Transactions of the Society of Information Storage Systems
/
v.2
no.3
/
pp.184-188
/
2006
In recent years the flying height of the head/slider has been decreasing in order to increase the recording density of hard disk drive (HDD). Accordingly, it was predicted that direct contact between slider and disk surface (slider slap) can cause defects on the disk such as scratch and particle generation. In this work, we theoretically demonstrate the effect of rounded-edge slider using Hertzian contact theory. Depth and width of scratch were predicted by plowing model. Furthermore, as we fabricated rounded-edge slider, rounded-edge slider was tested and compared with sharp-edge slider. The experimental results show rounded-edge was effective for reducing scratch depth.
Transactions of the Korean Society of Mechanical Engineers
/
v.18
no.10
/
pp.2597-2605
/
1994
The wear behavior of two types of $Si_3N_4$ exposed to high and low humidity was examined at various sliding speeds, using bearing steel as disk material under pin-on-disk type sliding conditions. Higher wear rates were obtained at a high humidity than at a low humidity. As the sliding speed was increased, the wear rates were decreased and the effect of humidity on the wear rates of $Si_3N_4$ was reduced. The result that the $Si_3N_4$ pin showed higher wear rate under the high humidity condition was explained by the decrease in microhardness of $Si_3N_4$ due to the chemisorbed moisture on the pin and plowing action by the hard particles of $Fe_2O_3$ from the disk. An increase in the sliding speed is supposed to reduce the effect of humidity on the wear rate of $Si_3N_4$ by raising the average temperature of the disk surface and the local temperature at pin-disk contact point.
This experiment was carried out to evaluate the effect of improvement of soil physical property such as deep plowing and chiseling and diagnostic application of N, P, K fetilizers. Latex Coated Urea(LCU), compost, sillicate for increasing yielding and enchancing N-use efficiency in puddled-soil drill seeding of Rice. The soil physical properties, such as bulk density, hardness and porosity were increased by deep plowing and chiseling, as well as chemical propeties were highly enhanced soil productivity due to increase the content of organic matter, available $P_2O_5$ and K as compare with control. The amount of $NH_4-N$ in soil was highly increased by diagnostic fertilization and chiseling, while recovery rate of V fertilizer was the highest at LCU 80% applied with chiseling. The rice yield increased by 23% under the diagnositic application of LCU 80% applied base with chiseling.
Fields experiments were conducted to investigate the effect of various tillage depth (TD) on productivity and quality of C. auriculatum Royle ex Wight from 2005 to 2006. The length of vine was elongated in lower TD treatments as 50 cm longer in 10 cm TD than 30 cm TD, and stem diameter and dry weight had increased in the lower TD. Length, width, and weight of leaves showed the quantitive growth in the lower TD treatments, but the chlorophyll content had increased in the deeper TD treatments. Root number and length had increased in the deeper TD treatments, but the root diameter and decomposed root was increased in the deeper TD. The total yield of root showed the increasing tendency in the deeper TD treatments as 6.2 ton/ha in 10 cm TD and increased as $7{\sim}9%$ in the 20 cm TD treatments.
Nano/micro friction with the contact area was studied on Si-wafer (100) and diamond-like carbon (DLC) film. Borosilicate balls of radii $0.32{\mu}m,\;0.5{\mu}m,\;1.25{\mu}m\;and\;2.5{\mu}m$ mounted on the top of AFM tip (NPS) were used for nano-scale contact and Soda Lime glass balls of radii 0.25mm, 0.5mm, 1mm were used for micro-scale contact. At nano-scale, the friction between ball and surface was measured with the applied normal load using an atomic force microscope (AFM), and at micro scale it was measured using ball-on flat type micro-tribotester. All the experiments were conducted at controlled conditions of temperature $(24\pm1^{\circ}C)$ and humidity $(45\pm5\%)$. Friction was measured as a function of applied normal load in the range of 0-160nN at nano scale and in the range of $1000{\mu}N,\; 1500{\mu}N,\;3000{\mu}N\;and\;4800{\mu}N$ at micro scale. Results showed that the friction at nano scale increased with the applied normal load and ball size for both kinds of samples. Similar behavior of friction with the applied normal load and ball size was observed for Si-wafer at micro scale. However, for DLC friction decreased with the ball size. This difference of in behavior of friction in DLC nano- and microscale was attribute to the difference in the operating mechanisms. The evidence of the operating mechanisms at micro-scale were observed using scanning electron microscope (SEM). At micro-scale, solid-solid adhesion was dominant in Silicon-wafer, while plowing in DLC. Contrary to the nano scale that shows almost a wear-less situation, wear was prominent at micro-scale. At nano- and micro-scale, effect of contact area on the friction was discussed with the different applied normal load and ball size.
Kim, Min-Kyeong;Jung, Goo-Bok;Kim, Min-Young;Kim, Myung-Hyun;Cho, Kwang-Jin;Choi, Soon-Kun;Hong, Seong-Chang;So, Kyu-Ho
Korean Journal of Environmental Agriculture
/
v.33
no.2
/
pp.144-147
/
2014
BACKGROUND: It is essential to prioritize the exact and clear understanding of agricultural nonpoint source pollution (NPS) controls. The realistic policies and systems should also be developed based on this understanding. Therefore, this study aimed to present agricultural Best Management Practices (BMPs) applicable for the fields based on the Delphi survey result. METHODS AND RESULTS: This study deduced the evaluation items to assess each BMP for agricultural NPS control and conducted the surveying using the Delphi method based on agricultural BMP experts. In addition, its on-the-spot application were evaluated. Considering its importance, technical, social and economic proprieties showed that political support was ranked first and followed by cost investment, labor investment, reduction effect and resident participation. The survey findings by agricultural BMP experts showed the good performance of on-the-spot application can be achieved from fertilization by soil testing, residue and green manure application and contour plowing which are applicable within a field. Agricultural BMPs, highly applicable for the fields, were the countermeasures that farmers who are the principal bodies of agricultural NPS control could be participated directly. CONCLUSION: The active participation of farmers is essential for effective control of agricultural NPS. It is necessary to establish various incentive systems.
Four different paddy soils collected around the Gyeongju nuclear site were treated with $^{99}TcO_4{^-}$ solution under the assumption of two contrasting contamination scenarios. Scenario I (SN-I) is for a pre-transplanting deposition of $^{99}Tc$ followed by plowing, whereas SN-II is for its deposition onto the water surface shortly after transplanting. Rice plants were grown in lysimeters in a greenhouse. Plant uptake of $^{99}Tc$ was quantified with the $TF_{area}$ ($m^2{\cdot}kg^{-1}-dry$). The SN-II $TF_{area}$ values for straws and brown rice, having been generally higher than the SN-I values, were within the ranges of $6.9{\times}10^{-3}{\sim}4.1{\times}10^{-2}$ and $5.2{\times}10^{-6}{\sim}7.3{\times}10^{-5}$, respectively. Sorption onto clay seems to have decreased $^{99}Tc$ uptake in SN-I, whereas it may have had an insignificant effect in SN-II. A phenomenon characteristic of submerged paddy soil, i.e., the development of a thin oxic surface layer may have greatly affected the rice uptake of SN-II $^{99}Tc$. The surface-water concentrations of $^{99}Tc$ were much higher in SN-II than in SN-I. For the percolating water, however, the opposite was generally true. At most 1.3% of the applied $^{99}Tc$ were leached through such percolation. The use of empirical deposition time-dependent $TF_{area}$ values was considered desirable in assessing the radiological impact of a growing-season deposition of $^{99}Tc$ onto paddy fields.
Kim, Ki-Hoon;Kang, Nae-Kyu;Song, Uh-Ram;Lee, Eun-Ju
Journal of Environmental Science International
/
v.21
no.2
/
pp.181-188
/
2012
Salicornia europaea (glasswort) is succulent, annual, halophytic plant mainly distributed throughout reclaimed land or salt marsh. It has strong tolerance to salt so that it plays the part of the pioneer species in the first succession. According to domestic and foreign studies, S. europaea contains plenty of minerals and antioxidant in the body. Since people take note of an availableness of this plant as health diet, the natural growth sites are threatened. In addition to development of salt marsh and sea shore, imprudent harvest has a bad effect to S. europaea population maintenance. To seek ways to preserve the population of this plant, we carried out the continuity of seed germination and restoration test. Seokmo Island, Daebu Island, Youngjong Island and Sudokwon landfill in Korea are selected sites for research. Result of germination continuity shows that most S. europaea seeds germinate on March but no more after July. However the germination was occurred after that time in the greenhouse. So we concluded that no germination after July is a matter of environmental condition not the number of remaining seeds. Also germination was seldom occurred in the spot where seeds production was not happened. In result of continuity test of seed germination by soil depth, germination was occurred vigorously only in top soil. From these results, we note that most S. europaea germinate in the early spring, and germination is finished by July. And this rapid germination speed makes the number of seeds in soil seed bank rare. If a large number of S. europaea in some area are harvested after July, the number of this species will dramatically decrease in that area the following year. In Seokmo Island, we carried out reintroduction experiment by sowing S. europaea seeds. On the first year, a small number of S. europaea settled and they produced seeds successfully. On April 2010, the second year, we observed many S. europaea in seed sowing sites. And we found out that plowing is more efficient than treatment sea water for settlement of S. europaea.
Nitrogen fertilizer is an essential macronutrient that requires repeated input for crop cultivation. Excessive use of nitrogen fertilizers can adversely affect the environment by discharging NH3, NO, and N2O into the air and leaching into surrounding water systems through rainfall runoff. Therefore, it is necessary to develop a technology that reduces the amount of nitrogen fertilizer used without compromising crop yields. Fertilizer deep placement could be a technology employed to increase the efficiency of nitrogen fertilizer use. In this study, a deep fertilization device that can be coupled to a tractor and used to inject fertilizer into the soil was developed. The deep fertilization device consisted of a tractor attachment part, fertilizer amount control and supply part, and an underground fertilizer input part. The fertilization depth was designed to be adjustable from the soil surface down to a depth of 40 cm in the soil. This device injected fertilizer at a speed of 2,000 m2/hr to a depth of 25 to 30 cm through an underground fertilizer injection pipe while being attached to and towed by a 62-horsepower agricultural tractor. Furthermore, it had no difficulty in employing various fertilizers currently utilized in agricultural fields, and it operated well. It could also perform fertilization and plowing work, thereby further simplifying agricultural labor. In this study, a newly developed device was used to investigate the effects of deep fertilizer placement (FDP) compared to those with urea surface broadcasting, in terms of rice and soybean grain yields. FDP increased the number of rice grains, resulting in an average improvement of 9% in rice yields across three regions. It also increased the number of soybean pods, resulting in an average increase of 23% in soybean yields across the three regions. The results of this study suggest that the newly developed deep fertilization device can efficiently and rapidly inject fertilizer into the soil at depths of 25 to 30 cm. This fertilizer deep placement strategy will be an effective fertilizer application method used to increase rice and soybean yields, in addition to reducing nitrogen fertilizer use, under conventional rice and soybean cultivation conditions.
Magazine of the Korean Society of Agricultural Engineers
/
v.13
no.1
/
pp.2162-2176
/
1971
From the ancient times our forefathers settled down in this peninsular and cultivated the hills and waste-lands into fields. Instead of fertilizing the lands they moved to find other fertile lands and lived a feudal life of agriculture and various machines played a main role in the land reclamation. The best method of land clearing, the time and efficiency in the operation and the effect of growing crops should sysematically analized prior to the time of 3rd Five-year Economic Development(1972-1976) in order to cultivated 210,000 ha of waste-land or the modernization of our country. The present study was investigated to find out a new working-system of mechanical land clearing and development of fertile soil. The results are as follows: 1) The land reclamation in natural slope is much more encourageable in land clearing and farming when the slope is below ten grades than bench terrace. 2) Weeds were mixed with soil in the land clearing work in order to supply organic materials and to make soil swollen instead of burning of just removing. 3) The equipments such as bulldozers, harrows, power tillers and so on should be prepared in order to do a systematic work in the land clearing. 4) The work of pulling-up roots is dependent upon the forms of roots spreading under the ground. The work of the pulling-up the straight roots was most difficult. 5) The land clearing work of the wrinkled style blocks was easy in pulling up roots and in the time of first plowing. The harrowing work could also be simply done. 6) The amount of soil carried was $240m^3/10a$, 15.6% increased amount from the standard block, while the required time of clearing work was 2 hours 15 minutes 45 seconds/10a, the one third of time required for the standard block. 7) The time disc harrowing work increased 50%, or 15 minutes/10a compared to the harrowing work required in the cultivated soil. 8) The time of rotary tilling increased 2.4 times or 1 hour 47 minutes 43 seconds/10a compared to the time required in the cultivated soil. 9) The reclamed land should be fertilized according to the soil quality, especially added fertilizer should be more than 1,200kg/10a, limes 20kg/10a. In order to produce added fertilizer grass fields should be needed. 10) The experiment of pasture growing is now progressing and therefore the effect of land clearing and the degree of developed soil will be investigated before long.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.