary gear train, ranges of addendum modification coefficients which would not lead to interferences is analyzed, and optimal addendum modification coefficients among these ranges which generate the maximum efficiency are presented. Based on the interference, efficiency and torque ratio analysis results, complex planetary new train is designed and manufactured.

• 한국철도학회논문집
• /
• 제4권2호
• /
• pp.55-61
• /
• 2001

Since the plug type passenger door has two modes of motion, a power transmission unit must be capable of plug-in or plug-out mode, and sliding mode. Complex planetary gear train is proposed, which is composed of two 2K-H, I type planetary gear units. For the proposed complex planetary gear train, ranges of addendum modification coefficients which would not lead to interferences are analyzed, and optimal addendum modification coefficients among these ranges which generate the maximum efficiency are presented. Based on the results of analysis on interferences, efficiencies and torque ratios, the specifications for the complex planetary gear train were determined. It has been shown by tests of the complex planetary gear train manufactured that the gear train worked well with good agreements of analysis.

• 한국방송∙미디어공학회:학술대회논문집
• /
• 한국방송공학회 2009년도 IWAIT
• /
• pp.794-798
• /
• 2009

We introduce an implementation of plug-ins on PLUTO. These plug-ins discriminate inflammatory nodules from other types of nodules in chest X-ray CT images. The PLUTO is a common platform for computer-aided diagnosis systems on Microsoft Windows series and it is easy to add new functions as plug-ins. We coded two plug-ins. One of the them calculates features based on medical knowledge. The other plug-in calculates parameters to classify the type of nodules, and it also classifies nodules into inflammatory nodules and others using SVM. These plug-ins are coded using MIST library which is produced at Nagoya University, Japan. In our previous study, the MIST library was parallelized, so that we can utilize a number of CPUs to calculate features and SVM learning/classifying depending on the amount of computation. Using these plug-ins, it became easy to extract features to discriminate inflammatory nodules from other types of nodules and to change parameters for feature extraction and SVM learning/classifying with GUI interface. The accuracy of the classifying result is 100% with 78 solid nodules which contains 43 inflammatory nodules and 35 other type of nodules.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2001년도 춘계학술대회 논문집
• /
• pp.162-169
• /
• 2001

There are many EMU lines in korea. But only one type has been applied to passenger side door. This type is so called "Pocket sliding type". This type has some week points. To begin with, it is not good for decreasing the noisy form the outside of carbody. And the second time, if some obstacles are put between sliding door, only driver can operate re-open door switch manually ill driver's cab. This type is so dangerous for passengers. So many people want to the new door type that have no defect. KRRI joined forces with ANT corporation for pneumatic plug door system. This type will be good for decreasing the noisy, passenger′s safe. The project was started at the last year on November and will be finished on June, this year In this paper, we will deal with the role of cylinder, planetary gear, door control unit, dynamic mechanism, and the report of FEM, type test. This paper will contribute to tile electric motor control plug door system.

• 한국분무공학회지
• /
• 제14권4호
• /
• pp.171-177
• /
• 2009

This study proposes a new stratified charge system for low emission and ultra lean burn. In order to examine combustion characteristics of the new system, sparkplug with a hole at positive pole and a common CNG injector for injecting fuel were used in this study as injector-type spark plug. The new stratified charge system injects fuel of extremely small quantities and ignites mixture around sparkplug gap. Also, the system was fitted in a visualized constant volume chamber. Then, for analysis of the combustion characteristics, we examined combustion pressure, lean inflammable limit, and visualized combustion flame according to equivalence ratio by comparison with homogeneous charge (HC) method and the new stratified charge (SC) method. As results of this study, in the case of using this system, the propagation speed of initial flame was increased and total combustion period was reduced in the ultra lean burn in the same equivalence ratio. These phenomena occurred clearly under the conditions of lean equivalence ratio. Furthermore, the lean inflammable limit of mixture was extended by using the injector-type spark plug.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2004년도 추계 학술대회논문집
• /
• pp.29-32
• /
• 2004

A three dimensional numerical analysis and experimental measurements were made for incompressible flows in a globe valve with three different types of plug. Characteristics of pressure drop across the valve were investigated for each type of plug at various opening positions. Numerical simulation results show a good agreement with experimental data.

• 한국IT서비스학회지
• /
• 제12권4호
• /
• pp.449-459
• /
• 2013

The software which is used for electronic bulletin boards have shortcomings that the addition of new function and new information's type to the order point software is very difficult, and the aggressive adaption of newly introduced type of media is impossible because the software is developed by custom solution. Eventually new cost and time are required to enhance functionality or performance to software of DID(Digital Information Display). In this paper, we proposed the scheme to package DID's contents and to customize it using plug-in method. We conducted a case study of this scheme. The platform which can install Apps to DID as one of content was designed. Apps can be inserted by plug-in type on DID platform and run separately with DID framework. As a result, We got advantage that various contents, functions and Apps which are drived on Android can be displayed without any restriction and dependency because Apps itself is one of dynamic notice object. This solution increase reusability of Apps or contents, and can be used easily in various places such as airports, stations, terminals, and front desk by customizing.

• 한국자동차공학회논문집
• /
• 제23권1호
• /
• pp.112-121
• /
• 2015

In this paper, powertrain of output split type plug-in hybrid electric vehicle is analyzed for the operation range of speed, torque, and power. First, it is assumed that the efficiency of motor is 100%. And, the speed and torque equations are derived based on the lever analogy. With the above equations, the simulations are performed for the powertrain of output split type plug-in hybrid electric vehicle. From the simulation results, it is found that the output torques of EV1 and series modes are larger than the EV2 and power split modes' ones. It means the EV1 and series modes can be used for the rapid acceleration. But the EV1 and series modes can be used only the velocity of under the 120 km/h. It is because the motor reaches its maximum speed when the velocity is over the 120 km/h for the EV1 and series modes. When the engine is turned on, the engine power is transmitted through the two motors. But, the power split mode shows the power split of engine at the output shaft, and it has the point of zero motor power. Thus, the transmission efficiency of the power split mode can be higher than the series mode's one, it the motor efficiency is considered.